Content uploaded by David L. Carroll
Author content
All content in this area was uploaded by David L. Carroll on Feb 16, 2018
Content may be subject to copyright.
62nd JANNAF Propulsion Meeting (7th Spacecraft Propulsion), Nashville, TN, 1–5 June, 2015
DISTRIBUTION A: Distribution unlimited.
Work funded by NASA Glenn on contract NNX13CC64P.
© Copyright by authors. Paper Tracking # 4032
CubeSat High Impulse Propulsion System (CHIPS)
N. J. Hejmanowski, C. A. Woodruff, R.L. Burton, D. L. Carroll
CU Aerospace
Champaign, IL
J. M. Cardin
VACCO Industries
South El Monte, CA
ABSTRACT
The increasingly successful use of nanosatellites has made CubeSat an attractive form factor for a
number of missions that require both an attitude control system (ACS) and primary propulsion. The
CubeSat High Impulse Propulsion System (CHIPS), under development by CU Aerospace with partner
VACCO Industries, is designed to enable CubeSat mission operations beyond simple orbit maintenance,
including significant altitude changes, formation flying, and proximity operations such as rendezvous and
docking. CHIPS integrates primary propulsion, ACS and propellant storage into a single bolt-on module
that is compatible with a variety of non-toxic, self-pressurizing liquid propellants. The primary propulsion
system uses micro-resistojet technology developed by CU Aerospace to superheat the selected
propellant before subsequent supersonic expansion through a micro-nozzle optimized for frozen-flow
efficiency. The 1U+ baseline design is capable of providing an estimated 563 N-s total impulse at 30 mN
thrust using R134a propellant, giving an impulse density of 552 N-s/liter. The ACS is a cold gas, 4-
thruster array to provide roll, pitch, yaw, and reverse thrust with a minimum impulse bit of 0.4 mN-s. An
engineering prototype, with integrated pressure control, power control, and data logging, was extensively
tested in cold and warm gas modes on the University of Illinois thrust stand under a range of conditions.
This paper presents thrust and specific impulse data for the resistojet thruster using two different
propellants. Resistojet data include cold and warm gas performance as a function of mass flow rate,
plenum pressure, geometry, and input power.
1. INTRODUCTION
An emerging trend in the field of space exploration is the development and deployment of low mass
satellites, commonly referred to as micro-, nano-, or femto-satellites. These satellites are seeing
increasing use as a low-cost alternative to more traditional large-scale spacecraft, a notable example
being the CubeSat standard, and eventually as components in a durable, redundant satellite network.
Nanosats are designed for a life of 1-2 years. They often have body-mounted solar panels, which makes
them severely power limited, with usable specific power P/m of ~1 watt per kg of satellite mass (note that
the Lockheed-Martin A2100 bus used for geosynchronous satellites has 4000 W capability and a launch
mass of ~3000 kg, so the 1 W/kg rule of thumb holds over a wide range of satellite masses). CubeSats
are also volume limited (1 liter per cube), placing a severe volume constraint on the propulsion system.
Nanosats are a low-cost, easily replaced approach to satellite constellations, and as such need to be
nimble. That is, orbital maneuvers need to be accomplished relatively quickly to minimize mission control
costs and maximize the usable satellite duty cycle of 1-2 years. Although rapid orbital maneuvering can
DISTRIBUTION A: Distribution unlimited.
2
always be accomplished by chemical propulsion, scaling down chemical systems to nanosat size (thrust
<< 1 Newton) has proved difficult for solid and liquid propulsion systems. Thus, one impediment to wide
implementation of nanosats is the lack of a highly compact, simple, and efficient propulsion system for
primary (orbital transfer, drag makeup, and maneuvering) and secondary (attitude and trajectory control)
applications. CHIPS eliminates this impediment by providing an integrated solution for both primary
propulsion and attitude control, enabling nano-, micro-, and even larger satellites to perform various
mission tasks including orbit transfer, de-orbiting, station keeping, and position, attitude and acceleration
control for multiple satellites in formation.
