Conference PaperPDF Available

Project for a network of automatic stations for UFO monitoring

Authors:

Abstract and Figures

After presenting the past history of scientific methodology applied to UFO monitoring operations, a new project for an automatic station is presented and discussed. Some engineering issues are also presented to stimulate a pragmatic " problem solving " aptitude. The proposed idea is intended to be a basis of discussion concerning the implementation of a permanent station containing off-the-shelf measurement instruments that, being in function all the time, are able to acquire scientific data on unidentified flying targets, which are then transmitted to investigators located at remote areas. Such an automatic station is intended to be a pilot project for a future network of similar stations scattered throughout the territory. The physical parameters that can be obtained this way are conceptually presented. The main goal is to ascertain what the nature of the UFO phenomenon is and which physics can be extracted from it.
Content may be subject to copyright.
1
Project for a network of automatic stations for UFO monitoring
MASSIMO TEODORANI, Ph.D. Astrophysicist / UFOAC Consulting Scientist
with:
MARK RODEGHIER, Ph.D. Astronomer & Sociologist / CUFOS / UFOAC Scientist
RON MASTERS, Ph.D. Physical Chemist / UFOAC Consulting Scientist
PHILIPPE AILLERIS, UAP Observations Reporting Scheme / UFOAC Consultant
ABSTRACT. After presenting the past history of scientific methodology applied to UFO
monitoring operations, a new project for an automatic station is presented and discussed.
Some engineering issues are also presented to stimulate a pragmatic problem solving
aptitude. The proposed idea is intended to be a basis of discussion concerning the
implementation of a permanent station containing off-the-shelf measurement instruments
that, being in function all the time, are able to acquire scientific data on unidentified flying
targets, which are then transmitted to investigators located at remote areas. Such an
automatic station is intended to be a pilot project for a future network of similar stations
scattered throughout the territory. The physical parameters that can be obtained this way are
conceptually presented. The main goal is to ascertain what the nature of the UFO
phenomenon is and which physics can be extracted from it.
1. Introduction
The UFO phenomenon is mostly known for its testimonial character, for its great social
impact and for its random nature (Condon, 1969; Hendry, 1979; Hynek, 1972; Kean, 2011;
Sturrock, 1969; CUFOS website; Wendt & Duvall, 2008). Nothing of such a phenomenon is
predictable. Therefore no scientific treatment is apparently possible so far. The evaluation
of witness cases is typically subject to a series of errors due to a too subjective description
of persons who are most often emotionally involved from what allegedly happened to
them (Teodorani, 2009a). Testimonial data screening is often deficient in accuracy, while a
careful analysis of witness cases most often shows that reports of alleged UFO sightings
can be explained by natural or man-made phenomena. On one side photos or videos of
UFO events can be explained as well as prosaic phenomena (such as insects, birds or
airplanes in distance); on another side too many alleged videos and photos are hoaxes and
fakes. In most of the cases a photo and/or a video, taken alone, cannot be considered an
evidence to be taken seriously in order to carry out a scientific analysis. In the same way
marks left on the ground cannot be alone a proof of a “UFO landing”, unless such a
“landing” can be accurately documented. Chemical analysis of alleged ground samples is
not sufficient alone to prove the exogenous nature of an anomalous phenomenon.
2
Is it possible to carry out a scientific analysis of a UFO phenomenon? In principle, yes, it is.
The main point is that except for some very rare attempts based on testimonial cases
(Condon, 1969; Haines, 1980; Hill, 1995; Maccabee, 1999; NARCAP website; Rodeghier,
1981; Sturrock, 1999; Teodorani, 2009b; CUFOS website; UAPRS website; UAPSG website)
such an analysis is effectively possible only when data are taken using appropriate
scientific instrumentation (Bunnell, 2003; MLR website; ICPH website; PH website; PSI
website; Rutledge, 1981; Stephan et al., 2009; Strand, 1984; Teodorani & Strand, 1998;
Teodorani, 2004, 2009b, 2011) and when similar data can be compared together by
different observers. Anyway such an attempt has been only partial so far. A scientific fact
must bring investigators to deduce physical parameters, such as speed, luminosity and
distance, for instance. As luminosity of a flying target is a manifestation of an ongoing
physical process that involves the state of excitation and ionization of atoms, it is clear that
nocturnal lights are the most suitable cases that can be investigated scientifically. This can
be done by analyzing the behavior and surface distribution of the light of the aerial target
and of the spectrum of such a light in order to search and measure spectral lines and/or a
simple continuum spectrum (Kitchin, 2008; Lang, 2005). All of this is not clearly sufficient,
because what we see in the optical range might be only a fraction of the entire energy
spectrum. Therefore optical instruments must be necessarily coupled to sensors that
operate at different wavelengths, and where the detected radiation is not significantly
affected by our atmosphere. The infrared window is the best choice in this case, and in
some cases the ultraviolet window too. But the electromagnetic radiation that an energy
source is able to emit is even wider. If we exclude high-energy emission (such as X and
gamma-rays) that is easily absorbed by the atmosphere, we must necessarily consider the
very wide range of radio emission, in particular the UHF (microwaves, 1-30 GHz), VHF (30-
300 MHz), and VLF/ELF (3-30 KHz) ranges. In brief it is necessary to monitor the optical
phenomenon simultaneously (and not separately) with the electromagnetic field that it
possibly produces. As several reports exist about UFO phenomena that are able to produce
electromagnetic interference (Rodeghier, 1981; Maccabee, 1994; Meessen, 2012) it is also
necessary to verify if the local magnetic field is subject to disturbances that are temporally
correlated with such a phenomenon (Strand, 1984). Finally, the dynamics of the
phenomenon can be studied only if it is possible to deduce how the measured physical
parameters vary with time (Teodorani, 2000, 2001): in fact it is expected that the data that
one is able to acquire are spread along a certain period of time in which the phenomenon
produces its effects. If we have all of these essential data in hands we are then in a
condition to extract true scientific data, namely: data that, differently from the qualitative
nature of witness information, are quantitatively treatable in the form of pure numbers.
