Content uploaded by Andri Kumoro
Author content
All content in this area was uploaded by Andri Kumoro on Aug 17, 2021
Content may be subject to copyright.
Available via license: CC BY 3.0
Content may be subject to copyright.
IOP Conference Series: Materials Science and Engineering
PAPER • OPEN ACCESS
A brief review on the characteristics, extraction and potential industrial
applications of citronella grass (
Cymbopogon nardus
) and lemongrass
(
Cymbopogon citratus
) essential oils
To cite this article: A C Kumoro et al 2021 IOP Conf. Ser.: Mater. Sci. Eng. 1053 012118
View the article online for updates and enhancements.
This content was downloaded from IP address 182.2.41.185 on 15/06/2021 at 14:47
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution
of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
Published under licence by IOP Publishing Ltd
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
1
A brief review on the characteristics, extraction and potential
industrial applications of citronella grass (Cymbopogon
nardus) and lemongrass (Cymbopogon citratus) essential oils
A C Kumoro1,2, D H Wardhani1,2, D S Retnowati1,2 and K Haryani1
1)Department of Chemical Engineering, Faculty of Engineering, Universitas
Diponegoro. Prof. H. Soedarto, SH Road-Tembalang, Semarang-INDONESIA 50275
2)Institute of Food and Remedies bioMaterial (InFarma), Universitas Diponegoro,
Prof. H. Soedarto, SH Road-Tembalang, Semarang-INDONESIA 50275
E-mail: andrewkomoro@che.undip.ac.id
Abstract. Essential oils can be extracted from the leaves and stalk of aromatic grass plants,
namely the citronella grass (Cymbopogon nardus) and lemongrass (Cymbopogon citratus),
which grow primarily in the tropical and subtropical regions of the world. The word lemon
denotes its unique lemon-like aroma, which is largely contributed by the existence of citral. This
organic compound is an amalgamation of two stereoisomeric monoterpene aldehydes, in which
the trans isomer geranial content is predominant over its cis isomer neral. The essential oil of
lemongrass has been utilised since the old-times in traditional medicine as a natural remedy to
improve circulation, control menstrual cycles, enhance digestion or improve immunity. It is also
used to produce perfumes, flavours, detergents, and pharmaceuticals. Basically, citronella grass
and lemongrass essential oil can be obtained by various extraction methods, such as conventional
solvent extraction, ultrasound-assisted extraction (UAE), steam distillation, hydrodistillation
(HD), microwave-assisted hydrodistillation (MAHD), and supercritical fluid extraction (SFE)
with CO2. SFE is considered as the most selected consumer and environmentally friendly
essential oil extraction method because its traceless solvent in the product. The quality of the
essential oil from aromatic grass strongly depends on the extraction method and operating
conditions. However, the chemical composition of the essential oil of C. nardus and C. citratus
also varies with the geographical origin, cultivation practices, plant age, photoperiod, harvest
period, cultivars, and extraction methods. The chemical markers which have consistently been
identified in the essential oil of aromatic grass are aldehydes, hydrocarbon terpenes, alcohols,
ketones, and esters. This article presents the recent information on extraction methods of
aromatic grass essential oil, chemical composition and its potential in industrial applications.
1. Introduction
Essential oils are plant extracts of various botanical sources, and do not have only origin from flowers,
but from herbs, trees and various other parts of plant. It is predicted that more than 300,000 plant species
grow in the world and approximately10% of them can be categorized as essential oil-bearing plants.
Therefore, they could be used as a source for essential oil production [1]. Essential oils present in various
parts of plant, which are commonly leaves, flowers, seeds, barks and roots. For the plant, essential oils
are believed to be important for the life of the plants due to the existence of specific compounds that
help them against herbivores, insects and infections caused by fungi, bacteria and parasites. The Asian
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
2
continent with its multeity of climates emerges to be the world’s most important producer of essential
oils. In fact, China and India provide a primary role, which subsequently followed by Indonesia, Sri
Lanka, and Vietnam [1].
There are approximately 140 species aromatic grasses species belong to the genus Cymbopogon [3,
4]. Citronella grass (Cymbopogon nardus) and lemongrass (Cymbopogon Citratus), are long-thin leaves
continual medicinal plants mainly cultivated commercially in many parts of tropical and subtropical
areas of Asia, America and Africa [2]. The important citronella grass species include the C. nardus and
C. winterianus, popularly known as Java citronella and Ceylon citronella have been long used in the
traditional medicine and spices market for centuries [3–7]. Being very popular plants in those regions,
depending on the specific uses, these plants also go by many names, such as fever grass, silky heads,
barbed wire grass, and Hierba Luisa.