2. BACKGROUND AND DISCUSSION
NANOSATELLITE THRUSTER CHOICES
An important question for nanosatellites is: what range of efficiency and specific impulse are
appropriate for a nanosat electric micropropulsion system? TRL 9 EP systems have flown with efficiency
η (%) and specific impulse Isp (s) including the pulsed plasma thruster (10%, 1000 s); the resistojet (50-
80%, 300 s); the Hall thruster (50%, 2000 s); and the ion thruster (70%, 3000 s). Other EP systems in
advanced development are the colloid thruster; and the FEEP thruster. Propulsion selection for nanosats
depends on the propulsion capability, expressed in terms of the maneuver time and the required orbital
maneuver expressed in terms of ΔV, and also on the mass and volume available for the propulsion
system on the nanosat.
Burton et al. [Burton, 2010] introduced an equation for a constrained maneuver time that showed ΔV
varying inversely with Ue; a priori, this is counterintuitive because high ΔV interplanetary missions typically
utilize high specific impulse systems. The conclusion is that, in order to minimize orbit transfer times,
more maneuver capability is available for propulsion systems with low exhaust velocity and specific
impulse. To insist incorrectly on a high specific impulse is to incur a long time to perform the maneuver or
to limit the ΔV capability of the nanosat.
Clearly, the maneuver time t is a fundamentally important parameter. The question then is what
maneuver time is appropriate?
Because we are dealing with low-cost
nanosats with limited design life (1-2
years) in a rapid response environment,
it is not useful to have maneuver times
of weeks or months and their
associated delayed response, high
mission control support costs and
satellite downtimes. It is more
reasonable that the time to perform a
maneuver should be measured in days.
Figure 1 illustrates some typical values
of ΔV per day for a maneuverable
nanosat, as a function of Isp. We
assume that ηφ ~ 0.50 (where φ is the
power fraction Pp/P, defined in terms of
the propulsive power Pp, and the
maximum nanosat bus power P
produced by the solar panels), P/m ~ 1
W/kg, and that the desired time for a
single maneuver is 1.0 days.
As discussed by Burton et al.
[Burton, 2010], the “sweet spot” for
nanosat orbital maneuvers (shaded
region) appears to be in the 70 – 400 s
range of Isp, where ΔV is relatively large
Fig. 1. Operating envelope for nanosat propulsion. Maneuver
time is one day, requiring high thrust and reducing specific
impulse to the electrothermal range.
DISTRIBUTION A: Distribution unlimited.
3
but the fuel fraction is reasonably small, Fig. 1. For 50 s, typical of cold gas thrusters, ΔV is high but fuel
fraction is too large. For 2000 s, assuming a 50% efficient Hall thruster, the ΔV per day is only 4.3 m/s; for
3000 s, assuming a 50% efficient ion thruster, the ΔV per day is only 2.9 m/s; and for a 6000 s FEEP
thruster, the ΔV per day is only 1.5 m/s. These latter ΔV values are too small to be useful in time-
constrained maneuvers. The colloid thruster could eventually be considered assuming significant
improvements in efficiency and system volume.
We note that a nanosat propulsion system can operate from batteries. For a 5 kg, 5 W nanosat
operating for one day, the required energy is 432 kJ = 120 W-hr. Lithium-ion batteries of this size would
have a mass of about 1 kg, or 20% of the satellite mass, making battery operation possible, but requiring
a large fraction of the total nanosat mass. Batteries could be used in conjunction with photovoltaic cells to
increase power and decrease maneuver time, effectively providing φ > 1.
Unlike low power ion and Hall thrusters, which incur a large efficiency penalty from their neutralizers,
electrothermal thrusters in principle can operate at high efficiency at low Isp. The reason that ion and Hall
thrusters need high Isp to be efficient is that the exhaust is fully ionized, so that the kinetic energy of the
exhaust must be large compared to the energy required (ion cost) to ionize the xenon propellant. Low
power electrothermal thrusters on the other hand have no inherent requirement for ionized propellant,
which can be operated with an ionization fraction of zero for the resistojet.