When we have all the numbers in hand (plus the associated error) we are then in a
condition to build charts of the several parameters that we can infer from the monitoring
operations, so that we are finally able to search for possible correlations between the
several measured parameters. Correlations can potentially bring us to the construction of
the physics of the observed phenomenon.
3
Crucial scientific information, using an automatic monitoring station, cannot be limited to
the case of so called “nocturnal lights” (Hynek, 1972; Hendry, 1979) but it must be also
extended to anomalous (often with structured shape) aerial phenomena that appear in
daylight. This is justified by one part of the UFO sightings that have been reported both in
the past and at the present time (Hendry, 1979). In such a specific case, even if optical
spectra cannot be obtained, we can obtain crucial data as well. For instance we can
simultaneously obtain high-quality videos of the aerial phenomenon and extremely
important data concerning the electromagnetic and magnetic field that is time-correlated
with it in case (Rodeghier, 1981; Meessen, 2012). Electrostatic measurements can be
carried out as well. And photographs and or videos might also show luminous spot-like
sources that are in case located on the extended surface of the target, which can be
accurately studied, especially their possible time variation and their possible correlation
with the speed parameter (Teodorani, 2001). Possible shape changes and their variation in
time, more probably due to magnetic refraction effects, can be studied as well using
optical devices.
Clearly only an appropriate scientific analysis of this kind (regarding both nocturnal and
daily lights) can permit one to ascertain if an alleged UFO phenomenon is a true anomaly
or if it can be explained and/or identified with a well-known manifestation. Therefore it is
more than evident that a healthy (certainly not dogmatic) skepticism is the only possible
aptitude that can help serious investigators to make a correct screening of the monitored
phenomena.
Apart from locations in the world in which the UFO phenomenon (in particular nocturnal
lights) seems to be constantly or occasionally recurrent (Teodorani, 2008), in most cases
UFO accidents occur randomly in space and time (Hendry, 1979; CUFOS website).
Therefore it is virtually impossible to use scientific personnel on field in order to obtain
measurements data using sensor devices. In order to solve possibly such an
unavoidable problem, it is inevitably necessary to install and use automatic and remotely
controlled stations that are equipped with measurement instruments that are able to
furnish the most essential physical parameters of the phenomenon.
2. Previous experience of instrumented UFO monitoring
Before discussing which are the optimal characteristics that an automatic monitoring
station should have, it is necessary to mention what has been done in the past using such a
methodology. More or less successful attempts have been done since the seventies. Let’s
mention the most important experience done on the instrumented monitoring of UFO
phenomena, just quoting some examples.
4
Project Starlight International (PSI) (PSI, website) is probably the first important attempt
to monitor UFO phenomena using measurement instrumentation that was located at a
station. It was founded in 1964 by technician and ufologist Ray Stanford, with the purpose
of gathering and disseminate a broad range of instrumented UFO data to
the scientific community. During its existence (years ’60 and ’70), the project has utilized
magnetometers, a gravimeter, radio spectrometer, radar, laser-telescope-video system,
and other electronic and optical systems for recording the physical effects, optical images,
and location of UFOs. The project conducted in-depth analyses of motion-picture films of
UFOs obtained by PSI staff members, along with magnetometric, spectrographic, and other
data recorded during UFO events. Apart from this such data have not directly produced
true scientific publications of academic level, but allowed anyway some academic
scientists to do this (Meessen, 2012). The choice of PSI instruments was certainly optimal
and complete, even if they were mainly aimed at monitoring UFOs under the preconceived
assumption that they are due to extraterrestrial visitation.
In the period of time 1973-1980 physicist Harley Rutledge of the Southeast Missouri State
University, together with his Ph.D. students, carried out a monitoring campaign in
Piedmont, Missouri, where suddenly a recurrent light phenomenon started to appear
sometimes very frequently. Telescopes, optical and radio spectrometers, and
magnetometers were used at that time with some occasional measurement and result,
together with detailed reports of the very many witnessed visual cases. In any fact such
first scientific instrumented attempt, although being tenacious, academically directed and
partially productive, couldn’t offer a truly systematic approach to the problem as no
automatic system was operating at that time. But this was a great trigger for the future of
scientific investigation of such phenomena. A very important book was published by
Rutledge (Rutledge, 1981).
