ArticlePDF AvailableLiterature Review

Relevance of Specific Surface of Mixed Oxide Derived from Layered Double Hydroxides on the Rheological Properties and Porosity of Cement Pastes

June 2024
ACS Applied Materials & Interfaces

DOI:10.1021/acsami.4c01949

License
CC BY 4.0

Authors:

Caio Carvalho dos Santos

São Paulo State University

S.H. Pulcinelli

São Paulo State University

Celso V Santilli

São Paulo State University

Cement-based products are the synthetic materials most used by humans, with consequent environmental impacts. One strategy that can assist in mitigating the adverse environmental effects of these materials involves the incorporation of multifunctional nanostructured additives. The objective of this work was to demonstrate the efficacy of incorporating mixed oxides (MO) derived from layered double hydroxides (LDH) to control the rheology and porosity of cement-based matrices. Thermal aging of LDH enabled the preparation of MO with different specific surface areas (SSA) for incorporation in different amounts in Portland cement. A low proportion of MO and low SSA increased workability by 22%. In contrast, a high proportion of MO and high SSA led to a 2.4-fold acceleration of cement consolidation and a 36.9% decrease of the porosity of the composite. These features could be attributed to additive–matrix interactions, with the LDH memory effect playing key roles in the cement crystal seed process and in competition for the absorption of free water within the cement paste. Therefore, the unprecedent results obtained suggest that the quantity and SSA of MO are key parameters to fine-tune the paste rheology and structure of hidrated cement. The MO materials showed easy adaptability and excellent potential for use as multifunctional additives in the production of eco-friendly, high-performance cement paste formulations with controllable properties according to the desired application.

Content uploaded by Caio Carvalho dos Santos

Content may be subject to copyright.

Content uploaded by Caio Carvalho dos Santos

Content may be subject to copyright.

A preview of the PDF is not available

ResearchGate has not been able to resolve any citations for this publication.

Cement hydration mechanisms through time – a review

Article

Full-text available

Jun 2023
J MATER SCI

In this article the progress of the research on cement hydration mechanisms is critically reviewed, starting with the work of Le Chatelier and Michaelis during the late nineteenth century. Proposed mechanisms are discussed in the light of experimental data to highlight the role of new or improved analytical techniques. The focus of this article lies on the dormant period and the silicate reaction. Today many of the mechanisms proposed throughout time cannot withstand experimental evidence and need to be rejected, including the classical protective hydrate layer theory. However, it seems likely that hydrated surface species are involved in the mechanism. Theories that aim to explain the rate changes solely based on the nucleation and growth of portlandite can also not withstand experimental evidence. Nevertheless, the retardation of portlandite crystal growth through silicate ions is a relevant factor. Especially since it might present a mechanism for the nucleation of calcium silicate hydrate (C–S–H), backing up theories that propose C–S–H and portlandite to grow from the same nuclei. Finally, an overview over facts, that are currently considered to be valid and hence need to be regarded in the future mechanisms is given.

Small oscillatory rheology and cementitious particle interactions

Article

Full-text available

Apr 2022
CEMENT CONCRETE RES

Oscillatory rheology has proved a promising method to measure the nature of interactions between inorganic particles in suspension. In this work, small oscillatory rheology (SAOS) is used to compare the nature of interactions in an ordinary Portland cement (OPC) and a more sustainable alkali-activated binder (AAB). The interstitial solution of the AAB is varied by adding calcium chloride. The linear elastic regime is characterized as a function of volume concentration, in a range for which an attractive gel-like behavior is observed. SAOS measurements show that the nature of interactions in AAB is different from those in OPC and changes with calcium concentration. The influence of calcium over the surface properties of AAB is further proven by the fluidifying effect of polycarboxylether (PCE) when [Ca 2+ ] is increased. The results obtained confirm the relevance of SAOS to qualitatively assess the state of aggregation in cementitious slurries and select candidates for cement substitution.