As one of the grass traditional medicinal plants, C. nardus belongs to Panicodiae family of
Graminales [1]. Physically, C. nardus plant has green and purplish red stems, green to bluish green
leaves, flat elongated leaves resembling reeds with adventitious and clumpy roots. If the leaves are
squeezed, they release a strong pungent aroma [3]. Although C. nardus can grow at an altitude of 200 –
1000 m above sea level (ASL), it grows best on sandy soil with neutral pH at 350-600 m ASL, 18-25oC,
1,800 – 2,500 mm/year precipitation and whole year direct sun light exposure by which highest essential
oil yield and quality. As another aromatic plant, C. citratus (lemongrass) is also a tall grass with densely
tufted fibrous root, which develops rhizomes. Different with C. nardus, this plant possesses short
underground stems with ringed segments and coarse- slightly leathery green leaves in dense clusters.
The plant is a native medicinal plant of India and is now widely cultivated in other tropical and
subtropical countries of Asia, Africa and America continents. Lemongrass contains essential oil in its
specific oil-bearing cells of the parenchyma tissues, mainly exist in the leaves and stalk [4]. Therefore,
generally Lemongrass essential oil is primarily extracted from the leaves, which contain about 12%
(w/w) of essential oil [5]. Lemongrass essential oil exhibits a sherry colour, pungent taste, and lemon-
like odor.
Considering the huge potential cultivation of C. nardus and C. citratus, this review presents the
insight of feasible extraction methods and industrial applications of their essential oil for the effort of
strengthening the economic value of these aromatic grass plants.
2. Chemical composition of citronella grass and lemongrass essential oils
The essential oil composition of aromatic grasses varies significantly at various harvesting stages [2]. If
lemongrass was harvested 5.5 months after planting, 44 compounds accounting 98.64% of the essential
oil components were observed. As lemongrass was harvested 6.5 month after planting, there were only
15 chemical constituents, which represent 98.62% of the essential oil. However, the geranial content in
lemongrass oil increased from 37.58% to 45.95% as the plant leaves were harvested at 5.5 and 6.5
months after planting. Prolong harvest time to 7.5 months after planting slightly decreased the essential
oil content to 42.95%. According to Hanaa et al., the method of drying has a significant effect on the
essential oil content of C. citratus. The highest essential oil content (2.45%) of lemongrass leaves was
achieved if the leaves were dried in an oven at 45°C [6]. They also found lower essential oil yields
(2.10% and 2.12%) of lemongrass leaves if the leaves were dried under sunshine and in shade yielded.
Fortunately, no significant compositional difference between them was observed. Commonly, drying
methods of lemongrass leaves have no tangible effect on the composition of main essential oil
components (neral and geranial) [7].
2.1. Primary chemical compounds
The biochemical compounds present in the essential oil extracted from C. nardus and C. citratus leaves
has been widely investigated using gas chromatography (GC) and gas chromatography- mass
spectrophotometry (GC-MS) methods. Literature surveys demonstrated that the biochemical
compounds vary and depend on the genetic differences, geographical origin, environmental conditions
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
3
of the cultivation area, plant age, photoperiod, farming practices, harvest period, and the extraction
methods. However, such unique compounds as hydrocarbon terpenes, ketones, alcohols, esters and
certain aldehydes have always been identified. The major constituents of the essential oil of aromatic
grasses, commonly known as citronella oil, are citronellal, citronellol, geraniol, citral and eugenol [8].
Indeed, the marker compounds, which correspond to specific chemical constituents within a medicinal
plant can be utilized to verify its potency or identity.
Citral usually presents as the main component of aromatic grass essential oil. Chanthai et al. reported
that geraniol, trans-citral (geranial), cis-citral (neral), -copaene, citronellol, γ-cadinene, δ- cadinene,
eugenol and β-caryophyllene are the main components of citronella grass essential oil [8]. Whereas,
trans-citral (geranial), cis-citral (neral), myrcene, citronellal, humulene, limonene oxide and cis-β-
ocimene being the major constituents of lemongrass essential oil. Citral exists as a mixture of two
geometric isomers, which consists of the trans-isomer (well-known as geranial or citral A) and the cis-
isomer (well-recognized as neral or citral B). In most cases, geranial (0.99 – 48.14%) predominates over
neral (0 – 38.32%). Therefore, the quality of lemongrass essential oil is commonly classified according
to its citral content. A high-quality lemongrass essential oil should contain no less than 75% of citral
[9]. Verma et al. explained that the quality and quantity of lemongrass essential oil are strongly
dependent on the age and time of plant harvest, because the composition and the content of the essential
oil are strictly connected with the developmental stage of the whole plant, plant organs, and cells [10].