Starting from 1984 a new project was born in Norway, thanks to electronic engineer Erling
Strand of Østfold College. That was “Project Hessdalen” (PH, website), aimed at monitoring
instrumentally typically unstructured plasma-like light phenomena that were reported very
often in Hessdalen, a very little village in central Norway. During only forty days an
instrumented measurement campaign was carried out very intensely in the winter of 1984
(Strand, 1984), bringing to very reliable results after using a magnetometer, a radio VHF
spectrometer, some telescopes, and many cameras equipped with a spectrographic grating
too. Such a campaign, probably the most important ever conducted in the world up to that
time, demonstrated that anomalous aerial phenomena, when recurrent, can be measured
indeed. From that time on, especially after a very important workshop occurred in spring
1994, the interest of the scientific community grew more and more and several important
academic papers have been published so far (Fryberger, 1997; Teodorani & Strand, 1998;
Zou, 1995). In the last 19 years Italian, US and French engineers and scientists have been
fruitfully involved in the project (ICPH, website; IEA, website; Project Hessdalen website;
5
Zlotnicki et al., 2012). The grown scientific interest at an international level allowed
Hessdalen researchers, to which electronic engineer Björn Gitle Hauge of Østfold College
was productively added meanwhile, permitted finally to build up a fixed station (PH,
website) where the following instruments were permanently installed: several
sophisticated videocameras, a magnetometer, two types of radar, a very advanced VLF-ELF
spectrometer and a microwave spectrometer. Compared to previous experience in other
areas of the world the peculiarity represented by the so called “Hessdalen Observatory”
was that it was the first attempt to make an automated station. It was used as such mostly
with the videocameras, which for a period of time of some years acquired continuously
video data, permitting to find some important evidence of the phenomenon. VLF-ELF data
were automatically recorded as well but their full analysis is still lacking. In the last years,
due to lack of funding and to problems of technical maintenance also because of
occasional bad weather, such a station is operational mostly only using simple streaming
cameras. The “Hessdalen Camp” initiative (born in the beginning of this century) was
another meritorious initiative (PH, website), in which the first steps of scientific method
applied to the Hessdalen mystery were taught very fruitfully to young students with the
stimulus of the phenomenon occurring in that area. The Hessdalen experience has globally
shown to be fruitful and even revolutionary, but in time, apart from the good “politics”
adopted in order to raise the interest of people, it showed some gaps from which everyone
should now learn in the perspective of future projects there and elsewhere in the world.
Such gaps might be probably resumed in the following points: a) problems with constant
money funding; b) difficulties of a constant and prompt maintenance during hardware and
software failure; c) lack of minimum competent technical personnel that is constantly on
site; d) much and good engineering and computer science work but little true experimental
and observational physics work (even if good non-Norwegian papers of theoretical physics
were published indeed by someone; [Fryberger, 1995]). Such gaps, which were and are
mostly due to practical difficulties and not just to human inefficiency, should teach us to
understand where and how it is possible to do better in future projects.
Other important, but more limited, monitoring projects on UFO and similar phenomena
(such as the so called “earthlights”) have been carried out by other very competent
scholars. Since 2003 the international group conducted by geophysicist Marsha Adams has
permitted to carry out several instrumented missions in USA and abroad using portable
instrumentation (IEA, website). The past experience of electronic engineer David Akers (in
the seventies, eighties and nineties) with his video and magnetic monitoring of anomalous
light phenomena occurring recurrently in the Yakima (Washington) area (Akers, website),
and of aerospace engineer James Bunnell in the Marfa (Texas) area are very reliable from
the professional point of view. In particular, during more recent monitoring work (this
century, up to now) Bunnell deployed and used very sophisticated optical instrumentation
such as telescopes, cameras, true spectrographs, and videocameras, the last ones being
automatically controlled inside two small permanent observing stations. Bunnell’s work
6
has allowed to obtain important physical information on what is occurring in Marfa and
several valuable papers have been published by him and by his academic collaborators
(Bunnell, 2003; MLR, website; Stephan et al., 2009). Geologist Bruce Cornet’s work in Pine
Bush (New York) during the nineties cannot be ignored as well due to his meticulous
monitoring work of that area of light phenomenon recurrence (often mixed up with
structured anomalous aerial objects) using magnetometers, videocameras, cameras and
sound sensors (Cornet, website). Important and original design of a quite sophisticated
UFO monitoring station is nowadays carried out by astronomer Eamonn Ansbro too, in
Ireland (Ansbro, 2004), where video, spectrographic and electromagnetic instruments are
implemented as a short-range version of the SETV experiment (Ansbro, 2001).
As it has been presented above, most of the instrumented systematic efforts have been
devoted to the study of Hessdalen-like lights (to be categorized as “nocturnal lights” in the
standard ufological nomenclature) as in several parts of the world this kind of
phenomenon (otherwise called “earthlights”) is much more frequent than more proper
“structured aerial objects” (which, in any fact, have been reported many times also at
areas of earthlight recurrence). But such an experience, from an instrumental point of
view, is of course perfectly suitable to monitor every kind of aerial phenomenon, and the
acquired experience and know-how has opened the door to this kind of investigation.
Therefore, in the light of the past experience what should be done in order to build up an
optimal automatic monitoring system aimed at future research projects?
3. Automatic measurement station
What are the characteristics that an automatic station should have nowadays in order to
obtain data that are able to satisfy a fully scientific procedure? The following points are
probably the most important ones to point out (see also Figure 2).
A. Optimal Power Sources. A station that works all the time without interruption, except
during maintenance, needs an efficient system that guarantees with reasonable
continuity its power supply. Being batteries unpractical for this specific use or, anyway,
of limited use in time, previous experience (PH, website) shows that long cables (with a
length of the order of 1800 feet) can be used quite efficiently. Therefore such a station
should be located at an optimal position, where an energy source is available (for
instance: a house that is not too far from the station). This logistical problem must be
accurately solved as the “battery option” is of very limited use in terms of time of
utilization and would require periodic and very frequent battery changes or recharge,
considering that more than one batteries should be used in order to serve several
instruments inside the station. Due to possible black-outs, which might be caused both
by bad weather and by the phenomenon itself (PH, website; Hendry, 1979), the cable
7
system for energy supply should be coupled to a continuity module, which is ready to
enter in function as soon as an energy failure occurs. A cable system is able to serve
simultaneously all the measurement instruments in only one hit.
B. Station Multiplicity. In order to cover wide areas of a country (such as USA, for instance)
it is inevitably necessary to implement several stations that are wisely spread in a
targeted way over the country. The project might be started with two or three stations
that are set up at strategic points of the country.
C. Effectiveness vs Costs. Due to the realistic availability of money funding and to the
necessity of simplicity of maintenance, each station must be equipped with essential
instruments that are both simple for use and at the same time sophisticated enough.
