Kazuo Miki’s research while affiliated with Toyota Central Research and Development Laboratories and other places

We developed a 50th-percentile American male pedestrian model including a detailed brain, and the mechanical responses and kinematic biofidelity predicted by this model were validated against the available cadaveric test data. Vehicle-to-pedestrian impact simulations were then performed to investigate a potential mechanism for traumatic brain injury resulting from a lateral blunt impact to the head. Due to inertia of the brain mass, it was found that the average traction force produced in the cervical spinal cord exceeded 50 N in the impact involving a sport utility vehicle and 25 N in the impact involving a sedan, when the striking vehicle was travelling at 40 km/h. This inertial loading may play a key role in a brainstem, or upper-cervical-cord, lesion occurring before head strike. Results of this study suggest that close attention should be paid to pedestrian kinematics during free flight even before the head makes primary contact with the striking vehicle.

The simulation that uses the finite element method aiming at the clarification of the appearance of disease mechanism of the cervical spondylotic myelopathy and the grasp of the stress of spinal cord for the treatment method selection is being done now. However, a necessary dynamic characteristic of pia matter of the spinal cord has not been elucidated enough. In this study, pig's dynamic characteristic of pia matter was obtained. And, the state of the stress of spinal cord was analyzed by the FEM simulation that assumed the spinal cord pressure by making of the cervical flexion myelopathy.

Injuries of the human brain and spinal cord associated with the central nervous system (CNS) are seen in automotive accidents. CNS injuries are generally categorized into severe injuries (AIS 3+). However, it is not clear how the restraint conditions affect the CNS injuries. This paper presents a newly developed three-dimensional (3D) finite element head-neck model in order to investigate the biomechanical responses of the brain-spinal cord complex. The head model consists of the scalp, skull, and a detailed description of the brain including the cerebrum, cerebellum, brainstem with distinct white and gray matter, cerebral spinal fluid (CSF), sagittal sinus, dura, pia, arachnoid, meninx, falx cerebri, and tentorium. Additionally, the neck model consists of the cervical vertebral bodies, intervertebral discs, muscles, ligaments, spinal cord with white and gray matter, cervical pia, and CSF. The two models were linked together to construct a finite element (FE) model of the brain-spinal cord complex. The material stiffness and failure properties of porcine cervical pia mater were measured from uniaxial tensile tests with various strain rates at Yamaguchi University. The head-neck model was validated against three sets of brain test data obtained by Nahum et al. (1977), Trosseille et al. (1992), and Hardy et al. (2001) and two sets of neck test data obtained from Thunnissen et al. (1995) and Pintar et al. (1995). Additionally, a series of parametric studies were conducted to investigate the effects of restraint conditions on CNS injuries. The injury criteria for brain injuries were based on Cumulative Strain Damage Measure, while those for spinal cord injuries were based on the ultimate strains of the spinal cord and pia mater. It was found that the brain-spinal cord model was useful to investigate the relationship between the restraint conditions and CNS injuries.

The mass density, Young's modulus (E), tangent modulus (Et), and yield stress (sigma y) of the human ribs, sternum, internal organs, and muscles play important roles when determining impact responses of the chest associated with pendulum impact. A series of parametric studies was conducted using a commercially available three-dimensional finite element (FE) model, Total HUman Model for Safety (THUMS) of the whole human body, to determine the effect of changing these material properties on the predicted impact force, chest deflection, and the number of rib fractures and fractured ribs. Results from this parametric study indicate that the initial chest apparent stiffness was mainly influenced by the stiffness and mass density of the superficial muscles covering the torso. The number of rib fractures and fractured ribs was primarily determined by the stiffness of the ribcage. Similarly, the stiffness of the ribcage and internal organs contributed to the maximum chest deflection in frontal impact, while the maximum chest deflection for lateral impact was mainly affected by the stiffness of the ribcage. Additionally, the total mass of the whole chest had a moderately effect on the number of rib fractures.

The simulation that uses the finite element method aiming at the clarification of the appearance of disease mechanism of the cervical spondylotic myelopathy and the grasp of the stress of spinal cord for the treatment method selection is being done now. However, a necessary dynamic characteristic of pia matter of the spinal cord has not been elucidated enough. In this study, pig's dynamic characteristic of pia matter was obtained. And, the state of the stress of spinal cord was analyzed by the FEM simulation that assumed the spinal cord pressure by making of the ligament thickening.

Several three-dimensional (3D) finite element (FE) models of the human body have been developed to elucidate injury mechanisms due to automotive crashes. However, these models are mainly focused on 50(th) percentile male. As a first step towards a better understanding of injury biomechanics in the small female, a 3D FE model of a 5(th) percentile female human chest (FEM-5F) has been developed and validated against experimental data obtained from two sets of frontal impact, one set of lateral impact, two sets of oblique impact and a series of ballistic impacts. Two previous FE models, a small female Total HUman Model for Safety (THUMS-AF05) occupant version 1.0Beta (Kimpara et al. 2002) and the Wayne State University Human Thoracic Model (WSUHTM, Wang 1995 and Shah et al. 2001) were integrated and modified for this model development. The model incorporated not only geometrical gender differences, such as location of the internal organs and structure of the bony skeleton, but also the biomechanical differences of the ribs due to gender. It includes a detailed description of the sternum, ribs, costal cartilage, thoracic spine, skin, superficial muscles, intercostal muscles, heart, lung, diaphragm, major blood vessels and simplified abdominal internal organs and has been validated against a series of six cadaveric experiments on the small female reported by Nahum et al. (1970), Kroell et al. (1974), Viano (1989), Talantikite et al. (1998) and Wilhelm (2003). Results predicted by the model were well-matched to these experimental data for a range of impact speeds and impactor masses. More research is needed in order to increase the accuracy of predicting rib fractures so that the mechanisms responsible for small female injury can be more clearly defined.

Posterior translation of the tibia with respect to the femur can stretch the posterior cruciate ligament (PCL). Fifteen millimeters of relative displacement between the femur and tibia is known as the Injury Assessment Reference Value (IARV) for the PCL injury. Since the anterior protuberance of the tibial plateau can be the first site of contact when the knee is flexed, the knee bolster is generally designed with an inclined surface so as not to directly load the projection in frontal crashes. It should be noted, however, that the initial flexion angle of the occupant knee can vary among individuals and the knee flexion angle can change due to the occupant motion. The behavior of the tibial protuberance related to the knee flexion angle has not been described yet. The instantaneous angle of the knee joint at the timing of restraining the knee should be known to manage the geometry and functions of knee restraint devices. The purposes of this study are first to understand the kinematics of the knee joint during flexion, and second to characterize the mechanics of the knee joint under anterior-posterior loading. A finite element model of the knee joint, extracted from the Total Human Model for Safety (THUMS), was used to analyze the mechanism. The model was validated against kinematics and mechanical responses of the human knee joint. By tracking the relative positions and angles between the patella and the tibia in a knee flexing simulation, the magnitude of the tibial anterior protuberance was described as a function of the knee joint angle. The model revealed that the mechanics of the knee joint was characterized as a combination of stiffness of the patella-femur structure and the PCL It was also found that the magnitude of the tibial anterior protuberance determined the amount of initial stretch of the PCL in anterior-posterior loading. Based on the knee joint kinematics and mechanics, an interference boundary was proposed for different knee flexion angles, so as not to directly load the anterior protuberance of the tibial plateau in restraining of the knee. A frontal crash simulation was performed using a partial vehicle model with the THUMS seated. The performance and effects of the knee airbag, as one of the candidates for knee restraint devices, were evaluated through the simulation.