Li Wang’s research while affiliated with Sun Yat-sen University and other places

To analyze the typical characteristics of accidents occurring during the startup of a supercritical water reactor (SCWR), a comprehensive SCWR system model was established with the SCTRAN analysis code, based on models of the high-performance light-water reactor (HPLWR) steam cycle, SCWR circulation startup loop, passive safety systems, and CSR1000 core parameters. According to the sequence of the loss of coolant flow accident (LOFA), without a safety system and trigger signal of the safety system under the rated condition, a new trigger signal during the startup was designed and then used to assess “LOFA,” “uncontrolled CR withdrawal accident,” and “loss of coolant accident (LOCA)” during the startup process. The results show that the new trigger signal can ensure the effective and timely response of the safety system, as well as reactor safety during the startup process. Moreover, the maximum cladding surface temperature (MCST) of the reactor peaks (850 °C, well below the safety criterion of 1260 °C) at the end of the fourth stage of the startup process in the case of LOCA.

Startup system, the design of startup sequences analysis is an important part of SCWR design. A thermal hydraulic system analysis code for supercritical water reactor named SCTRAN is used to model the entire startup system based on the circulation loop for startup and once-through direct cycle. The problem of the heat transfer coefficient (HTC) does not accurately capture deterioration phenomenon, the HTC is calculated as a discontinuity in the mode transfer region, its low prediction accuracy above the quasi-critical region have been solved by the new wall heat transfer model. Especially, the look-up table would not be used to obtain the HTC and achieves high prediction accuracy across the critical region, unless the pressure is higher than 19 MPa. After that, to get a smooth recirculation variable pressure startup process, the system model integrates the control system which can controls the temperature, the steam drum water level, the thermal power, and the coolant flow rate. Based on the CSR1000 core and entire once-through direct cycle and circulation loop for startup, four stages under control systems, from low pressure to full power condition in recirculation startup process, were analyzed with code SCTRAN and wall heat transfer model was modified. The calculation results show that the recirculation system can startup from subcritical state to full power state without issue of CHF. The control system can control the parameters quite well and maximum cladding temperature (MCST) can be limited under 650 °C in the startup process. The modified SCTRAN code in this paper can further expand the computational range and computational accuracy. The full-scale control system can meet the needs of parameters expected response.

Supercritical-pressure light water-cooled reactors (SCWR) are the only water cooled reactor types in Generation IV nuclear energy systems. Startup systems, and their associated startup characteristic analyses, are important components of the SCWR design. To analyze the entire startup system, we propose a wall heat transfer model in a paper, based on the results from a supercritical transient analysis code named SCTRAN developed by Xi'an Jiao tong University. In this work, we propose a new heat transfer mode selection process. Additionally, the most appropriate heat transfer coefficient selection method is chosen from existing state-of-the-art methods. Within the model development section of the work, we solve the problem of discontinuous heat transfer coefficients in the logic transformation step. When the pressure is greater than 19 Mpa, a look-up table method is used to obtain the heat transfer coefficients with the best prediction accuracy across the critical region. Then, we describe a control strategy for the startup process that includes a description of the control objects for coolant flow rate, heat-exchange outlet temperature, system pressure, core thermal power, steam drum water-level and the once-through direct cycle loop inlet temperature. Different control schemes are set-up according to different control objectives of the startup phases. Based on CSR1000 reactor, an analytical model, which includes a circulation loop and once-through direct cycle loop is established, and four startup processes, with control systems, are proposed. The calculation results show that the thermal parameters of the circulation loop and the once-through direct cycle meets all expectations. The maximum cladding surface temperature remains below the limit temperature of 650°C. The feasibility of the startup scheme and the security of the startup process are verified.