D. Range and Sensitivity. Every instrument that composes an automatically and remotely
controlled monitoring station must be able to detect weak signals (comprising all
wavelengths, ranging from radio to the ultraviolet if a complete system is used). This
increases the possibility to record light phenomena that are away from the station but
over the horizon. Typically such instruments should be able to detect and record signals
coming from sources that are at least 10 miles away from the station.
E. Instrument Completeness. Every station, which is exp ected to be a compact “box”,
must contain inside several instruments (see Figure 1). The most important instruments
that must be used are probably the following ones: one all-sky camera 1 (UWO website)
connected to a low or medium-high resolution spectrographic grating, one triaxial
fluxgate magnetometer 2, one electrostatic detector and one weather station. Such four
instruments should constitute a “basic unit”. An optical unit, which can be added and
connected to the basic one in a subsequent phase, should contain the following
instruments: one high-sensitivity videocamera for taking videos 3 (SOSO, website), one
1 All-sky camera. A good example is given by the system used by NASA for fireball research:
http://fireballs.ndc.nasa.gov/ A simpler but more dedicated system is represented by the “UFOCATCH”
platform: http://www.ufo-science.com/fr/telechargements/pdf/ufocatch.pdf
2 Magnetometer. A good example is given by the very portable and sophisticated MEDA fluxgate
magnetometer: http://www.meda.com/
3 Multiple Videocameras. Concerning the specific issue of videocameras an important point, due to Dr.
Ron Masters (Masters, 2013), should be made taking advantage of previous projects (Gröschel, website)
concerning the used frame rate and exposure times, where two videocameras are simultaneously used
with different rates (1/sec and 25/sec) to optimize signal to noise (S/N) ratio. Such a procedure could be
decided as an alternative to the basic videocameras present in the standard optical system proposed here.
This would allow one to use correct exposure times to obtain best S/N ratio for the UAP of interest in an
image frame. At the same time large dynamic intensity range would be gained so that dim and bright
objects can be selected from images and not be over or under exposed (Masters). A third high-resolution
system (camera or optical zoom) is needed (Masters’ idea) that responds to the image location observed by
the first two cameras to provide sufficient optical resolution to distinguish shape. This third camera system
8
high-sensitivity videocamera attached to a low-dispersion grating for optical
spectroscopy (Masters, 2012), one DSLR professional camera attached to a dispersion
grating for medium-high resolution of “echelle kind (Masters, 2012), one specialized
videocamera with the capability to record many frames per second 4 (high time-
resolution; typically: 10.000 fr/sec), one specialized DSLR professional camera for
infrared and ultraviolet photos 5, one optical radiometer. An “electromagnetic unit”,
which can be added and connected to the basic one in a subsequent phase, should
contain the following instruments: one spectrum analyzer for microwave-UHF signals 6
(plus antenna), one receiver/spectrometer (plus antenna) for VHF signals (PSI, website;
Strand, 1984), one receiver/spectrometer for VLF/ELF signals, one Geiger counter. A
large part of the described instruments can be chosen among several high-quality
models that are available on the market. All instruments must be computer controlled.
A gravimeter (which is typically much heavier and more expensive than all the other
instruments), a high sensitivity sound sensor and a thermal imaging camera might be
added to the station if money funding will permit in a subsequent phase. All of such
instruments must be of the off-the-shelf kind (namely: very portable, light and cheap)
and connected directly to a computer server where data can be constantly recorded and
then promptly downloaded from remote areas where investigators are located. The
station needs a periodic maintenance both for the proper functioning of the
instruments themselves and for an appropriate internet connection and efficiency.
Of course such a proposed instrument completeness, complexity and sophistication
must be balanced against the cost and the available power source to run the
instrumentation. But it should be reminded that the optical and the EM ones are just
optional units (although extremely important for an appropriate and more rigorous
physical study) that can be added only in a subsequent phase and only if results have
would use data from the first two cameras to point to the location of interest and set exposure conditions
to provide best ability to discern shape. This idea is similar to how global observatory networks provide
information to specific telescopes to point to an area of interest based on data obtained from other
telescopes, such as when a supernova or some other interesting event is detected. This camera could also
connect to a spectrograph (Masters’ idea). Many systems could be deployed in many locations using the
first two cameras. Hot spots could be equipped with the third system. Other types of detectors would be
added to the equipment as the rest of the team decides, perhaps initially at the hot spot locations, then
eventually to all locations.
4 High-speed videocamera. A good example is given by the very portable and sophisticated Olympus i-
SPEED : http://www.olympus-ims.com/it/hsv-products/
5 UV/IR DSLR camera. Probably the best example on the marked is represented by the Fuji FinePix S-3 Pro
UVIR : http://www.dpreview.com/news/2006/8/9/fujifilms3prouvir
6 Microwave spectrometer. One of the best portable spectrometers of this kind is represented by the
Aaronia Spectran : http://www.rtelecom.net/product/127/rf-spectrum-analyzer-1mhz-9-4ghz-spectran-hf-
xfr-aaronia.html
9
been previously obtained using the basic system in order to justify further money
funding. First one must be able to demonstrate that such a station is able to catch “UFO
data”, then all the good reasons would come in order to implement more sophisticated
instrumentation. Without considering the limiting factor per se in terms of time of
utilization, if a battery option is used as an energy source evidently if the number of
instruments increases the number of batteries must increase and the cost would
increase as well with them. That’s the reason why a battery system is not viable both in
practical and in economic terms. Past experience done with the Hessdalen station (PH,
website) shows that a cable system can be used indeed. Therefore much of all the
efforts should be concentrated in finding an existing appropriate power source in the
vicinity of the station itself or not too far from it.