The use of fertilizer and the presence of rhizosphere fungi in the cultivation soil usually enhance the
citral content of lemongrass [11]. In addition, they also reported that the harvesting methods usually
only give little influence on the essential oil yield. Tajidin et al. observed that the proportion of young
leaves to older leaves during harvesting determines the high citral content and finally affects the quality
of the essential oil [2].
2.2. Secondary chemical compounds
Other chemical compounds which are often present in the lemongrass essential oil in less than 1 %,
include α-thujene, citronellol, and α-copaene. On the other hand, limonene oxide, citronellal,
germacrene-D and δ-cadinol are the minor constituents of citronella grass essential oil with less than 1%
content [8]. The α-pinene, humulene and α-cubebene present at higher content, which is about 1 – 2%.
Chanthai et al. did not observe the presence of myrcene, α-thujene and cis-β-ocimene in citronella grass
essential oil. They also reported the absence of α-pinene, eugenol, α-cubebene, Germacrene-D, δ-
cadinol, γ-cadinene, δ- cadinene and β-caryophyllene in lemongrass essential oil [8].
3. Common methods for extraction of citronella grass and lemongrass essential oils
Lemongrass essential oil can be obtained from various extraction methods, such as solvent extraction,
ultrasound-assisted extraction (USAE), steam distillation (SD), hydrodistillation (HD), microwave-
assisted hydrodistillation (MAHD), and supercritical fluid extraction (SFE) employing carbon dioxide
(CO2). Because the quality of lemongrass essential oil is largely depending on its biochemical
constituents, the extraction techniques have been proven to significantly influence the yield and quality
of lemongrass essential oil [12-13]. In addition, extraction methods involving heating may trigger the
occurrence of remarkable thermal degradations or hydrolysis of thermally sensitive constituents.
3.1. Solvent extraction
In a solvent extraction (SE) system, a hydrocarbon solvent (usually n-hexane, petroleum spirit, alcohol
or their mixture) is mixed with the selected plant material to leach the essential oil out at a given
temperature or boiling point of the solvent. After separating the solution from the plant matrices and
concentrating the solution by distillation or evaporation, and leaving substance containing resin
(resinoid) or a combination of wax and essential oil remains. Although this method is simple and
adequately efficient to extract essential oil from lemongrass [14], it usually needs large quantity of
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
4
solvent and results in low yield reproducibility. In addition, contamination of the essential oil by residual
solvent is inevitable.
Figure 1. Solvent extraction with
Soxhlet apparatus [15-16].
Figure 2. Ultrasound assisted solvent
extraction with Soxhlet apparatus [16]
Solvent extraction of essential oil from lemongrass usually employs Soxhlet apparatus (Figure1)
[15]. This apparatus facilitates continuous contact between plant material and refluxing liquid solvent,
which leads to increase extraction efficiency. Unfortunately, it requires a long heating period at high
temperature (usually near to the boiling point of the solvent) which may trigger the thermal degradation
of thermally sensitive constituents. Solvent extraction either by maceration and Soxhlet extraction needs
an appropriate solvent to achieve a high extraction yield and to avoid the loss of volatiles. Lately,
Alhassan et al. had successfully extracted essential oil from dry and fresh lemongrass leaves using n-
hexane as solvent, which achieved 1.85% and 4.5% oil yield, respectively [15]. The physicochemical
properties of the essential oil are not altered because no constituent’s decomposition take place. This
solvent extraction method can also be performed at high pressure.
3.2. Ultrasound-assisted extraction
As a response to the increasing of awareness reduce greenhouse gas emissions and energy costs, food
and plant-based chemical industries are driven to look for new technologies that require low energy
consumption, investment and operating cost, meet legal environmental requirements, possess excellent
product/process safety and control to achieve high quality products [16]. In the last few decades, these
drawbacks have strengthened the use of advanced and efficient extraction methods compatible to
automation such as ultrasound-assisted extraction (UAE) (Figure 2). Shorter extraction times and lower
organic solvent consumption, energy and total costs, were the main issues to be achieved. Motivated by
these objectives, advances in ultrasound-assisted extraction have achieved numerous innovations to the
more established Soxhlet extraction, Clevenger hydrodistillation, continuous packed bed extraction
system, and some hybrids of ultrasound with other extraction methods such as microwave, extrusive,
and supercritical fluid extractions.