The conclusion from this discussion is that the best specific impulse range for nanosats is relatively
low, in a range favoring electrothermal thrusters, Fig. 1.
PROPELLANT SELECTION
Propulsion performance is critically dependent on the propellant choice. A number of propellants have
been considered for CubeSats, including isobutane (C4H10), nitrous oxide (N2O), propane, ammonia,
hydrazine, peroxide, refrigerants (R134a), etc. [London, 2010]. CU Aerospace executed a study of 350
candidate propellants for the CubeSat/nanosatellite propulsion application, and down-selected to 9
candidates. Selection is based on the following criteria, Tables 1 and 2. (Note that SO2 has also
previously been denoted as EP-13.)
Table 1: Criteria for best candidate nanosatellite propellants.
Criterion
Justification
Favorable for
Not favorable for
High liquid density ρ
max propellant mass and ΔV
Water, SO2, R134a, R236fa
NH3, N2O, C4H10
High ρ x sound speed
max ΔV
H2O, N2H4, SO2, NH3, R134a,
R236fa
SF6, N2O, C4H10
Low heat of vaporization
low propellant heater power
SO2, R134a, R236fa
H2O, N2H4, NH3
Self-pressurizing
simplifies feed system
SO2, NH3, R134a, R236fa
H2O, N2H4, N2O
Critical temperature >60°C
liquid between 0°C and 60°C
H2O, SO2, NH3, R134a,
R236fa
N2H4, SF6, N2O, C4H10
Low freezing point
liquid between 0°C and 60°C
SO2, NH3, R134a, R236fa
H2O, N2H4
Compatible with materials
& electronics
Enables location of electronics
inside storage tank
R134a, R236fa, C4H10, SO2
H2O, NH3
Overall Selection
Optimizes Propulsion System
R134a, R236fa
H2O, N2H4, NH3, SF6,
N2O, C4H10, SO2
Because both cold and warm gas could be used, the primary selection criterion is the product ρa of
liquid density and sound speed at 300 K, or equivalently the product of liquid density and maximum cold
Isp, Table 2. A secondary criterion is the propellant heat of vaporization.
The third criterion is self-pressurization capability, which eliminates the need for a separate
pressurization system, saves mass and volume, and therefore increases propellant mass and impulse.
Propellants are selected with sufficient vapor pressure at 0ºC and modest pressure at 60ºC to avoid
excessive tank wall thickness and mass (note that thicker tank walls can significantly reduce propellant
volume in the small tank sizes necessitated for CubeSats). Propellants with a critical temperature below
60ºC (SF6, N2O, C4H10) are avoided because the initial tank fill must be low to avoid over-pressurization at
60ºC.
DISTRIBUTION A: Distribution unlimited.
4
Table 2: Comparison of product of liquid density and 90% of maximum Isp at 500°C for nanosatellite
propellants.
Propellant
Mol.
Weight
(g/mole)
Density
(g/cm3)
Isp at 500°C &
90% Nozzle Eff.
(s)
Density x Isp
(g-s/cm3)
Issues
H2O
18
1.002
155.1
155.4
Freezes @ 0°C, low vapor pressure
N2H4
32
1.008
116.3
117.2
Toxic, Freezes @ 2°C
SO2
64
1.381
82.2
113.6
Manageable Low toxicity
NH3
17
0.609
159.5
95.2
High P @ 60°C, thick structure
R134a
102
1.225
65.1
79.8
None
R236fa
152
1.373
53.4
73.3
Low vapor pressure @ 0°C
N2O
44
0.785
99.2
77.8
Critical temperature < 60°C
SF6
146
1.374
54.4
74.8
Critical temperature < 60°C
C4H10
58
0.579
86.4
50.0
Low liquid density, Tcritical < 60°C
The fourth criterion is materials compatibility with the feed system, thruster and with the control and
power electronics. This capability provides a volume-efficient way to package electronics, inside the
propellant tank, while providing waste heat to maintain propellant pressure and temperature while
evaporating. Testing studies performed by CU Aerospace have identified materials for electronics and
valves that are compatible with R134a, R236fa and SO2.