Figure 1. Automatic Station. 1) UHF Spectrum analyzer, 2) VHF Receiver, 3 VLF/ELF Receiver, 4)
Geiger Counter, 5) Magnetometer, 6) All-Sky Camera, 7) Weather Station, 8) Electrostatic Detector,
9) Optical Radiometer, 10) High-Sensitivity Videocamera + Low-Resolution Grating, 11) High-Speed
Videocamera, 12) High-Sensitivity Videocamera (normal + night shot modes), 13) DLRS Camera +
Echelle Grating, 14) DLRS Camera, 15) UV-IR DLRS Camera, 16) Computer/Server, 17) Remote
Computers.
10
F. Alarm device. An appropriate alarm facility must activate all the instruments together.
Such a device might be constituted of a multi-instrument “EM box” 7 (able to
communicate with the computers that control all the main instruments) or of the all-sky
camera itself, which would be the only instrument that would presumably work all the
time.
G. Station Location Choice. On the basis of which criteria is the location of the stations
decided? Clearly maximum priority should be given where the incidence of UFO reports
is more frequent in the country. This can be evaluated through an accurate statistical
analysis (Teodorani, 2009b; The Canadian UFO Survey, website).
H. Scientific redundancy. Instruments to be deployed at the stations must be able to be
used for purposes that are also different from UFO monitoring. For instance, all of the
available optical sensors can be used to monitor (and measure) the passage of
meteors/bolides and fireballs in the sky and electric phenomena of the high atmosphere
such as Elves and Sprites. This already partially happened with the instrumentation used
during previous or current anomaly research (MLR, website; SOSO, website). All the
electromagnetic instruments might be able to monitor phenomena generated by
geophysical causes (such as tectonic stresses near faults), by meteorological factors
(storms in distance, atmospheric electricity), and by the activity phase of the Sun. Of
course, in order to allow the employed instruments to be useful for standard science
too, one will need to consult with various specialists to obtain their advice on what
measurements they would find useful, in what format and with what sensitivity. If both
needs (the study both of the anomalies and of natural phenomena) can match together,
one would reach a solid and efficient multiplicative factor as well as an attraction pole
for “standard” physical scientists, who indirectly (or even directly) might become
interested (and involved too, in case) in the study of aerial anomalies too, thus bringing
potentially the physical study of such kind of anomalies fully inside the academic
environment.
I. Station Flexibility. Due to some practical reasons, a monitoring station can be intended
in two distinct modes: a) as a permanently fixed station on ground; b) as a fully portable
station. In the first case the station, although fixed for use, must be easily transported
since it will have to be shipped to its final location, or shipped back for periodic
maintenance. This mode seems to be considered realistic today due to the rarity of
specific areas of USA (or Earth in general) in which aerial anomalies that show a
systematically structured shape suddenly occurs in the form of time “flaps” at several
locations (Hendry, 1979; CUFOS website). In the second case the station should be easily
moved elsewhere in case of necessity, typically in order to monitor continuously several
7 UFO Multisensor. A possibly useful “alarm device” might be represented by the “UFO Multisensor 1.0”:
http://digital-service.biz11.de/images/Dateien/c-Ufomultisensor%201-0%20englisch.pdf
11
recurrence areas where Hessdalen and plasma-like phenomena occur. Due to this such a
station should be placed over a little transportable wagon (equipped with wheels) to be
attached to a truck, and, in case, also transportable aboard a cargo airplane. A decision
on which of the two options must be adopted will depend on if one is more interested
in monitoring highly anomalous structured aerial phenomena of probable artificial
nature or if one is more interested in monitoring anomalous plasma-like phenomena of
possible (but not assured yet) geophysical nature. In the first case the probability to find
something is much lower than in the second case, but the importance to study
structured aerial phenomena is so higher than the importance to study probable
geophysical phenomena that the first mode should be chosen, also considering that
anyway an automated station that records data continuously at a fixed location is
expected to obtain results in time. This time in terms of probability of finding
something is much longer than for natural-like phenomena’s, but the much higher
importance to study structured phenomena (due to what it might involve) justifies the
fact that the first mode of making a station should be preferred to the second one.
J. Security against interference and intrusions. Stations must be placed at areas where no
electromagnetic interference occurs due to human devices and where natural magnetic
anomalies are not present. Therefore places that are isolated and safe at the same time
must be chosen, but with the fundamental compromise in mind that a power source of
the cable kind (located at an house, for instance) should be reasonably close to the
station (Kelleher & Knapp, 2005; PH, website). Such a vicinity in principle should render
the station much safer than if it is totally isolated (in which case a battery mode would
be necessarily used as a power supply). A constant but soft control of the cops should
be guaranteed too according to standard vigilance of houses, even the most isolated
ones. In any fact the area should be fenced and an appropriate tag should be attached.
As a permanent technician for the station’s periodic maintenance might be of basic
importance for the efficient and continuous functioning of the station, one could think
of such a collaborator on site (in case more collaborators who take periodic turns
among them) who momentarily is accommodated at the same house where the power
source is located for cable connections to the station. A similar mode (a private house
close to the Hessdalen station) has been adopted in the recent past in Hessdalen by
Italian engineers in order to allow the control of the radar screen. In such a specific case
the power source was located at another house.
K. Occasional presence of investigators. In the case that a “UFO flap” (not only earthlights)
occurs at a location whose contour (and/or “epicenter”) can be evaluated precisely and
that such a “flap area” is a typically long lasting one, the automatic station should be
placed there (Cornet, website). In such a case it would be highly recommendable that
some investigators are also present in situ during some period of time: this might help
to carry out additional measurements that a normal station is not able to perform
(Teodorani, 2009c). For instance, personnel on field might use portable telescopes both
12
for imaging and high-resolution spectroscopy (Stephan et al., 2009), heavy and
sophisticated gravimeters, portable radars (Montebugnoli et al., 2009) and other
professional scientific instrumentation. Personnel might also conduct tests using a
powerful Laser against a presumably anomalous light target (Strand, 1984; Teodorani &
Strand, 1998; Teodorani, 2000, 2001, 2009c), after ascertaining using a radio scanner
that the light phenomena are not airplanes.