Sonochemical effects of ultrasound in a liquid are attributed to the acoustic cavitation phenomena
[17]. In the ultrasound field, acoustic cavitation generally refers to bubble formation, growth and
implosion occurring during the propagation of an ultrasound wave in a liquid media [ 18]. The
propagation of an ultrasound wave through an elastic medium induces a succession of compression and
rarefaction phases, which results in a longitudinal displacement of those constitutive molecules. At a
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
5
sufficient high intensity of a sound wave, during a rarefaction phase the attraction forces between them
might be exceeded, forming a cavity in the liquid as cavitation bubbles [19]. The cavitation bubbles can
grow due to coalescence, and/or rectified diffusion [20] as the vapor or gas dissolved in the medium will
enter the bubble during rarefaction phase and will not fully be removed during the compression cycle.
When acoustic cavitation bubbles collapse near and onto the surface of a solid material and produces
high-speed jets of liquids into the surface and creates shockwave damages [17]. These effects lead to
fragmentation of friable materials and localized erosion, which finally improve the reactivity of the
media and enhance mass transfer of solid particles due to tremendous particle size reduction.
High power ultrasonic probes are usually selected for extraction processes. The probes system
provides higher power than the ultrasonic bath as a result of intensive delivery of ultrasonic wave
through a smaller surface of the probe tip end). They are commonly operated at around 20 kHz and
employ transducer bonded to the probe, which is immersed into the extraction chamber resulting in a
direct delivery of ultrasound in the extraction media with lower loss of ultrasonic energy. Kimbaris et
al. have conducted that the application of ultrasound for essential oil extraction from garlic and found
significant reduction of the degradation of thermal-sensitive molecules, compared to HD [21].
Schaneberg & Khan also noted that ultrasound-assisted n-hexane extraction resulted in lemongrass
essential oil with comparable main compounds composition to steam distillation [14]. Ultrasound
intensity (power and frequency), shape and size of ultrasonic chamber, solvent and temperature are the
main influential parameters of the ultrasound-assisted extraction of essential oil [16].
3.3. Steam distillation
Steam distillation (SD) has been regarded as the most common method applied for the extraction of the
lemongrass essential oil, because it is simple and low investment cost [22]. In a steam distillation system
(Figure 3), steam continuously flows through the fresh or dried plant material, which softens the oil-
bearing cells of the parenchyma tissues and eases the essential oil to drift in the form of vapor. The
essential oil containing steam is then cooled in a condenser and the condensate is collected. Although
the steam temperature should be high enough to enable the vaporization of the essential oil, too high
steam temperature may lead to the destruction the plant material and/or remarkable decomposition of
important constituents of the essential oil. The continuous flow of the steam enables this extraction
process to be performed at a temperature close to 100°C under atmospheric condition, which is
considerably below the boiling point(s) of the individual constituent(s) of the essential oil that mostly
higher than 200°C [23].
Aromatic grass plant materials can be distilled either as fresh or wilted. Wilting herbaceous materials
prior to distillation process reduces the moisture content and leads to enhance the oil yield [5]. The
yields of the essential oil achieved from steam distillation of lemongrass were reported to vary from
0.24% [24], 0.3% [25], 0.6% [26], to 0.71% [27]. Steam distillation remains being the most preferred
method for the extraction of essential oil from lemongrass compared with other methods. Even, the
newer extraction method, such as the promising sub and supercritical carbon dioxide extractions will
not impend this simple distillation technique due to their high investment cost.
3.4. Hydrodistillation
In the hydrodistillation (HD) technique, the plant material is perfectly submerged in the boiling water
with continuous supply of direct heat (Figure 4). As a result, the essential oil jointly distills with water
molecules and then is sequestered after condensation. Similar to steam distillation, this method is also
easy to operate and requires low investment cost. However, the process is very slow, which may cause
serious degradation of some important compounds following hydrolysis or polymerization reactions of
sensitive components with regard to long exposure time to heat. In general, the oil yield largely depends
on many parameters such as the size, weight and the nature of the raw material and volume of water
used. Generally, the HD of lemongrass essential oil is performed in a boiling flask with total reflux or
Clevenger-type apparatus for a few hours following to the method suggested by Guenther [28].
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
6
Figure 3. Conventional steam
distillation apparatus.
Figure 4. Conventional
hydrodistillation apparatus.