The Improvement of Durability of Reinforced Concretes for Sustainable Structures: A Review on Different Approaches

Article

Full-text available

Apr 2022

The topic of sustainability of reinforced concrete structures is strictly related with their durability in aggressive environments. In particular, at equal environmental impact, the higher the durability of construction materials, the higher the sustainability. The present review deals with the possible strategies aimed at producing sustainable and durable reinforced concrete structures in different environments. It focuses on the design methodologies as well as the use of unconventional corrosion-resistant reinforcements, alternative binders to Portland cement, and innovative or traditional solutions for reinforced concrete protection and prevention against rebars corrosion such as corrosion inhibitors, coatings, self-healing techniques, and waterproofing aggregates. Analysis of the scientific literature highlights that there is no preferential way for the production of “green” concrete but that the sustainability of the building materials can only be achieved by implementing simultaneous multiple strategies aimed at reducing environmental impact and improving both durability and performances.

Rheology modelling of cement paste with manufactured sand and silica fume: Comparing suspension models with artificial neural network predictions

Article

Full-text available

Jan 2022
CONSTR BUILD MATER

Manufactured sand is increasingly used in concrete and predicting the rheology of such suspensions based on their composition are necessary. In this study, emphasis is on cement pastes with manufactured sand and silica fume. An artificial neural network, namely multilayer perceptron, is compared with nine suspension models: two liquid thickness models, the relative concentration of solids and six relative viscosity models based on the relative concentration of solids. Measurements on 107 mixes with filler (0–125 µm) from manufactured sand are conducted, acquiring yield stress, plastic viscosity, flow resistance ratio and mini slump flow. None of the suspension models offer good correlations to the measured parameters for all mixes, but an increase in prediction accuracy is seen for subsets of materials, especially mixes without silica fume. The artificial neural network outperforms the suspension models, providing a coefficient of determination between 0.84 and 0.91 for all mixes, thus illuminating a new pathway for cement paste rheology modelling.

Comparative Study of Different Measurement Methods for Characterizing Rheological Properties of Lubrication Layer

Article

Full-text available

Jun 2021
MOLECULES

The lubrication layer plays a governing role in predicting the pumpability of fresh concrete. To determine the effect of measurement methods on the characterization of the rheological properties of the lubrication layer, different measurement systems, including Sliper, tribometer, and the utilization of a mortar rheometer, were employed. The rheological properties and workability of bulk concrete were measured in parallel to investigate the correlation between them and the rheological properties of the lubrication layer. The results show that the measured values of the rheological parameters of the lubrication layer differ due to the systematic deviation between different measurement methods. The results obtained by both tribometer and mortar rheometer were well-correlated, having a linear relationship with the rheological parameters of bulk concrete. The correlation coefficient between results gained with Sliper and rheological parameters of concrete or lubrication layer determined with other methods was not high enough. Addition friction led to the large accidental error and overestimated yield stress obtained with Sliper. The workability of concrete is only suitable for characterizing the rheological properties of bulk concrete.

Atomic-Level and Surface Structure of Calcium Silicate Hydrate Nanofoils

Article

Sep 2023

Deciphering the calcium silicate hydrate (C-S-H) surface is crucial for unraveling the mechanisms of cement hydration and property development. Experimental observations of C-S-H in cement systems suggest a surface termination which is fundamentally different from the silicate-terminated surface assumed in many atomistic level studies. Here, a new multiparameter approach to describing the (001) basal C-S-H surface is developed, which considers how the surface termination affects the overall properties (Ca/Si ratio, mean chain length, relative concentration of silanol and hydroxide groups). Contrary to current beliefs, it is concluded that the (001) C-S-H surface is dominantly calcium terminated. Finally, an adsorption mechanism for calcium and hydroxide ions is proposed, which is in agreement with the surface charge densities observed in previous studies.