L. Data processing and analysis. Data acquired using the measurement instruments that
equip the automatic station are intended to be remotely downloaded by all the
investigators that belong to this project. According to the competence data analysis is
expected to be carried out by the specialists in several fields and, in case, shared with
academic researchers and professors in order to profit from their technical response.
More than one investigator should process the same kind of data, using the same or
different software, while results must be compared together.
M. Hiring of Ph.D. students. It would be extremely interesting and profitable to involve
young scientists (graduate students who already own a master degree) who want to
work for their Ph.D. research in this specific field. Such students might be searched at
Universities in the faculties of observational astronomy, experimental physics and
optical and/or electronic engineering. They might be involved both in the data
acquisition and in the data processing/analysis/interpretation phase. Such students
should be supervised both by their academic professor and by the physical
scientists/engineers who work directly in the project. Young scientists are notoriously
very mentally fast and motivated, and being able to find at least one of them would be a
great resource for the project.
N. Consultancy with engineering experts. The experience acquired on the data acquisition
of UFO phenomena using automated stations (PH website) is quite new and the
technical experts (including technical personnel from the military in case) in this specific
field are still very few in the world. Such experts should be promptly consulted and, in
case, involved inside the project as external consultants. In particular, engineering
competence might be extremely important when one deals with the desired data rate
of the entire system (Masters, 2013). In fact, whatever the sophistication of the system
is a time latency problem inevitably occurs at the time in which data are acquired. This
causes a delay in communication between sensors within a given unit, and between
units in the global network. The faster the communication and less the latency, the
greater the cost. Accurate time stamp data for each unit in the network will be vital for
relating observed events to each other, in order to allow an acceptable synchronization
between all systems. A bad synchronization might prevent one to correlate two crucial
events (especially the very short time-scale ones) recorded using different instruments,
so that important information might be lost. Concerning electromagnetic sensors,
problems related to the use of a PC interface (Ailleris, 2013), constituted by a
13
microcontroller with buffers connected to each sensor and each USB bridge, could
create self-interference (or intermodulation) and contaminate the sensors masking the
results. Therefore the use of microcontrollers or bridges relying on cycles of clock should
be reduced. If still a PC interface is needed, the compact 'box' would need either a real
time remote connection via wireless network (through a cellular modem) or have its
own record board with memory circuit that would be later assessed by the PC. The
correct circuitry (where all circuits are properly connected) and microelectronics must
be used in order to solve this problem: on the contrary data might be polluted by
electronics itself. Considering these important issues of electronic engineering, which
once properly faced would inevitably increase the cost of the entire apparatus, there
are good reasons to suggest that at the same cost it is better to use less instruments but
with such problems reasonably solved than too many instruments (even if absolutely
important per se in order to face the physics of the investigated problem properly) for
which data communication and PC interface are unsatisfactory.
4. Measurement instruments: procedures
The idea consists in starting the project using only the basic unit (or: “main system”), in
order to test its functioning for a certain period of time and to verify if such a strategy is
effectively able to record the passage of possible UFOs. The main unit employs an all-sky
camera that is simultaneously able to acquire both images and optical spectra. Regarding
the possibility to take spectra (Kitchin, 2008) simultaneously with images, it is expected
that a beamsplitter directs half of the light from the main lens to the entrance slit of the
optical spectrometer, which can be of low or medium-high dispersion kind according to the
choice that will be done. When a luminous phenomenon of whatever nature appears in
the sky, there will be an increase in the intensity of the all-sky collected light. The all-sky
background without the object is subtracted to obtain the spectrum of the luminous
object. A recent aimed development and patented realization shows that a spectrograph
for UFO detection (low and medium-high resolution variants) can be of the slit-free and
direct-viewing type (Masters, 2012). At the same time in which optical measurements are
taken, a magnetometer, an electrostatic detector (or electronic electroscope) and a
weather station are expected to acquire data all the time. Obviously all of the four
instruments are time-synchronized and connected together using one or more dedicated
computers that pilot them and save the obtained data. If during a certain period of time
(typically: one or two years) the basic unit demonstrates to be productive then the
demand of new money funding would be justified in order to implement two additional
units: the optical and the electromagnetic units. The scope of such additional units is to
improve the monitoring procedure following a more analytic mode. Of course in order to
achieve this task it is necessary to carry out a lot of engineering and informatics work, in
particular in order to permit to the main unit to communicate with the additional two
14
units. One “trigger parameter” must be chosen in order to permit the main unit to activate
the other two ones. For instance, such a parameter might be given by the target’s
luminosity threshold (PH, website) or speed or by an alert coming from the magnetometer
or the electrostatic detector. Moreover the Altazimuth coordinates of the target must be
recorded continuously. In such a case the coordinates would be immediately
communicated to all the instruments of the optical system, which then would start to track
the target and acquire data of it. All the three videocameras and the radiometer are
expected to be mounted on a solid steerable tripod. A second steerable tripod would have
all the three DSLR cameras mounted over it as well. All the operations using the main
system and the optical system would be synchronous with the operations using the
electromagnetic system, which would be activated by the trigger parameter from the main
unit. Computers (certainly more than one, or a single powerful workstation) are intended
to control: a) the Altazimuth movement of optical instruments; b) all the data acquisition
operations. Data are then deposited on a memory storage disk, and can then be
downloaded from remote stations for analysis.
5. Physical parameters to be obtained
All the measurements that are acquired using all the described instruments (see Figure 2)
must permit investigators to obtain a possibly accurate evaluation of the most important
physical, geometric and kinematic parameters (Kitchin, 2008; Lang, 2005) of the luminous
flying target. According to the used instrument it is possible to obtain the following
physical parameters:
MAIN UNIT
Electrostatic Detector Number of electrostatic particles per second.
