PosterPDF Available

An in-depth view into the Tesla Model S module Part one: Single cell testing and modelling

March 2017

DOI:10.13140/RG.2.2.18373.96487

Conference: Kraftwerk Batterie 2017
At: Aachen, Germany

Authors:

Friedrich Emanuel Hust

Mercedes-Benz

Matthias Kuipers

Forschungszentrum Jülich

Heiko Witzenhausen

RWTH Aachen University

Pouyan Shafiei Sabet

FEV Europe GmbH

Show all 7 authorsHide

Several cells of a Tesla Model S Module after a usage of 25000 km are examined with respect to their electrical and thermal parameters. Also a short study on the influence of different currents during cycling is performed.

Content uploaded by Friedrich Emanuel Hust

Content may be subject to copyright.

A preview of the PDF is not available

ResearchGate has not been able to resolve any citations for this publication.

ResearchGate has not been able to resolve any references for this publication.

Sponsored content

"To lead my own group is a fantastic opportunity!" Clio Azina, Ph.D. is a new Junior Principal Inv...

January 2021

Cypriot Clio Azina came to RWTH in August 2020 as a Marie Skłodowska-Curie Fellow and is now a Junior Principal Investigator Fellow. We asked her about her start in Aachen in view of the coronavirus restrictions and her expectations for her time at RWTH. Welcome to RWTH Aachen University. We are...

Sponsored content

RWTH is inviting excellent and experienced early career researchers to apply for 6 Junior Principal...

November 2020

The program is designed to attract and support stellar researchers with international experience. Applications from women as well as others whose background and experience enrich the culture of the university are particularly encouraged. Support will be provided for a period of four years, with...

Sponsored content

Sun, Wind, and Power Trading

January 2018

Diverse causes behind frequency fluctuations in power grids The use of renewables like the sun and wind can cause fluctuations in power grids. But what impact do these fluctuations have on security of supply? To answer this question, scientists from Jülich and Göttingen worked together with...

Sponsored content

Finally Up and Running

August 2016

Silicon-air battery achieves running time of over 1,000 hours for the first time Silicon-air batteries are viewed as a promising and cost-effective alternative to current energy storage technology. However, they have thus far only achieved relatively short running times. Jülich researchers have...

Article

Topographically induced diurnal boundary layer oscillations: Two dimensional synoptic scale modeling

January 1979

D. W. McLawhorn

A two dimensional boundary layer model is developed for the study of diurnal cycles in boundary layer convergence over synoptic scale sloping terrain and thermally inhomogeneous surfaces. To properly resolve the terrain configuration, a local terrain following coordinate system is developed. The local coordinate system has characteristics which are superior to the terrain following coordinate ... [Show full abstract] systems commonly used. Truncation errors are significantly reduced in the local system so variations in the flow field due to physical forcing are easily discernible from those due to truncation error. The model exhibits a sensitivity to lattitude though it is apparently not very sensitive to radiative flux divergence calculations.

Article

Full-text available

Thermal test scheduling using constraint programming

January 2006

Temperature cycling test is one of the key stages in the process of testing circuit packs in telecommunications. To obtain a good overall test schedule requires that the thermal test is carried out efficiently i.e. with the minimum number of runs and valid configurations of packs at each run. However, finding valid configurations and building them into a minimal thermal test schedule is a ... [Show full abstract] difficult combinatorial problem. Constraint Programming allows both a way of modelling the rules of configuration and formulating a model to derive an optimal number of runs. We describe this model and the results obtained from it for a large multi-national telecommunications manufacturer. Copyright c2006 IFAC

Article

Modeling Solar Wind Variations over an 11 Year Cycle with Alfvén Wave Dissipation: A Parameter Study

April 2021 · The Astrophysical Journal

We study the behavior and properties of the solar wind using a 2.5D Alfvén wave (AW)-driven wind model. We first systematically compare the results of an AW-driven wind model with a polytropic approach. Polytropic magnetohydrodynamic wind models are thermally driven, while AWs act as additional acceleration and heating mechanisms in the AW-driven model. We confirm that an AW-driven model is ... [Show full abstract] required to reproduce the observed bimodality of slow and fast solar winds. We are also able to reproduce the observed anticorrelation between the terminal wind velocity and the coronal source temperature with the AW-driven wind model. We also show that the wind properties along an 11 yr cycle differ significantly from one model to the other. The AW-driven model again shows the best agreement with observational data. Indeed, solar surface magnetic field topology plays an important role in the AW-driven wind model, as it enters directly into the input energy sources via the Poynting flux. On the other hand, the polytropic wind model is driven by an assumed pressure gradient; thus, it is relatively less sensitive to the surface magnetic field topology. Finally, we note that the net torque spinning down the Sun exhibits the same trends in the two models, showing that the polytropic approach still correctly captures the essence of stellar winds. © 2021. The American Astronomical Society. All rights reserved..

Article

Influence of the parameters of temperature cycles on the cyclic fracture toughness of 5Kh3V3MFAS ste...

July 1998 · Strength of Materials

A. P. Gopkalo

We performed experimental investigations of the crack resistance of tool steel under conditions of nonisothermal loading and established the effect of the time of holding at the maximum temperature of thermal cycles on the critical size of a fatigue crack and cyclic fracture toughness.