Bernd Kretzschmar’s research while affiliated with Leibniz Institute of Polymer Research and other places

The processing conditions were varied during the production of polycarbonate-based composites with the multiwalled carbon nanotubes (MWCNTs) Baytubes® C150 P (Bayer MaterialScience AG, Leverkusen, Germany), by melt mixing with an extruder on a laboratory scale. These included the screw design, rotation speed, throughput, feeding position and MWCNT content. Particular attention was paid to the shortening of the MWCNT length as a function of the conditions mentioned. It was found that there is a correlation between the applied specific mechanical energy (SME) during the melt mixing process and MWCNT dispersion, which was quantified by the agglomerate area ratio of the non-dispersed nanotubes based on optical microscopic analysis. The higher the SME value, the lower this ratio, which indicates better dispersion. Above an SME value of about 0.4 kWh/kg, no further improvement in dispersion was achieved. The MWCNT length, as measured by the quantitative analysis of TEM images of the MWCNTs dissolved from the composites, decreased with the SME value down to values of 44% of the original MWCNT length. At a constant loading of 3 wt.%, the tensile strength and tensile modulus were almost independent of the SME, while the elongation at break and notched impact strength showed an increasing trend. The variation in the feeding position showed that feeding the MWCNTs into a side feeder led to slightly better electrical and mechanical properties for both types of MWCNTs studied (Baytubes® C150 P and Nanocyl™ NC7000 (Nanocyl S.A., Sambreville, Belgium)). However, feeding into the hopper led to better CNT dispersion with Baytubes® C150 P, while this was the case with Nanocyl™ NC7000 when feeding into the side feeder. The screw profile had an influence on the dispersion, the MWCNT length and the electrical resistance, but only to a small extent. Distributive screws led to a greater shortening of the MWCNT length than dispersive screws. By varying the MWCNT content, it was shown that a greater MWCNT shortening occurred at higher loadings. Two-stage masterbatch dilution leads to stronger shortening than composite production with direct MWCNT incorporation.

In the present study, melt-mixed composites based of poly (vinylidene fluoride) (PVDF) and fillers with different aspect ratios (carbon nanotubes (CNTs), carbon black (CB)) and their mixtures in composites were investigated whereby compression-molded plates were compared with melt-extruded films. The processing-related orientation of CNTs with a high aspect ratio leads to direction-dependent electrical and mechanical properties, which can be reduced by using mixed filler systems with the low aspect ratio CB. An upscaling of melt mixing from small scale to laboratory scale was carried out. From extruded materials, films were prepared down to a thickness of 50 µm by cast film extrusion under variation of the processing parameters. By combining CB and CNTs in PVDF, especially the electrical conductivity through the film could be increased compared to PVDF/CNT composites due to additional contact points in the sample thickness. The alignment of the fillers in the two directions within the films was deduced from the differences in electrical and mechanical film properties, which showed higher values in the extrusion direction than perpendicular to it.

The method of measuring electrical volume resistivity in different directions was applied to characterize the filler orientation in melt mixed polymer composites containing different carbon fillers. For this purpose, various kinds of fillers with different geometries and aspect ratios were selected, namely carbon black (CB), graphite (G) and expanded graphite (EG), branched multiwalled carbon nanotubes (b-MWCNTs), non-branched multiwalled carbon nanotubes (MWCNTs), and single-walled carbon nanotubes (SWCNTs). As it is well known that the shaping process also plays an important role in the achieved electrical properties, this study compares results for compression molded plates with random filler orientations in the plane as well as extruded films, which have, moreover, conductivity differences between extrusion direction and perpendicular to the plane. Additionally, the polymer matrix type (poly (vinylidene fluoride) (PVDF), acrylonitrile butadiene styrene (ABS), polyamide 6 (PA6)) and filler concentration were varied. For the electrical measurements, a device able to measure the electrical conductivity in two directions was developed and constructed. The filler orientation was analyzed using the ratio σin/th calculated as in-plane conductivity σin-plane (σin) divided by through-plane conductivity σthrough-plane (σth). The ratio σin/th is expected to increase with more pronounced filler orientation in the processing direction. In the extruded films, alignment within the plane was assigned by dividing the in-plane conductivity in the extrusion direction (x) by the in-plane conductivity perpendicular to the extrusion direction (y). The conductivity ratios depend on filler type and concentration and are higher the higher the filler aspect ratio and the closer the filler content is to the percolation concentration.

In this study commercially available multiwalled carbon nanotubes (2-8 wt.%) were incorporated in polypropylene (PP) by direct powder feeding or by a masterbatch dilution procedure using a twin-screw extruder. The influence of a supplemental, electrical non-conductive talc or electrically conductive carbon black (CB), filler on the resulting composite properties was investigated. In comparison to the direct carbon nanotube (CNT) incorporation the masterbatch dilution step resulted in improved CNT macro dispersion. The use of the supplemental fillers CB or talc does not show a significant influence on the CNT dispersion state. When compared to direct CNT incorporation, the second compounding process involved in masterbatch dilution leads to higher electrical resistivity of injection molded samples. On the other hand, the supplemental fillers talc or CB decreased the electrical resistivity values. With the addition of talc or CB an increase of the Young’s modulus due to the reinforcing effect of the second filler was achieved. However, no synergistic effect between the used supplemental fillers and the CNT on the mechanical properties was obtained.