Finally, freezing is a concern for a tank temperature of 0ºC for H2O and N2H4, requiring that this risk
be mitigated by thermal management and propellant heating. These two propellants, despite high ρa, are
also contraindicated by high heat of vaporization and low self-pressurization. Because nanosatellites are
generally power limited, the additional heater power required during lengthy LEO eclipse times could
significantly impact these nanosatellites. Of the investigated propellants, the three most appealing for the
CubeSat operating temperature range of 0 – 60 °C are R134a, R236fa and SO2. Note that R134a and
R236fa are widely used, and SO2 was formerly used, as commercial refrigerants. The non-toxic, inert and
stable nature of R134a and R236fa tip the scales in their favor, making them an ideal green propellant for
future CubeSat missions.
3. CHIPS DESIGN
The CubeSat High Impulse Propulsion System, Fig. 2, is a complete nanosatellite propulsion solution
offering a high-performance micro-resistojet for primary propulsion and 3-axis cold gas attitude control.
Building on experience from prior nanosat propulsion product development, CHIPS integrates all
necessary propulsion subsystems into a bolt-on unit, including control and power processing units,
resistojet and ACS thrusters, frictionless micro-solenoid valves, tankage, maintenance systems and
software. System set-points, status, and firing telemetry are accessible and configurable through an RS-
422 serial interface. The CHIPS baseline propellant is R134a: a self-pressurizing, non-toxic and inert
refrigerant in widespread commercial use (R236fa having slightly lower total performance is a good
secondary option).
Fig. 2. Rendering of baseline 1.0U+ CHIPS flight
system showing locations and orientation of the
main and ACS thrusters. The propellant tank and
optional energy reservoir are included in the
structure
DISTRIBUTION A: Distribution unlimited.
5
The baseline 1.0U+ system, targeted at 2U - 6U CubeSats, occupies 1020 cm3 of total volume and
takes advantage of the “hockey puck” space available in the CubeSat PPOD. The 95 mm x 95 mm cross
section maximizes propellant load while leaving clearance for other CubeSat subsystems such as solar
panels. The CHIPS design allows for modifications based on customer-specific mission requirements: the
propellant tank may be reduced to as little as 0.5U or expanded to any desired length, tank width is
readily customizable, and the thrusters can be repackaged should the hockey puck volume be
unavailable. The optional 8.7 Wh energy reservoir included in the baseline allows the user to specify the
bus power load (as little as 1 W) during propulsive maneuvers.
CHIPS RESISTOJET
At the core of CHIPS is the high-efficiency micro-resistojet, the
superheater cartridge (SHC), Fig. 3. Resistive heating is accomplished
by passing current through the small-diameter, thin-walled “superheat”
tube which feeds the supersonic micro-nozzle. The superheat tube has
been optimized to minimize losses due to thermal conduction and
radiation. A coaxial shroud further reduces radiation losses while
protecting the superheat tube during handling and transportation.
Extensive testing of the SHC has demonstrated a consistent
performance in both warm-fire and cold-fire modes, resulting in a total
impulse of 563 N-s at 82 s specific impulse, and a maximum impulse
density of 552 N-s/liter, Table 3. Impulse density (also known as volumetric impulse) has been shown to
be a good metric (figure of merit) for propulsion system capability and degree of system integration in
nanosatellite-class spacecraft that are also volume limited [Hargus and Singleton, 2014].
Table 3. Performance specifications of CHIPS primary propulsion in warm and cold-fire modes at nominal 40
mg/s flow rate. Delta-V and Total impulse performance is based on a 1.0U+ baseline.
