ArticlePDF Available

Synthesis and Characterisation of ZnO-Ag Thin Films and Their use as Ammonia Sensors

Authors:
Mohammed Bandr Abdullwahed at University of Anbar
Mohammed Bandr Abdullwahed
Ahmed Mishaal Mohammed at University of Anbar
Ahmed Mishaal Mohammed
Firas Fadhel Ali at University of Anbar
Firas Fadhel Ali
Download full-text PDFDownload full-text PDF
Read full-text
Download citation

Abstract and Figures

Abstract This study involves the preparation of colloidal silver (Ag) nanoparticle solution using Turkevich method. Specifically, the solution is mixed with the zinc nitrate hexahydrate and hexamethylenetetramine solution with various volume ratios (e.g. 50, 70 and 90 AgNPs %V) to deposit zinc oxide (ZnO)–Ag thin films on glass substrates at 350 °C using chemical spray pyrolysis technique. Then, these thin films are used to measure the sensitivity of ammonia (NH3) at room temperature (30 °C–32 °C). The thin films formed by this technique have been characterised by the following measurements: FE-SEM, XDR, AFM and EDXA; whereas, AFM, UV-Visible spectrophotometer and FT-IR spectrophotometer have been used to characterise the prepared Ag nanoparticles. The average size of ZnO–Ag nanoparticles formed on glass substrates is within the range of 68.93–86.64 nm, whereas the average size of Ag nanoparticles formed through Turkevich method is 48.9 nm. The XRD measurements show the wurtzite hexagonal and face centred cubic crystal structure of ZnO and Ag, respectively. The thin film that contains 50 %V of Ag has the highest gas sensitivity (69%). The high sensitivity of the ZnO–Ag sensor at room temperature is an indicator of the high efficiency of NH3 gas sensing.
Figures - uploaded by Mohammed Bandr Abdullwahed
Author content
All figure content in this area was uploaded by Mohammed Bandr Abdullwahed
Content may be subject to copyright.
٢٠٢٠١٠٣٠_٠٧١٥
٠٢.pdf
Content uploaded by Mohammed Bandr Abdullwahed
Author content
All content in this area was uploaded by Mohammed Bandr Abdullwahed on Oct 30, 2020
Content may be subject to copyright.
٢٠٢٠١٠٣٠_٠٧١٥
٠٢.pdf
Content uploaded by Mohammed Bandr Abdullwahed
Author content
All content in this area was uploaded by Mohammed Bandr Abdullwahed on Oct 30, 2020
Content may be subject to copyright.
A preview of the PDF is not available
... One approach involves using plants to create nanoparticles that serve as stabilizers and reducers, contributing to their compatibility with living organisms. This method represents a promising approach for medical applications [14][15][16]. Biological syntheses utilize natural resources like plants or bacteria, minimizing environmental impact and producing biocompatible materials [17][18][19]. Plant-mediated nanoparticle synthesis serves as a stabilizing and reducing agent. ...
View
Development of Ag/ZnO nanorods and nanoplates at low hydrothermal temperature and time for acetone sensing application: an insight into spillover mechanism
Article
Full-text available
  • Dec 2019
Nanostructure synthesis at low temperature with high purity and yield has a great potential in the present competitive research and development of nanomaterials for varieties of application. Here, we demonstrate the facile hydrothermal synthesis of ZnO nanocomposites at low hydrothermal temperature and time. With barely 80 °C hydrothermal temperature and 2 h of reaction time, ZnO nanorods were successfully synthesized, while by slightly increasing the reaction time (6 h-and-on), nanoplates of the same material were developed. Both the obtained nanostructures were analyzed using physio-chemical characterizing tools and examined for practical relevance as gas sensing material. The optimized sample was further treated to Ag loading (1–5 mol%) for lowering the operating temperature of the sensor. ZnO sample with 3 mol% Ag loading showed excellent sensitivity of 92.7% for 1000 ppm of acetone concentration with a drop in the operating temperature from 325 °C (Pristine ZnO) to 250 °C (Ag-loaded ZnO). The morphological correlation with reaction time and thereby sensitivity and spillover mechanism are discussed. Graphic abstract Open image in new window
View
Eco-friendly approach in synthesis of silver nanoparticles and evaluation of optical, surface morphological and antimicrobial properties
Article
Full-text available
  • May 2019