Laboratory investigation of the chloride ingress into cement mortar incorporating a novel core-shell nanomaterial

Article

May 2023
CONSTR BUILD MATER

The built-in limitations of the separate use of nano-SiO 2 (NS) and layered double hydroxides (LDH) necessitate their combined use for improving the resistance of chloride transport into concrete. This study investigates the effect of a novel nano-SiO 2 @MgAl-LDH (NS@LDH) core-shell material (fabricated by in-situ co-precipitation method) on chloride transport of cement mortar through a comparative experiment. The mechanical properties, chloride-bound isotherms, rapid chloride migration (RCM), and chloride natural diffusion of mortar specimens were measured. The results show that the addition of NS@LDH improves both the compressive and flexural strength of mortar. Compared to mortars incorporating NS and LDH separately, the NS@LDH incorporated mortars exhibit a higher resistance to chloride transport. The chloride diffusion coefficient of the 2 % NS@LDH incorporated mortar is the lowest (reduced by 79 %). The NS@LDH induced combined effect of a significantly increased chloride-bound ability and refined microscopic structures contributes to the elevated resistance to chloride transport.

MgAl-Layered Double Hydroxide Nanoparticles as Smart Nanofillers To Control the Rheological Properties and the Residual Porosity of Cement-Based Materials

Article

Jun 2022

Pore structure characteristics of reactive powder concrete composites with surface-modified carbon nanotubes

Article

Feb 2022
CEMENT CONCRETE COMP

The macroscopic properties of carbon nanotubes (CNTs) modified reactive powder concrete (RPC) composites are closely related to their pore structure characteristics, but the structural nature of PRC composites and the effect of CNTs on their pore structure remain unclear. To comprehensively understand the pore structure of RPC composites with surface-modified CNTs and then control their properties, both the mercury intrusion porosimetry (MIP) and low-field nuclear magnetic resonance (LF-NMR) technologies were used to characterize the pore structure characteristics of RPC composites. Experimental results showed there exist large number of nano-scale pores (mainly interlayer and gel pores) with the radius range of 0.3–20 nm in RPC composites. All types of surface-modified CNTs incorporated in this study reduce the pore content and size of RPC composites, thereby modifying the pore structure of RPC. However, different CNTs present varying effects on the pore (especially nano-scale pore) structure characteristics. Among all surface-modified CNTs, the hydroxyl functionalized and nickel-coated CNTs cause the structural shrinkage of C-S-H gel, while the carboxyl functionalized CNTs induce the transformation of some nano-scale pores inside the gel. The effects of surface-modified CNTs on the pore structure of RPC composites are mainly on the nano- and micrometer scale. CNTs can not only increase the matrix compactness of RPC composites and enhance the network structure of hydration products, but also induce the pore water conversion inside C-S-H layers.

Application of layered double hydroxides (LDHs) in corrosion resistance of reinforced concrete-state of the art

Article

Nov 2021
CONSTR BUILD MATER

Hydrotalcite materials, also known as layered double hydroxides (LDHs), have strong ion exchange properties, and are widely used in the field of reinforced concrete corrosion protection. LDHs can improve the compactness and mechanical properties of concrete through physical and chemical effects, combined with its ion exchange performance, and jointly improve the resistance to chloride ion erosion. Compared with directly adding corrosion inhibitors, LDHs intercalating with corrosion inhibitors usually have multiple functions such as reducing corrosion inhibitor degradation, prolonging the long-term effect of corrosion protection, improving environmental alkalinity, and adsorbing corrosive ions. Among the preparation methods of LDHs intercalating with corrosion inhibitors, calcination-rehydration method has greater potential for large-scale application. This article reviews the preparation and intercalation modification methods of LDHs, their influence on the properties of concrete, the corrosion resistance mechanism and influencing factors of adsorption of chloride ion in concrete. Finally, the future research and application of LDHs in concrete are prospected, and the problems that need to be solved are put forward. It is expected to serve as a reference for the preparation of efficient, green and economical LDHs concrete, and provide more possibilities for the application of LDHs in practical concrete engineering.