Figure 5. Microwave assisted
hydrodistillation apparatus.
There has been variation of the yields of the essential oil obtained from HD of lemongrass leaves and
stalks. The yields were reported to range between 0.43% [29] to 1.80% [13]. Ajayi et al. noticed that the
pH of the water used for essential oil extraction from lemongrass leaves using HD remarkably affect the
essential oil composition [30]. They observed that the total yield of the volatile fractions obtained from
HD and microwave-assisted hydrodistillation (MAHD) using neutral water were 0.73% and 0.64%,
respectively. On the other hand, the total yield of the volatile fractions obtained from HD employing
weakly acid and weakly basic water were reported to be 0.7% and 0.45%. The contents of citral in the
essential oil obtained from HD, MAHD, acid-distillation and base-distillation were identified to be
72.6%, 44.7%, 30.07%, and 78.61%, respectively. In addition, considerable differences of major
components (geranial, neral, myrcene) contents were also noticed. The chemical transformations of
citral that was possibly occur in an acidic solution could be the cause of its low concentration [30]. The
presence of aldehyde moiety in citral, which can react with hydroxyl group of other terpenoids in the
existence of acid molecules to form acetals. Furthermore, other reactions, such as polymerisation,
disproportionation, cyclisation, are also likely to happen. As a conclusion, basic distillation medium
facilitates best environment for the extraction of lemongrass essential oil with a high citral content.
3.5. Microwave-assisted hydrodistillation
The working principle of microwave-assisted hydrodistillation (MAHD) is notably equal to
conventional HD. However, MAHD employs microwaves to heat up the solvent (Figure 5). The boiling
flask containing the solvent (usually water) and the plant material are introduced to a controllable
microwave oven (commonly operated at 2.45 GHz). The utilization of microwaves power speeds up the
essential oil extraction, which can be accomplished in a few minutes and leads to shorten the time
required to achieve the same amount of extracts.
This method is very interesting for both laboratory and industrial scale applications due to its efficient
heating, rapid energy and mass transfer rate, and being environmentally benign. The essential oil yields
obtained from MAHD and HD methods were reported respectively to be 0.35% and 0.2% [31].
Therefore, this method also receives wide acceptance as a potential and promising alternative to
conventional essential oil extraction techniques due to close similarity of the chemical composition of
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
7
the essential oils obtained. The MAHD also exhibited its superiority over the conventional HD on the
composition of major components (geranial, neral, myrcene) of the essential [12]. They reported that
MAHD method resulted essential oil with citral content of 93.28%, while citral content of essential oil
obtained from HD was 83.85%.
3.6. Supercritical fluid extraction
Over the last few decades, the augmenting requirement for premium quality natural products has
supported to the establishment of more environmentally benign method of essential oils extraction,
which is supercritical fluid extraction (SFE) [32]. The basic SFE unit comprises high-pressure pump,
water bath heater or oven, extraction vessel, microfilter, ball valves, back pressure regulator, cold trap,
volumetric gas quantifier, and vent (Figure 6). When cosolvent is required, another high-pressure pump
and mixer should be added to the basic SFE unit. This method can be considered as a promising
alternative to solvent extraction of valuable components for pharmaceutical and food applications from
various botanical matrices without any harmful traces of solvent [33]. The solvation properties of
supercritical fluid can be altered through the adjustment of temperature and pressure, which initially
changes its density and subsequently allows selective extraction. Carbon dioxide is most common
utilized supercritical fluid due to its excellent physicochemical properties, mainly related to its relatively
low critical temperature and pressure (23 – 50ºC and 8 – 12 MPa, respectively) [34]. Being a generally
recognized as safe (GRAS) status by Food and Drug Administration of the United States, CO2 is a non-
toxic, non-corrosive, non-flammable, and inexpensive gas. It has GRAS status [32].
