Article

Non-destructive Examination of Multiphase Material Distribution in Uranium Hexafluoride Cylinders Using Steady-State Laser Doppler Vibrometery

Authors:
To read the full-text of this research, you can request a copy directly from the authors.

Abstract

The ability to detect the diversion of a significant quantity of nuclear material is the objective of international nuclear safeguards, and safeguarding uranium enrichment technology is especially important in preventing the spread of nuclear weapons. In gas centrifuge enrichment plants, the uranium is in the form of uranium hexafluoride (UF6), which regularly transitions between phases during processing and storage due to its low triple point. The variation of material distribution in Uf6 cylinders has a significant effect on enrichment measurement uncertainty, especially with increasing accuracy of passive neutron assay measurements, motivating interest in non-destructive methods of examining UF6 cylinder fill distributions. For this study, a novel steady-state scanning laser Doppler vibrometer (LDV) system is used to determine the material and phase distributions within small UF6 cylinders. This technology induces steady-state ultrasonic waves throughout an object and then uses a scanning laser to measure vibrational wavenumber at pixilated points on the object. Different materials and phases are excited by the ultrasonic waves to different extents, changing the local measured wavenumbers and allowing fill distributions of the storage cylinders to be mapped. Through non-destructive examination of the variation in typical fill profiles of UF6 cylinders, the uncertainty associated with neutron measurements of UF6 cylinders may be better characterized.

No full-text available

Request Full-text Paper PDF

To read the full-text of this research,
you can request a copy directly from the authors.

... Local wavenumber methods can then be applied to detect anomalies. Goodman et al. (2014) demonstrated this method to assess material distributions inside storage cylinders and achieved scan times of less than 10 s. similarly used continuous excitations to assess delaminations in composites, which reduced scan times from about 3 h to 10 min. ...
... Local wavenumber methods can then be applied to detect anomalies. Goodman et al. (2014) demonstrated this method to assess material distributions inside storage cylinders and achieved scan times of less than 10 s. similarly used continuous excitations to assess delaminations in composites, which reduced scan times from about 3 h to 10 min. ...
Thesis
Full-text available
This research explores almost entire speckle related techniques for large-area damage inspection. The fullfield vision-based LSI system was demonstrated and verified on a honeycomb composite plate and C-17 aileron composite stiffened panel using this proposed DPE algorithm under two classes of loading: (I) low frequency thermal stress loading (~Hz) and (II) high-frequency steady-state vibration in ultrasonic frequency range for large-area inspection in near real-time. The visualized damage images agreed with images from the baseline of pulse laser/LDV, ultrasonic C-scan and X-ray CT scan. The DPE algorithm has a promising potential to apply on any optical metrology for instantaneous phase estimation and is capable of combining with selected imaging conditions for multi-damages blind detection.
Conference Paper
Full-text available
An Advanced Damage Processing Network (ADPNet) was proposed with laser speckle photometry (LSP) employed in a non-contact, full-field, vision-based non-destructive inspection (V-NDI) system for large area multiple hidden damages detection under thermal excitation. In contrast to point-based non-destructive inspection (P-NDI) system employing laser Doppler vibrometer (LDV) with discrete wavefield captured by pointwise scanning, the V-NDI system captures the wavefield of at least an order higher spatial resolution by a CMOS camera for every time instance without repeating the experiment tens of thousand times to reassemble the wavefield where P-NDI does. The LSP/ADPNet system relies on observing the variation of laser speckles in time series without reference arm and is very insensitive to ambient noise where traditional holography/ESPI suffers greatly. Other advances of LSP/ADPNet system are its robust tolerance of laser coherence, larger illumination area, flexible choice of correlation functions, real-time processing on FPGA and more advanced post-processing techniques for ADPNet such as Bayesian updating/inference that can be readily applied.
Article
In plate-like structures, wall-thinning defects resulting from corrosion may not be accompanied by any indication of damage on the surface. Thus, inspections are required to ensure that wall-thinning defects are within allowable limits. However, conventional ultrasonic techniques require physical contact to the structure. Alternatively, acoustic wavenumber spectroscopy (AWS) may be used for detecting, locating, and characterizing defects. This paper describes the performance of AWS in the estimation of a wall-thinning defect size in thinplate structures using finite element analysis (FEA). Through a series of FEAs, the structure’s steady-state response to a single-tone ultrasonic excitation is simulated, and the wall-thinning defect-size effect on the wavenumber-estimation accuracy is investigated. In general, the A0 guided wave mode is widely used to visualize defects because of the nature of the wave speed variation in relation to the plate thickness. However, it is not appropriate for the detection of relatively shallow wall-thinning defects, because the rate of change in wave speed with the thickness decreases with increasing plate thickness. To overcome this limitation, we propose a method to optimize excitation frequency and effective guided wave mode instead of utilizing the A0 mode. The results can be used to determine the size of shallow wall-thinning defects in plate-like structures.
Conference Paper
Full-text available
We present an approach to visualize damage through rapid, full-field measurements of a plate-like st ructure's steady-state response to a single-tone ultrasonic excitation. In our setup, a piezoelectric transducer provides the excitation while a 2D scanning laser Doppler vibrometer (LDV) makes the full-field response measurement. In taking measurements of a structure's relatively high amplitude single-tone steady-state response, we enable significantly faster scans by avoiding many of the signal-to-noise ratio issues typical ly associated with LDV ultrasonic measurements. Damage is visualized by making automated estimates, on a pixel-bypixel basis, of the wavenumber of the excited response through wavenumber-domain pr oce ssing. We provide sample imaging results for hidden corrosion spots in a metallic plate and delamination in two composite specim ens.
Article
This paper describes a method to effectively image structural features and defects using local estimates of the wavenumber of propagating guided Lamb waves at a fine grid of spatial sampling points. The guided waves are rapidly excited at each grid point using a scanning Q-switched laser system and sensed by a single fixed ultrasonic transducer. Through reciprocity, this produces a full-wave-field time history of a virtual wave being excited from the transducer. Using frequency–wavenumber processing, localized wavelength estimates are obtained by isolating each wave mode, narrowband filtering to one or more high-energy frequency bands, and identifying the center-wavelength of a sliding wavenumber band-pass filter that maximizes the energy at each grid point. The approach was capable of producing detailed images of hidden wall-thinning in an aluminum plate and a steel pipe section and local impact delamination in a complicated composite component.
Article
Interim and long-term storage of carefully prepared plutonium material within hermetically sealed containers may generate dangerous gas pressures and compositions. The authors have been investigating the application of acoustic resonance spectroscopy to non-intrusively monitor changes in these parameters within sealed containers. In this approach a drum-like gas cavity is formed within the storage container which is excited using a piezoelectric transducer mounted on the outside of the container. The frequency response spectrum contains a series of peaks whose positions and widths are determined by the composition of the gas and the geometry of the cylindrical resonator; the intensities are related to the gas pressure. Comparing observed gas frequencies with theory gives excellent agreement. Small changes in gas composition, better than 1:1000, are readily measurable.
Metabolic fate and evaluation of injury in rats and dogs following exposure to hydrolysis products of uranium hexaflouride
  • Pe Morrow
A multisensor unattended cylinder verification station for uranium enrichment plant safeguards using passive neutron enrichment
  • D Goodman
  • Rowland K Smith