The majority of polymers possesses low thermal conductivity and behaves as electrical insulators. In this work, the thermal conductivity of polypropylene (PP) was increased by adding thermally conductive fillers, which were boron nitride (BN) and titanium dioxide (TiO2). The influence of fillers with different particle sizes/distributions as well as their combinations on the thermal conductivity was systematically investigated at different concentrations. PP/BN composites with a balanced property profile concerning electrical, rheological and mechanical properties were obtained. With a content of 20 vol.-% BN (mean particle size 45 µm) the thermal conductivity was raised above 1 W/mK while the electrical and dielectric properties were only insignificantly affected and melt processability as well as mechanical values of PP were maintained.

Poly(vinyl chloride)/nitrile butadiene rubber (PVC/NBR) alloys were melt-mixed using a Brabender Plasticorder at 180 ∘ C and 50 rpm rotor speed. Alloys obtained by melt mixing from PVC and NBR were formulated with wood-flour- (WF-) based olive residue, a natural byproduct from olive oil extraction industry. WF was progressively increased from 0 to 30 phr. The effects of WF loadings on the tensile properties of the fabricated samples were inspected. The torque rheometry, which is an indirect indication of the melt strength, is reported. The pattern of water uptake for the composites was checked as a function WF loading. The fracture mode and the quality of bonding of the alloy with and without filler are studied using electron scanning microscope (SEM).

Polylactide (PLA)/linear low‐density polyethylene (LLDPE), (PLA/LLDPE), blends and nanocomposites were prepared by melt mixing process with a view to fine tune the properties. Two different commercial‐grade nanoclays, Cloisite® 30B (30B) and Cloisite® 15A (15A) were used. A terpolymer of ethylene, butylacrylate (BA) and glycidylmethacrylate (GMA) was used as a reactive compatibilizer. The influence of type of clay on the morphology and mechanical properties of two PLA‐rich and LLDPE‐rich blend systems was studied. Morphological analysis using X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy revealed that the organoclay layers were dispersed largely at the interface of PLA/LLDPE. Decreasing the PLA content changed the morphology from droplet‐in matrix to coarse co‐continuous. In comparison with 30B, due to less affinity of 15A towards compatibilizer and PLA phase, the reduction of the size of dispersed phase was less than that of the equivalent 30B composites. The mechanical results demonstrated that the composites containing both types of organoclay exhibited higher modulus but lower elongation and tensile strength as compared to the neat blends. The injection molded nanocomposites were shown to have the sequential fracture behavior during tensile test. The tensile testing results on the neat blends and nanocomposites showed significant increase in elongation at break and decrease in the modulus as compared with the neat PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 749‐758, 2013

The reactivity of the flame retardant and its decomposition temperature control the condensed- phase action in bisphenol A polycarbonate/acrylonitrile–butadiene–styrene/polytetrafluoroethylene (PC/ABSPTFE) blends. Thus, to increase charring in the condensed phase of PC/ABSPTFE + aryl phosphate, two halogen-free flame retardants were synthesized: 3,3,5-trimethylcyclohexylbisphenol bis(diphenyl phosphate) (TMC-BDP) and bisphenol A bis(diethyl phosphate) (BEP). Their performance is compared to bisphenol A bis(diphenyl phosphate) (BDP) in PC/ABSPTFE blend. The comprehensive study was carried out using thermogravimetry (TG); TG coupled with Fourier transform infrared spectrometer (TGFTIR); the Underwriters Laboratory burning chamber (UL 94); limiting oxygen index (LOI); cone calorimeter at different irradiations; tensile, bending and heat distortion temperature tests; as well as rheological studies and differential scanning calorimeter (DSC). With respect to pyrolysis, TMC-BDP works as well as BDP in the PC/ABSPTFE blend by enhancing the cross-linking of PC, whereas BEP shows worse performance because it prefers cross-linking with itself rather than with PC. As to its fire behavior, PC/ABSPTFE + TMC-BDP presents results very similar to PC/ABSPTFE + BDP; the blend PC/ABSPTFE + BEP shows lower flame inhibition and higher total heat evolved (THE). The UL 94 for the materials with TMC-BDP and BDP improved from HB to V0 for specimens of 3.2 mm thickness compared to PC/ABSPTFE and PC/ABSPTFE + BEP; the LOI increased from around 24% up to around 28%, respectively. BEP works as the strongest plasticizer in PC/ABSPTFE, whereas the blends with TMC-BDP and BDP present the same rheological properties. PC/ABSPTFE + TMC-BDP exhibits the best mechanical properties among all flame-retarded blends.

In this work we investigate mechanical properties and structure of PA6/ZnO and PA6/Al2O3 nanocomposites to understand the effect of different nanoparticles on the polymer matrix. Mechanical experiment results show that the mechanical reinforcement effect after loading ZnO nanoparticles is better than that of loading Al2O3 nanoparticles. At 10% ZnO loading, the elastic modulus increases to about two times of that of pure PA6, and the yield stress increases about 30%. And the elongation at break has no obvious decrease even at high ZnO loading. In order to understand the reason of better mechanical reinforcement after incorporating ZnO nanoparticles, microstructure and crystallization behavior of the samples were investigated. The results indicate that the better reinforcement of mechanical properties after loading ZnO was attributed to enhanced interfacial adhesion between ZnO nanoparticles and PA6 matrix at high ZnO content.