Parameter
Warm Fire Only
Cold Fire Only
Unit
Thrust
30
19
mN
Total impulse
563
323
N-s
Impulse density (total impulse / sys. volume)
552
317
N-s/liter
Delta-V capability (4 kg CubeSat)
155
89
m/s
Specific impulse
82
47
sec
Maximum continuous thrust time
20
60
min
Minimum impulse bit
---
0.5
mN-s
CHIPS ACS MODULE
The cold gas thrusters of the CHIPS
ACS module are located to provide 3-axis
stabilized control of satellite attitude when
coasting and steering during ∆V
maneuvers, Fig. 4. Four cold gas thrusters
(BCDE) are equally spaced on the
manifold; during ∆V maneuvers they
provide a nominal 24 mN of continuous
thrust at 47 sec Isp and can be pulsed to
provide a 0.4 mN-sec minimum impulse
bit, imparting a CubeSat velocity of 100
µm/s. The primary thruster is located such
that its 30 mN thrust vector (82 sec Isp)
passes through the CubeSat geometric
Fig. 4. Thrust vector diagram depicting both primary and
ACS thrusters
Fig. 3. SHC prototype.
DISTRIBUTION A: Distribution unlimited.
6
center. When fine adjustments are desired, the feed pressure set point can be tailored to provide a
minimum impulse bit as low as 0.18 mN-sec, Table 4.
For ∆V (X-axis) burns, the satellite is oriented so the X axis is in the desired direction of acceleration
using the attitude control mode, and the primary thruster is fired. Thruster pairs BE or CD are fired to
provide steering in yaw (about Z), and thruster pairs BC or DE provide steering in pitch (about Y), to
correct for any finite mismatch between the satellite CG and the primary thrust vector. For roll control
(about X), thruster pairs BD or CE are used. Initially, the random distribution of relatively dense liquid
propellant will cause the CG to be slightly misaligned with the thrust vector. However, as the burn
continues the propellant collects at the nozzle end, tending to stabilize the propellant CG along the thrust
vector. The internal geometry of the storage volume will naturally damp propellant slosh. For fine control
in X, thrusters BCDE are oriented 15 degrees below the Y-Z plane (Fig. 4), and are pulsed to provide +X
maneuvering, while the primary thruster is pulsed for –X maneuvering.
Table 4. ACS thruster specifications.
Parameter
Cold Fire
Unit
Notes
Max specific impulse
47
sec
Nominal
Min. Impulse bit
0.4
mN-s
∆V maneuvers, Est.
Min. impulse bit
0.18
mN-s
Fine maneuvers, Est.
Control authority
Roll, Pitch, Yaw, +X
CHIPS FUNCTIONAL DESCRIPTION
The schematic shown in Fig. 5 illustrates CHIPS functionality. The self-pressurizing propellant is
stored as a liquid in the integral storage tank, which includes a heater to maintain supply pressure when
CHIPS is near the lower operational temperature limit. When a firing sequence is initiated, the shutoff
valve is opened and propellant is drawn from the tank through a micro-heat exchanger feed dryer
designed to ensure no liquid reaches the vapor plenum. The in-situ CHIPS controller board actively
regulates plenum pressure via closed-loop control of the pressure control valve. Feed valves located in
the plenum control gas flow to their respective thrusters. All 7 valves in the CHIPS feed system are
normally-closed, frictionless soft-seat solenoid micro-valves from VACCO Industries. The propellant tank
and vapor plenum are welded against external leakage, and the feed system topology is designed to be
dual-fault tolerant against leakage to satisfy Air Force Space Command range safety user requirements
[AFSPCMAN 91-710].
Fig. 5. CHIPS schematic.
DISTRIBUTION A: Distribution unlimited.
7
The CHIPS baseline design includes an optional battery pack mounted in an enclosure on the rear
bulkhead of the propellant tank. Charger, maintenance, and survival electronics are integrated into
existing electronics which interface with the CHIPS controller board. In order for the battery pack to
supply power to CHIPS, the satellite bus must first activate CHIPS; this ensures that CHIPS will remain
powered off unless intentionally activated in order to satisfy common launch service requirements. The
battery pack enables high-performance ∆V maneuvers while allowing the mission to decide how much
power is supplied by the satellite bus via software (e.g. if bus power draw is set to 1 W, CHIPS can fire at
full power for 20 min before the pack must be recharged, giving ~9 m/s ∆V). Charge rate and timing is
also configured via software, allowing the customer to schedule charging around payload operations.