Figure 6. Supercritical fluid extraction apparatus. [32]
Al-Marzouqi et al observed that the essential oils extracted from herbaceous matrices using SFE are
of a much better quality than those obtained using SE or SD and HD [35]. SFE with CO2 can be carried
out at temperatures about 30ºC, thereby taking care of the pristine composition and properties of the
essential oil. Unfortunately, the high investment cost of the equipment is reported to be one of the main
limitations of this method, which restricts its application for exceptionally special industries where high
quality and purity of the end products are of the outmost priority. Hitherto, only few reports can be
obtained in literature on extraction of lemongrass essential oil with supercritical CO2. Generally, the
studies are targeted to optimize the extraction process through the adjustment of temperature and
pressure, flow rate of the solvent, solvent mixture composition and raw material’s particle size. Carlson
et al. performed supercritical CO2 extraction of fresh lemongrass leaves under different temperature and
pressure conditions; and found that the composition of the essential oil significantly affected by
temperature and pressure [34]. The highest yields and extraction rates were examined at 9 MPa & 23ºC
and 12 MPa & 40ºC, which were 1.7% and 1.51%, respectively. The major components present in the
essential oil obtained from all the studied conditions were neral and geranial, which ranged from 26.7%
to 31.9% and from 44.6% to 53.0%, respectively. Marongiu et al. also investigated the influence of
pressure (9, 10, 11 and 12 MPa) on the supercritical extraction of lemongrass at 50°C for 360 min to
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
8
maximize citral content in the extracted essential oil [29]. They determined the highest yield (0.65%)
and the highest citral content in the essential oil (68%) at 9 MPa, while HD allowed achieving process
yield of 0.43% and citral content of 73%. The visual appearance of the essential oil changed at higher
solvent density; the color altered from yellow to yellowish semi-solid products due to the co-extraction
of higher molecular mass components. Wu et al. predicted the optimum operational parameters of the
supercritical CO2 extraction of lemongrass essential oil using response surface methodology [12]. They
found that SCCO2 extraction at 25 MPa, 35ºC, CO2 flow rate 18 (L/h) for 120 min resulted in 4.4%
yield. The main components (geranial and neral) of the essential oil obtained from the SFE were higher
than those of HD. However, the geraniol content in the essential oil obtained from SFE was lower than
that of HD. Although, the experiments were conducted for various species of lemongrass, it was proven
that the SF did not alter the main components of the essential oil.
Most recently, Yen and Lin develop a greener technique for the extraction of essential oil from
lemongrass using solar energy. Surprisingly, the yield of essential oil obtained from this technique
(1.28%) was very close with that obtained from HD (1.3 %) [36]. In addition, the essential oil obtained
from this method also exhibited a higher antioxidant activity than that extracted from HD. Therefore,
this new technique offers high potential application as future’s sustainable green extraction method.
4. Industrial applications of citronella grass and lemongrass essential oils
As a result of back to nature concept in the recent decades, the use of plants extracts has gained steady
increase of attention from customers leading to a promising commercial market, which comprises
perfumery, pharmaceuticals, cosmetics, and food applications, mainly due to their beneficial active
substances [1]. For millennium, lemongrass (C. citratus) essential oil has been used as traditional folk
medicine in the treatment of nervous, gastrointestinal disturbances (common stomach ache, digestive
problems and diarrhea), fevers and hypertension. In addition, lemongrass essential oil is also used an
important folk remedy for cough, flu, consumption, gingivitis, headache, ophthalmia, leprosy,
elephantiasis, malaria, pneumonia and other vascular disorders. Lemongrass essential oil has been
regarded as carminative, powerful insect repellent herbicides and food preservative [37]. Studies the on
extract from C. citratus leaves have demonstrated to be anti-inflammatory, vasorelaxing, diuretic and
effective remedy in treating ringworm as local application [38]. The essential oil from C. citratus leaves
may become highly attractive to the pharmaceutical industry, as most recent research has demonstrated
that citral exhibits selective toxicity for specific cancer cells [39]. Therefore, quality of this essential oil
is judged by the amount of citral present in the oil [40-41]. Essential oil, isolated from the leaves of
lemongrass, possesses a wide range of biological activities like antimicrobial, antifungal, anticancer,
and antioxidant properties [41].
Citronella grass (C. nardus) leaf and stalk are popularly used in domestic and professional cooking
as well as for the preparation of functional tea for its unique flavor. Citronella grass essential oil is
widely used in the food, drink, perfumery, soap, body and healthcare products and pharmaceutical
products [42]. It is also applied in the treatment of orthopedics, muscular and skin problems [10]. Recent
scientific studies have proven that citronella grass exhibited several biological activities, such as
antiviral, antibacterial and insect repellent [43]. The Chinese also utilize the essential oil of citronella
grass leaves more specifically for the treatment of rheumatism, fever, intestinal parasites, digestive and
menstrual problems. The essential oil of citronella grass leaves has been effectively employed as a
diaphoretic, stimulant, and promoter of internal detoxification by encouraging sweating [44]. In
Thailand, the infusion of citronella grass essential oil has been functioned in folk medicine as a blood
tonic and diuretic, and to cure flatulence, stomach ache, gastritis, intestinal cramps, irritable bowel, and
indigestion [9]. However, only very few reports are available on the analgesic effect and African
comparative study of chemical compounds of essential oil of this plant. Commercially, citronella oil is
isolated to obtain three important constituents, namely citronellal, citronellol, and geraniol, which are
popularly used for their antiseptic properties and perfumes and fragrances [45].