Silver nanoparticles (Ag NPs) were synthesized using Alternanthera sessilis leaf and Oregano root extract in an eco-friendly fashion and their significant physicochemical and optochemical properties were ascertained for nano-defined characteristics. The UV–visible spectrum showed a single and distinct absorbance peak at 433 nm (Alternanthera sessilis) and 425 nm (Oregano), typical SPR (surface plasmon resonance) for silver. Structural studies revealed nano-crystal with face centre cubic (FCC) symmetry with monodispersed nature. SEM studies showed spherical-shaped particles and the purity determined from EDX spectrum. The synthesized Ag NPs showed that antibacterial activity was studied. There was a significant inhibitory effect toward clinically important pathogens viz. B. subtilis, S. aureus, P. aeruginosa, and E. coli exposed to Ag NPs at different concentrations. Graphic abstract Open image in new window
View
Impact of silver nanoparticles on plant growth, some biochemical aspects, and yield of fenugreek plant (Trigonella foenum-graecum)
Article
Full-text available
  • Dec 2019
Abstract Background The use of nanotechnology can ensure food security via improving crop production. Nanoparticles have the ability to enhance growth and yield of different plants such as fenugreek (Trigonella foenum-graecum) (Fabaceae). The present work aims to study the role of silver nanoparticles (AgNPs) on growth, some biochemical aspects, and the yield both quantitatively and qualitatively of fenugreek plant. AgNPs were synthesized by chemical reduction of silver nitrate with trisodium citrate. Results Foliar application of AgNPs with different concentrations (20, 40, and 60 mg/l) improved the growth parameters of fenugreek plant (e.g., shoot length, number of leaves/plant, and shoot dry weight) and increased some biochemical aspects such as photosynthetic pigment (chlorophyll a, chlorophyll b, and carotenoids) and indole acetic acid (IAA) contents thus enhanced the yield quantity (number of pods/plant, number of seeds/pod, weight of seeds/plant, and seed index) and quality (carbohydrate%, protein%, phenolics, flavonoids, and tannins contents) of the yielded seeds as well as increasing antioxidant activity of the yielded seeds. Conclusion The most effective treatment was 40 mg/l as it caused the highest increases in the studied parameters.
View
Optical and Piezoelectric Properties of Mn-Doped ZnO Films Deposited by Sol-Gel and Hydrothermal Methods
Article
Full-text available
  • Feb 2019
  • J NANOMATER
Nowadays, multifunctional materials are of high interest due to their ability to be used in different applications by controlling one or two parameters (e.g., morphology and/or dopant). Zinc oxide is an intensive-studied material because of its large usability. Recently, we have shown that the conduction, transparency, and charge carrier concentration of ZnO can be controlled by changing the dopants, leading to promising materials as transparent conductive oxide films. In this work, sol-gel (SG) and hydrothermal (HT) methods were used separately or in combination in order to obtain ZnO films doped with Mn (1, 2, and 5%) for possible application in transparent optoelectronics or as piezoelectric materials. The manganese (Mn) dopant in the form of anhydrous manganese acetate was used to obtain Mn-doped ZnO films. ZnO hydrothermal (HT) growth was made on a previously ZnO seed layer, formed by sol-gel method. The Mn-doped ZnO films were deposited on microscope glass and on Pt/Ti/SiO 2 /Si substrates. A comparative characterization of the films for their structure, morphology, and optical and piezoelectric properties was achieved. SG films exhibit equiaxed nanoparticles, with diameters around 50 nm, while the films prepared by HT show a homogeneous morphology consisting of uniform 1D nanorods, sized about 30 nm diameter and 200–300 nm length. XRD diffractograms evidenced the presence of zincite phase (wurtzite structure hexagonally close packed), with an improvement in crystallinity of the HT films (compared with SG ones), which present a stronger tendency to be oriented along (002) plane (c-axis) at 2% at Mn. Spectroscopic ellipsometry shows that the films obtained by SG are much thinner than the ones obtained by HT and that the refractive index is increasing with the percent of dopant. The band gap energy was found to decrease with the Mn doping level from 3.28 eV (undoped ZnO) to 3.10 eV (ZnO doped with 5 at% Mn) for the samples deposited on Pt/Ti/SiO 2 /Si. The maximum transmission is found for the undoped ZnO film and decreases with Mn concentration but remains over 78% in the visible range. From the piezoelectric tests, it was found that the d33 coefficient is much larger for the HT samples in comparison with the SG samples, especially for 2 and 5 at% Mn. The optical and piezoelectric results could be of interest for applications in optoelectronic or piezoelectric devices.