System Features
• Two operational modes:
o Warm gas mode for high specific impulse, large total impulse
o Cold gas mode for minimum or small total impulse maneuvers
• Control authority: roll, pitch, yaw, +/- X
• On-orbit update of system parameters, including:
o Thrust duration
o Plenum pressure (thrust)
o Superheater power level (specific impulse)
o Temperature & fault set-points
• Telemetry and status packets for system monitoring
• Dedicated propellant heater for continuous operation below +0°C ambient temperature.
• Propellant pressure sensor for closed-loop propellant temperature regulation.
• Propellant vaporizer ensuring 100% vapor delivered from liquid storage.
• High-reliability, frictionless valve propellant feed system
o VACCO micro-valves tested to 200,000+ cold gas firings
o Double-fault tolerant against leakage
• High-density, self-pressurizing R134a baseline propellant:
o Green, non-toxic, non-flammable & inert
o Chemically stable, high critical temperature, low freezing point & vapor pressure
Figure 6 shows an illustration of CHIPS in a standard CubeSat frame. CHIPS is highly adaptable to a
wide range of specific geometries and can be designed to accommodate different propellant tanks and
configurations.
Figure 6. Illustration of CHIPS in a CubeSat frame.
DISTRIBUTION A: Distribution unlimited.
8
4. EXPERIMENTAL RESULTS WITH CHIPS PROTOTYPE
EXPERIMENTAL SETUP
CHIPS thrust testing was performed in the University of Illinois at Urbana-Champaign (UIUC) Electric
Propulsion (EP) laboratory. Within the facility’s 1.5 m3 vacuum tank is an advanced thrust stand with 8 µN
resolution [Wilson, 1997]. Thrust stand measurements were taken with a background pressure of
approximately 400 milli-Torr. Windage effects [Whalen, 1987] artificially lower thrust readings, but the
correction is within experimental error and is not applied. A diagram of the CHIPS test apparatus on the
thrust stand is shown in Fig. 7.
Fig. 7. CHIPS test apparatus on UIUC thrust stand (note: the ETFE line is the propellant feed line).
When running on the thrust stand, the CHIPS test apparatus is fed by a propellant bottle (e.g. R134a)
external to the tank, and placed on a scale to determine the steady state mass flow rate. Note that
thermal mass flow meters proved inconsistent for measuring R134a flow rates. This is a result of the
saturated vapor phase propellant upstream of the pressure control valve along with the highly
temperature-dependent specific heat of R134a.
Functionally, the test apparatus only differs slightly from the flight configuration. For example, the
valve immediately following the vapor plenum is not present on the test apparatus. This makes short,
controlled bursts for minimum impulse testing impossible, but this capability exists in the latest prototype
hardware. In contrast, sustained, reliable superheater performance has been the major focus since the
start of the program, and this is accommodated by the configuration above. The feed dryer and tank
heaters are not used since the apparatus is gas fed from a source bottle. The aforementioned hardware
upgrade has a feed dryer and self-contained propellant tank. Finally, the results presented do not include
ACS thruster performance, as these thrusters have yet to be tested.
The CHIPS support board uses an onboard pressure sensor to measure and control the vapor
plenum pressure by operating the pressure control valve. In addition, the board provides a specified
amount of power to the superheater cartridge. Power and pressure measurements are recorded by the
board via a telemetry stream from the device. Conditions are controlled precisely enough to repeat flow
conditions, which has been a useful gauge on system health. Example pressure and power profiles for a
DISTRIBUTION A: Distribution unlimited.
9
typical thrust stand test are presented in Fig. 8 and Fig. 9. A long duration firing is followed by two brief
firings. The first burn is to acquire an accurate mass flow measurement for the given firing condition.
Tests performed with this apparatus consume at least 16 grams of propellant during this time, as the
scale’s resolution allows for less than 2% total error with this propellant quantity.