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
9
5. Conclusion
There is a steady increase of public interest in the application of the essential oil of aromatic grasses (C.
nardus and C. citratus) in the food and pharmaceutical fields. The oil contains various phytochemicals
such as terpenes, terpenoids, alcohol, esters, and phenolic compounds, which correspond to numerous
biological activities, such as antibacterial, anticancer, antifungal, insecticide, etc. A lot of studies have
performed to develop efficient methods for aromatic grass essential oil extraction and purification, and
assuring its quality with reasonable price. Prior to commercial scale applications, techno-economic
studies have to be accomplished to ensure the feasibility of the extraction methods and utilizations of
the essential oil. In general, aromatic grass essential oil can be considered as a valuable botanical product
that potentially attract the existing and future aromatic grass growers and users.
Acknowledgement
The authors greatly acknowledge the Faculty of Engineering - Universitas Diponegoro, Indonesia for
its partial financial support through Annual Activity and Budget Plans (RKAT) 2020 under Strategic
Research Grant 2020.
References
[1] Baser K H C and Buchbauer G 2015 Handbook of Essential Oils: Science, Technology, and
Applications (Boca Raton: Taylor and Francis Group).
[2] Tajidin N E, Ahmad S H, Rosenani A B, Azimah H, Munirah M 2012 Afr. J. Biotechnol. 11(11)
2685 – 93
[3] Suroso S 2018 Budidaya Serai Wangi (Cymbopogon nardus L. Randle) (Yogyakarta: Dinas
Kehutanan dan Perkebunan Daerah Istimewa Yogyakarta).
[4] Ganjewala D and Luthra R 2010 Nat. Prod. Commun. 5 (1) 163 – 72
[5] Skaria B P, Joy P P, Mathew G, Mathew S and Joseph A 2012 Lemongrass. In K.V. Peter (Ed.),
Handbook of Herbs and Spices vol. 2, ed K V Peter (Cambridge: Woodhead Publ. Ltd) pp.
348 – 70
[6] Hanaa ARM, Sallam Y I, El-Leithy A S and Aly S E 2012 Ann. Agric. Sci. 57 (2) 113 – 6
[7] Kumar V Tewari R and Singh K 2015 J. Essent. Oil-Bear. Plants 18 (3) 744 – 50
[8] Chanthai S, Prachakoll S, Ruangviriyachai C and Luthria D 2012 J. AOAC Int. 95 (3) 763 – 72.
[9] Barbosa L C A, Pereira U A, Martinazzo A P, Maltha C R A, Teixeira R R and Melo E D 2008
Molecules 13 (8) 1864 – 74
[10] Verma R K, Verma R S, Chauhan A and Bisht A 2015 J. Essent. Oil Res. 27 (3) 197 – 203
[11] Shaikh M N, Suryawanshi Y Ch and Mokat D N 2019 J. Essent. Oil-Bear. Plants 22 (2) 477– 83
[12] Desai M A and Parikh J 2015 2014 ACS Sustainable Chem. Eng. 3 (3) 421– 31
[13] Wu H, Li J, Jia Y, Xiao Z, Li P, Xie Y, Zhang A, Liu R, Ren Z, Zhao M, Zeng Ch and Li Ch
2019 Anal. Methods. Chem. 8192439
[14] Schaneberg B T and Khan I A 2002 J. Agric. Food Chem. 50 (6) 1345 – 49
[15] Alhassan M, Lawal A, Nasiru Y, Suleiman M, Safiya A M and Bello N 2018 ChemSearch J. 19
(2) 40 – 4
[16] Chemat F, Rombaut N, Sicaire A G, Meullemiestre A, Fabiano-Tixier A S, Abert-Vian M 2017
Ultrason. Sonochem. 34 540 – 60
[17] Moshonas M G and Shaw P E 2007 J. Agric. Food Chem. 18 509 – 12
[18] Kentish S and Ashokkumar M 2011 The physical and chemical effects of ultrasound Ultrasound