Weather Station Atmospheric parameters (air temperature, pressure, humidity, wind
speed, clouds, etc.).
Magnetometer Magnetic field intensity (x, y and z components).
All-Sky Camera Apparent target luminosity and color (using photometry). Light
surface distribution (Point Spread Function). Angular speed of the target in the sky.
Spectrochemical line identification. Intensity and equivalent width of spectral lines (if
present), from which it is possible to: a) calculate the number of atoms of a given
(identified) chemical element that are excited; b) measure the flux of the continuum
spectrum.
15
OPTICAL UNIT
Optical Radiometer Electromagnetic radiation intensity in the optical (and, in case, in
the near IR and UV too).
High-Sensitivity Videocamera Kinematic characteristics of the target (speed,
acceleration, changes of directions). Angular speed of the target in the sky. Apparent
target luminosity and color. Light surface distribution (Point Spread Function).
High-Sensitivity Videocamera + Low-Resolution Grating Spectrochemical line
identification. Intensity and equivalent width of spectral lines and their variation with
time.
DLRS Camera + Echelle Grating Spectrochemical line identification. High-precision
intensity and equivalent width of spectral lines. Morphology of spectral lines. Magnetic
field intensity from possible Zeeman Effect that is in case present in spectral lines.
Possible line blue or red-shift in case of extremely high speed of excited gases. Possible
rotational line broadening.
Optical and UV-IR DSLR Cameras Apparent target luminosity, color and light surface
distribution from high-resolution photographs, in the infrared, optical and ultraviolet
ranges.
High-Speed Videocamera Possible high-speed variation of luminosity, color and
surface shape and dimensions from optical video frames (typically: 10.000 fr/sec).
ELECTROMAGNETIC UNIT
VHF and VLF/ELF Receivers and UHF Spectrometer Intensity, variation, periodicity and
morphology of radio waves in the UHF, VHF and VLF/ELF ranges.
Geiger Counter Intensity of radioactivity emission (alpha, beta, gamma particles).
Clearly, being all the measurement instruments working all the time and all together
simultaneously, it becomes possible to: a) evaluate the time-variation of all the measured
parameters; b) search for correlations between them. From this it may be possible to infer
some important information on the physics of the problem (Teodorani, 2001).
Apart from inevitable limitations for the use of spectrographic systems and the optical
radiometer except for the case in which the target is very luminous, being the
background emission of the sky known all the other instruments that are implemented
inside the automated station may permit to furnish important information about diurnal
anomalous flying phenomena too, in particular about their kinematic and morphologic
16
characteristics in the optical and in the infrared and all the magnetic, electromagnetic and
radioactivity parameters.
Concerning photometric and geometric parameters of such kind of flying target, it is
evident that, until its distance is not known, what we can obtain are only their apparent
value. In order to obtain their intrinsic value we need to obtain the distance parameter
(Teodorani, 2001; see TECHNICAL APPENDIX). In the absence of a radar or a Laser range
finder which might be anyway implemented inside the station in a further phase
triangulation is the only way to obtain distance and consequently the intrinsic (linear)
dimensions and the absolute luminosity of an extended target (Kitchin, 2008; Lang, 2005).
In order to achieve this goal it is necessary to place a further videocamera or DSLR camera
at some distance from the main measurement station (PH website). Assuming that such an
external optical device is working simultaneously with the optical devices that are working
inside the station, it is then possible to obtain the target’s distance whose precision will
the higher, the higher the used baseline (distance of the station from the external optical
system). At this point we are in a condition to pass from the measured apparent
luminosity, angular velocity and angular dimensions of the target to intrinsic luminosity,
linear (projected) velocity and linear dimensions. Once the distance parameter is acquired
our physics action is completed. Such procedures are identical to the ones used in
astronomy (Lang, 2005).
As Dr. Mark Rodeghier rightly noted (Rodeghier, 2013), having several types of optical
instruments is ideal, but this might not be financially viable, so such devices should be
ranked in terms of optimal scientific value versus the cost and complexity. Such a
specialized optical unit in general is obviously an (extremely important per se, in physical
terms) opportunity that might be employed in the (more or less near) future only if the
data previously obtained from the main unit are in case so crucial to justify a further
money funding. According to the obtained money funding it might be possible to further
implement all the listed optical instrumentation, or only some components of it with a
possible priority given to the high-sensitivity videocamera plus its attached low-resolution
grating and to the high-speed videocamera. Further optical instruments might be added in
a subsequent phase (if the necessary money funding is sufficient), considering that anyway
a container of them should be prepared since the beginning to contain all the proposed
instruments of the optical system. It is anyway clear that, apart from the costs, when the
complexity of the system increases the global efficiency of the entire system might
decrease as well at times. Of course the best compromise between complexity, costs and
physical prominence of the data that are expected to be obtained, can be discussed
according to which priorities will be decided.
17
Figure 2. List of instrumental and strategic priorities.
18
6. Strategy and goals
The UFO phenomenon is an unidentified phenomenon per se (Hynek, 1972). Therefore
what are we searching for with this research? The answer is very simple and it can be given
in three ways, as it follows.
I We want to ascertain if the observed phenomenon can be identified with known
causes, which can be natural, optical or manmade (Condon, 1969; CUFOS website; Hendry,
1979; Hourcade, 2011; Pettigrew, 2003; Teodorani, 2009a). There is no doubt that a
rigorous procedure such as the one described previously can permit scientific investigators
to achieve this goal very accurately.