Fig. 8. Plenum pressure readings from CHIPS
support board during thrust stand test
Fig. 9. Power readings from CHIPS support board
during thrust stand test
Thrust measurements are most accurately taken at the beginning and end of a given firing, since the
stand can drift over time, and the on state is compared to the off state of the stand. This is why secondary
firings are performed after the first, longer burn. The thrust profile corresponding to Fig. 8 and Fig. 9 is
shown in Fig. 10. During thruster operation, the thrust stand voltage (TS Voltage) drops from its resting
voltage, ~7.5 V, to about 1.9 V. The full range of the thrust stand is calibrated before and after thrusting,
so the changes in voltage correspond to thrust values. Note that the overshoots during the activation of
the thruster are excluded from thrust measurements or mass flow rate measurements.
Fig. 10. Thrust stand voltage for sample thrust stand test
DISTRIBUTION A: Distribution unlimited.
10
EXPERIMENTAL DATA
Throughout the CHIPS program, there have been several design iterations on both the superheater
and its nozzle. These configurations predate the superheater cartridge, which neatly packages the
superheater, nozzle, electrical connections, and gas feed. Fig. 11 and Fig. 12 below show the latest
performance data for the CHIPS superheater cartridge.
Fig.11. Isp vs. specific energy for 37 mg/s R134a with
superheater cartridge design
Fig. 12. Thrust vs. pressure for 37 mg/s R134a with
superheater cartridge design (higher pressure
indicates higher power cases)
The thrust values shown in Fig. 12 correspond to the Isp points in Fig. 11, as the increased specific
energy increases the pressure required to maintain the baseline flow rate of 40 mg/s. As shown above,
the CHIPS micro-resistojet can exceed 80 seconds Isp with a specific energy of 0.8 J/mg. Note that this
case had an input power of 30 W with a mass flow rate of 37 mg/s. Mass flow rate for this case was lower
than anticipated for the pressure set-point due to increased heating by the superheater cartridge over
previous designs. Since the system is a pressure controlled system, there are variations in the mass flow
rate for each case, but this is accounted for by plotting against specific energy instead of power.
Alternate Propellant
R236fa, an alternative propellant option for CHIPS, was tested on an older test apparatus. With a
higher molecular weight, its nozzle performance is lower than R134a, but its increased liquid storage
density largely makes up for the disparity. The performance of the CHIPS micro-resistojet with R236fa is
compared with that of R134a in Fig. 13 and Fig. 14.
While this data is taken with slightly different flow conditions and a less refined apparatus, it highlights
the merits of R236fa as a propellant. The density x Isp product is indicative of the total impulse available
from a complete system, and R236fa nearly matches R134a with this metric. R236fa has a lower
operating pressure than R134a, which can be advantageous when there are additional safety concerns.
However, the lower pressure propellant requires more preheating and cannot achieve the same
performance as R134a, so it is not the baseline propellant choice for CHIPS.
DISTRIBUTION A: Distribution unlimited.
11
Fig. 13. Isp vs. specific energy for 25-30 mg/s R134a
and R236fa
Fig. 14. Density * Isp product vs. specific energy for
25-30 mg/s R134a and R236fa
EFFICIENCY
Taking the highest performance case, we can assess the losses in the superheater cartridge and
examine the efficiency of the system as a whole. By measuring the increase in temperature of the test
fixture which holds the superheater cartridge, the combined radiation and conduction losses of the
cartridge are calculated, Table 5.
Table 5. SHC Heat Loss Calculation
Term
Value
Comments
Test Fixture Mass [g]
364
6061 Aluminum block
Test Duration [s]
420
-
Delta T [K]
9
Temperature increased 9 K
Power to Fixture [W]
7
Assumes constant Cp of 0.896 J/g-K for aluminum
This testing was performed at the same operating condition as the highest performing case shown in
Fig. 10. Relevant parameters for this test case are shown in Table 6. Note that operation at the maximum
specific impulse requires high superheater temperatures, and thus losses are maximized at this condition.