View
View
High Sensitivity of NO Gas Sensors Based on Novel Ag-Doped ZnO Nanoflowers Enhanced with a UV Light-Emitting Diode
Article
Full-text available
  • Oct 2018
An ultraviolet-enhanced (UV-enhanced) nitric oxide (NO) sensor based on silver-doped zinc oxide (ZnO) nanoflowers is developed using a low-cost hydrothermal method. The results indicate that silver (Ag) ions were doped into the ZnO nanostructure successfully, thus changing the morphology. In the high-resolution transmission electron microscopy images, we also found that some Ag ions were separated out onto the surface of the ZnO nanoflowers and that the Ag-doped and Ag nanoparticles improved the sensing property. The NO sensing property increased from 73.91 to 89.04% through the use of a UV light-emitting diode (UV-LED). The response time was approximately 120 s without the UV-LED, and the UV-enhanced Ag-doped ZnO nanoflower sensor exhibited a reduced response time (60 s). The best working temperature could be reduced from 200 to 150 °C using UV light illumination, and it was found that the NO response increased by 15.13% at 150 °C. The UV photoresponse of the Ag-doped ZnO nanoflowers and the mechanisms by which the improvement of NO sensing property occurred through the use of UV light illumination are discussed. The property of the gas sensor can be calibrated using a self-photoelectric effect under UV light illumination. These interesting UV-enhanced Ag-doped ZnO nanoflowers are viable candidates for practical applications.
View
Ammonia Gas Detection Using Fabricated Zinc Oxide (ZnO) Nanoparticles on Glass Tube Substrates
Article
Full-text available
  • Aug 2018
This study aimed to determine the ammonia (NH 3 ) gas sensing ability of zinc oxide (ZnO) films deposited on glass tube substrates via successive ionic layer adsorption and reaction (SILAR) technique. The fabricated films were annealed at different temperatures. The sensor films were exposed to different volumes of ammonium hydroxide (NH 4 OH), converted to parts per million (ppm). The change in voltage from concentrations 595ppm up to 1189ppm exhibited a linear trend. However, no trend was revealed in concentrations 2378ppm and 3964ppm due to film saturation. Results showed that the films annealed at 250 °C, 300 °C, 350 °C, and 400 °C presented sensitivities of 2.7×10 ⁻⁴ V/ppm, 1.0×10 ⁻⁴ V/ppm, 2.3×10 ⁻⁴ V/ppm, and 1.5×10 ⁻⁴ V/ppm with R ² values of 0.997, 0.994, 0.904, 0.999 and resolutions of 3.7 ppm/mV, 9.9 ppm/mV, 4.4 ppm/mV, and 6.6 ppm/mV, respectively. Furthermore, this research study had proven that high quality gas sensors may be fabricated at a lower cost.
View
Oxford Desk Reference: Toxicology
Article
  • Jun 2014
Overdose and poisoning are one of the most frequent acute medical presentations seen in emergency departments, and high dependency and intensive care facilities. The Oxford Desk Reference: Toxicology provides an authoritative guide for the management of patients with poisoning. Each chapter includes key clinical features and potential treatment options to help physicians to assess the potential severity of the poisoned patient and provide the optimum clinical care. Information is easy to find and assimilate, and topics are self-contained to aid quick diagnosis.
View
High‐Temperature Gas Sensors for Harsh Environment Applications: A Review
Article
  • Jun 2019
This review paper introduces various types of gas sensors operating at high temperatures and their mechanisms, which can provide solutions to gas sensor selection for harsh environment application. Most of the gas sensors are found to be functioning at moderate operating temperatures (<400°C) and only a few reports are available, which highlight gas‐sensing performance above 400°C. Therefore, the selection of a more reliable high‐temperature gas sensor is necessary and advantageous for applications in areas such as agricultural waste processes (such as pyrolysis processes), military facilities, nuclear power plants, and automobile industries. In this paper, three major parts have been conducted to address the importance of high‐temperature gas sensors and provide strategical solution for gas sensor selection. First, we have highlighted the application scenario and the sensing mechanism of various gas sensors operating at high temperature. Additionally, factors that affect sensing performance at moderate operating temperature have been investigated. Secondly, we have discussed the effect of material compositions, morphology of the nanostructures, and the use of dopants on sensing performance of high temperature gas sensors. Meanwhile, the catalytic nature of the sensing layer and temperature effect on chemisorption in oxide‐based sensors have been discussed meticulously. Lastly, future challenges including factors affecting various sensor performance, selection, and preparation of sensing materials operating at higher temperatures are explored systematically.
View
View