Technologies for Food and Bioprocessing, ed H Feng, G Barbosa-Canovas and J Weiss (USA:
Springer USA) pp. 1 – 12
[19] Mason T J and Lorimer J P 2002 General Principles Applied Sonochemistry: Uses of Power
Ultrasound in Chemistry and Processing ed T J Mason and J P Lorimer (Germany: Wiley-
VCH) pp. 25 – 74
[20] Ashokkumar M 2011 Ultrason. Sonochem. 18 864 – 72
International Conference on Chemical and Material Engineering (ICCME 2020)
IOP Conf. Series: Materials Science and Engineering 1053 (2021) 012118
IOP Publishing
doi:10.1088/1757-899X/1053/1/012118
10
[21] Kimbaris A C, Siatis N G, Daferera D J, Tarantilis P A, Pappas C S and Gubicza M G 2006
Ultrason. Sonochem. 13 54 – 60
[22] Fernandes S S, Tonato D, Mazutti M A, de Abreu B R, Cabrera D D, DOca C D M, Prentice-
Hernandez C and Salas-Mellado M D 2019 J. Food Eng. 262 200 – 8
[23] Berk Z 2013 Distillation Food Process Engineering and Technology, ed Z Berk (Amsterdam:
Elsevier Inc.) chapter 13 pp. 329 – 52
[24] Anggraeni N I, Hidayat I W, Rachman S D and Ersanda 2018 AIP Conf. Proc. 1927 UNSP039997
[25] Santin M R, dos Santos A O, Nakamura C V, Dias B P, Ferreira I C P and Ueda-Nakamura T
2009 Parasitol. Res. 105 (6) 1489 – 96
[26] Boukhatem M N, Kameli A, Ferhat M A, Tayebi K and Saidi F 2014 J. Consum. Prot. Food Saf.
9 (1) 13 – 21.
[27] Kpoviessi S, Bero J, Agbani P, Gbaguidi F, Kpadonou-Kpoviessi B, Sinsin B, Accrombessi G,
Frederich M, Moudachirou M and Quetin-Leclercq J 2014 J. Ethnopharmacol. 42 (3) 279 –
87
[28] Guenther E 1950 The Essential Oils IV (New York, USA: D. Van Nostrad company. Inc.) pp
2065
[29] Marongiu B, Piras A, Porcedda S and Tuveri E 2006 Nat. Prod. Res. 20 (5) 455 – 9
[30] Ajayi E O, Sadimenko A P and Afolayan A J 2016 Food Chem. 209 262 – 6.
[31] Tran T H, Nguyen D C, Phu T N N, Ho V T T, Vo D V N, Bach L G and Nguyen T D 2019
Indones. J. Chem. 19 (4) 1000 – 7
[32] Kumoro A C, Hasan M and Singh H, 2010 Arabian J. Sci. Eng. 35 (2) 7 – 16
[33] Haloui I and Meniai A H (2017 Int. J. Hydrogen Energy 42 (17) 12912 – 19
[34] Carlson L H C, Machado R A F, Spricigo C B, Pereira L K and Bolzan A 2001 J. Supercrit.
Fluids 21(1) 33 – 9
[35] Al-Marzouqi A H, Rao M V and Jobe B 2007 J. Liq.Chromatogr. Relat. Technol. 30 (4) 463 – 75
[36] Yen H Y and Lin Y C (2017). Ind. Crops Prod. 108 716 – 21
[37] Cassel E and Vargas R M F 2006 J. Mex. Chem. Soc. 50 126 –9
[38] Dama G Y, Tare H L, Gore M S, Deore S R and Bidkar J S 2011 Int. J. Pharm. Bio. Sci. 2 (1)
321 – 7
[39] Dudai N, Weinstein Y, Krup M, Rabinski T and Ofir R 2005 Planta Med. 71 484 – 8
[40] Nakahara K, Alzoreky N S, Yoshihashi T, Nguyen H T T and Trakoontivakorn G 2003 Jpn. Int.
Res. Center Agric. Sci. 37 249 – 52
[41] Mu’azu K, Ganiyu A, Alkali A S, Inuwa B, Ahmed A U, Jibia S M, Shehu M and Adamu I U
2019 Niger. J. Technol. 38 (2) 376 – 83
[42] Wei L S and Wee W 2013 Iran. J. Microbiol. 5 (2) 147 – 52
[43] Adibah A B, Faizah H, Hanina M N, Nazlina I and Ahmad I B. 2009 Malays. Appl. Biol. 38 (2)
73 – 5
[44] Pangnakorn U, Kanlaya S and Kuntha C 2011 Adv. Environ. Biol. 5 477 – 82
[45] Suslick K S and Price G J 1999 Ann. Rev. Mat Sci. 29 295 – 326