Table 6. Top Performing SHC Case Parameters
Parameter
Value
Thrust [mN]
30.2
Isp [s]
82.0
Input Power [W]
30.0
Mass flow rate [mg/s]
37.1
Given the 30 W of input power and losses of 7 W, the heating efficiency of the SHC is ~77%. The
power required to evaporate R134a at the above flow rate is ~6.5 W. This means a low load on the tank
heaters and minimal spacecraft heating during firing. Total thrust efficiency can be calculated from the
terms above
η
!=!T!g0!Isp!/!2!P0. This results in a thrust efficiency of 40%. Considering the high molecular
weight of R134a, this is a positive result. With a lower molecular weight propellant this would be much
higher, but this is sacrificed for the total impulse capability of R134a and non-toxic, self-pressurizing
properties.
DISTRIBUTION A: Distribution unlimited.
12
5. SUMMARY AND CONCLUSION
Nanosatellites are a cost-effective alternative to large-scale spacecraft; the CubeSat form factor in
particular is increasingly utilized for a number of academic, commercial and government missions, but the
nature of the platform imposes severe power, mass and volume constraints which often force users to
forgo primary propulsion, limiting mission duration and on-orbit operations. The CubeSat High-Impulse
Propulsion System (CHIPS) provides an attractive solution to this problem by integrating 3-axis attitude
control with a high-impulse micro-resistojet primary propulsion system and supporting subsystems into a
bolt-on package. System volume is in line with typical reaction wheel + magnetorquer combinations for
nanosats, and the optional battery pack allows CHIPS to operate in power-limited systems.
R134a was selected as the baseline propellant for CHIPS because of its appealing characteristics as
a propellant and benign nature in comparison to other options such as hydrazine or sulfur hexafluoride.
Testing performed on the superheater cartridge (SHC) showed minimal losses with a heating efficiency of
77%. This allows for a maximum performance of 82 s Isp with 30 mN thrust at an input power of 30 W,
resulting in an estimated total impulse of 563 N-s for the 1.0U+ baseline system while requiring as little as
1 W from the bus power supply with the optional battery pack.
6. ACKNOWLEDGEMENTS
This work has been sponsored by the NASA Glenn Research Center under SBIR contract
NNX14CC04C. Heather Hickman served as the technical monitor and Eric Pencil served as a technical
advisor. Our thanks also to Kevin Bassett, Darren King, Laura Richardson, Jason Lee, and Scott Robins
for their assistance with different technical aspects of the program.
REFERENCES
Burton, R. L., Eden, J. G., Park, S.-J., de Chadenedes, M., Garrett, S., Raja, L. L., Sitaraman, H.,
Laystrom-Woodard, J., Benavides, G., and Carroll, D., “Development of the MCD Thruster for
Nanosat Propulsion,” JANNAF Conf., Colorado Springs, CO, Paper 1387 (2010).
Burton, R. L., Benavides, G.F., and Carroll, D.L., “Space Thruster Using Robust Microcavity
Discharge,” U.S. Patent Application No. 13/680,484 (2012).
Ghosh, A, Coverstone, V. “Study of Low-Thrust Trajectories for Low Orbit Multiple CubeSat
Missions,” AAS conference, paper no. 10-174 (2010).
Hargus, W.A., and Singleton, J.T., private communication (2014).
Laystrom, J.K., Burton, R.L., and Benavides, G.F., “Geometric Optimization of a Coaxial Pulsed
Plasma Thruster,” AIAA Paper 2003-5025 (2003).
London, A. P., and Droppers, L. J., “High-Performance Liquid Propulsion For CubeSats: Requirements
and Approaches,” JANNAF Conf., Colorado Springs, CO, Paper 1428 (2010).
Whalen, M.V., “Low Reynolds Number Nozzle Flow Study,” NASA-TM-100130 (1987).
Wilson, M.J., Bushman, S.S., and Burton, R.L., “A Compact Thrust Stand for Pulsed Plasma
Thrusters,” 25th International Electric Propulsion Conf., IEPC Paper 97-122, Cleveland, OH (1997).