Tomasz Szwed’s research while affiliated with University of Life Sciences in Poznań and other places

This study investigates the effects of aging trees on wood properties, which are caused by climate change, the withdrawal of coniferous species from Central Europe, and the increased crown sweep in old beech stands. The research was carried out in old tree stands with a high proportion of Scots pine (Pinus sylvestris L.) and beech (Fagus sylvatica L.) species. The collected material was from five tree pine stands aged between 151 and 182 and three beech stands between the ages of 165 and 184. The samples were subjected to an analysis of wood properties such as density and modulus of elasticity. The results and findings of this study indicate that the Scots pine currently reaches the optimal wood tissue quality at around 80 years of age, which is approximately 20 years earlier than the species’ anticipated cutting age. However, the beech, which reaches maturity at about 120–140 years, reaches the maximal quality of wood tissue already at the age of 80–90 years. Above the age of 110, the quality of beech wood (density and modulus of elasticity) decreases. Moreover, it is necessary to emphasize that the radial trend of wood density does not coincide with the trend of the modulus of elasticity. Additionally, it is found that wood density is not a perfect representation of its mechanical qualities; it can, however, be regarded as a measure of the technical quality of wood tissue. The results indicate that the pine and the beech that grow on the European Plain mature faster and reach technical quality earlier than just a couple of decades before.

Climate change and the gradual phaseout of the spruce from Central Europe inspired us to study the effects of the ageing process of trees on wood properties. This study was conducted in old tree stands with significant involvement of the spruce (Picea abies (L.) H. Karst) in the ages between 122 and 177 years. The study material (samples) was collected from the selected trees to study wood properties such as density, resilience to compressive strength, resilience to bending strength, and modulus of elasticity. The results and findings of this study indicate that the spruce currently reaches the optimal technical quality of wood tissue at approximately 60 years of age. It is approximately 20 years earlier than the planned cutting age for the species. This could be due to water stress which led to adaptive changes in the wood tissue and earlier technical maturation of the wood in the studied trees. Significant radiant variabilities of wood properties of the Norway spruce were observed. It was determined that wood density does not fully reflect its mechanical properties, and it can be considered an indicator of the technical quality of wood tissue, but only within a limited scope. The results obtained may not only be applied in optimising the use of wood from spruce stands. They can also indicate the need to change the approach to managing spruce stands and their conversion towards broadleaf species.

This study was conducted in Central Europe (Poland) in pine forests that were subjected to the process of resin harvesting in the 1970s. Forty trees were designated for the study, which had one or two resin blazes. The objectives of the experiment were to determine the effect of resin tapping on the changes in annual growth, wood density, and mechanical strength of wood in the damaged trees. Resin tapping affected the development dynamics, especially in trees with a single resin blaze. In addition, bark cutting affected wood density over the cross-section. However, no significant variation was found in terms of the mechanical properties of wood, which may support the theory of adaptive tree growth and optimization of tree’s structure to its functions.

This experiment was conducted in the pine woods of central Europe at a research area established in 1951. The experimental area of 1.35 ha was set up in a 14-year-old pine tree stand, which was divided into lots, and the pruning procedure took place in different variants. Some lots constituted control lots without pruned trees. The trees were pruned in four variants, reducing the living tree crown by 1/4, 1/3, 1/2, and 2/3 of its length. The study’s main aim was to determine the influence of pruning forest trees on the tree tissue. Moreover, the study attempted to answer whether pruning was a significant procedure for wood valorisation, and if yes, then which variant was the optimal one for Scots pine growing on the European plain. The results indicated a significant impact of pruning young pine tree stands on the properties of wood tissue, which differed regarding the adopted pruning variant. Significant differences in the width of annual rings, the size of the particular areas of the annual rings (latewood or earlywood), and the wood density depending on the pruning variant were observed. Furthermore, the results indicated that pruning induced numerous processes, which optimised the physiological and mechanical functions of the tree trunks. The outcome of this optimisation was, among others, the diversification of the vascular and strengthening area of the annual ring as well as the wood density, which was a reaction to reducing a part of the assimilation apparatus. From the technical wood value viewpoint, the optimal pruning variant for pine was between 1/3 to 1/2 of the living crown.