II We want to ascertain how and where anomalous natural luminous phenomena occur
(Teodorani, 2008, 2011), in order to be able to explain their physics once and for all. Much
previous research work has been already done in the course of instrumented missions to
areas such as Hessdalen in Norway and other locations in the world where a similar
phenomenon occurs (Bunnell, 2003; MLR website; PH website; PSI website; Rutledge,
1981; Stephan et al., 2009; Strand 1984; Teodorani, 2004, 2009c, 2011). This research is of
great importance as it might deal with a new form of energy able to confine plasma inside
a spherically-shaped object (Teodorani, 2011). Such ball-shaped plasma phenomena are
apparently similar to the ball lightning phenomenon, but much larger and much longer in
duration (Stenhoff, 1999) and are possibly triggered by geophysical causes such as
piezoelectricity (Derr, 1986; Teodorani, 2004, 2008), wave-particle interaction (Zou, 1995),
the P-hole mechanism (Freund, 2003), triboluminescence or a (recently proposed) “natural
battery mechanism” (Monari et al., 2013). Of course the strategy adopted with the
proposed automated station might largely help to understand something more about ball
lightning too.
III Is Earth visited by exogenous intelligences from other planets or dimensions? This
possibility is scientifically non-zero and must be accurately investigated. Of course if this
would be the case what we would observe would be simply flying machines in the sky, able
to self-sustain and to move due to their own specific propulsion mechanism (Davis, 2004;
Hill, 1995; LaViolette, 2008). Our instruments are indeed able to ascertain if what we
observe is a natural phenomenon or not. In particular the dynamic behavior of the physical
parameters that we can obtain can tell us something (or much, in case) just on the nature
of the propulsion system (Teodorani, 2000, 2001). For instance, the variability of light,
spectral lines, magnetic field intensity and speed might be a byproduct of propulsion.
Alternatively (but less probably) the produced light might be due to the illumination
system of such alleged machines. We have at our disposal a quite rich database describing
the radiometric, photometric and spectroscopic behavior of man-made illumination
systems, which could be then compared with what we effectively might observe of such
hypothetic flying machines of non-human origin (unless they adopt a sort of mimicry
19
strategy). A project called SETV (Search for Extraterrestrial Visitation) was born more than
a decade ago and is a corollary of the standard SETI Project. SETV involves both a long-
range (within the entire solar system) and a short-range variant (Ailleris, 2011; Ansbro,
2001; Deardorff et al., 2004; Gato-Rivera, 2006; Stride, 2001; Teodorani, 2006, 2013). The
second one would be exactly what our automatic station would aim to. Evidently if a true
“smoking gun” would come out from the results obtained from the measurement
instruments of such a station, this would mean the word *end* of over 60 years of
disinformation, unconvincing stories and anecdotes, hoaxes, conspiracies, pseudoscience,
new age sects. Only science, together with excellent investigators of ufology (CUFOS
website; Haines, 1980; Hourcade, 2011; Kean, 2011; Maccabee, 1994, 1999; NARCAP
website; Rodeghier, 1981; UAPSG website), can furnish a solid answer to this ultimate
question and numbers speak alone. But science might also demonstrate (or disprove, in
case) that much of the so called “UFO phenomenon” might be just a huge piloted hoax
that is a part of a colossal experiment of psychological warfare (Teodorani, 2009a).
7. Conclusive remarks
Whatever the UFO phenomenon may be a serious investigation urges, especially during an
epoch in which the gradual collapse of authentic human and intellectual values together
with the fear for the future drives people to escape from reality: whatever apparently
strange flies in the sky can become automatically a sign of visitation from outer space.
Internet is literally full of hoaxes and badly interpreted prosaic phenomena. Such a childish
and ill aptitude, together with delusional sickness, indirectly discredits the determined
efforts of serious scholars scientists and ufologists who are devoted to this study most of
the time at their own expense that are directed to investigate an anomalous
phenomenon that, in spite of misunderstanding and disinformation, truly exists. In fact
several decades of testimonial and instrumental researches show that an anomalous signal
can be effectively extracted from the noise. The unpredictability and random nature of the
UFO phenomenon shows without any shadow of doubt that the only way to acquire
scientific data of it consists of using measurement stations that, being placed at locations
that are considered statistically “hot”, work automatically. This permits investigators to
analyze the obtained data using a methodology that is fully scientific and that would be if
properly realized extremely similar to the one used in astronomy and astrophysics. This
paper must be just intended as a platform of discussion in order to attempt to trigger a
rational dialectics about a concrete realization of such a project. Several manifestations
presented by the true UFO phenomenon, once witnesses are accurately screened and first
measurements are taken, show something that seems to defy sometimes the known laws
of ordinary physics. This should be enough as a stimulus for the physical scientists of the
entire world. Whatever the nature of the observed phenomenon is, it might open some
doors to new laws of physics that might largely expand our scientific knowledge and
20
understanding of the facts of the Universe, and maybe mean a significant evolution for
Mankind.
TECHNICAL APPENDIX How physical parameters are deduced
The luminosity that we can measure of a nocturnal light represents only the “apparent luminosity”,
as the electromagnetic radiation that is received (at whatever wavelength) decreases with the
inverse square of distance. If we really want to make true physics on the acquired data it is
necessary to obtain the “absolute luminosity”, from which it is possible to obtain the energy density
of the monitored luminous phenomenon. In this regard it is very important to show how to proceed
in practice.
Let’s imagine that one is able to obtain videos, photographs or CCD images of a strange light
phenomenon, and that we are able to assess in some way the fundamental factor given by
"distance". Then we are in a condition to obtain the absolute luminosity using the following formula
(Maccabee, 1999):
Vd9.3
2
APP
2
ABS e
TD
4
L
d4L
Where d is the distance (in m) of the luminous phenomenon, LAPP = I A (in lmsec) is the total
energy received by the CCD chip of the camera integrated over the image area (namely, LAPP
represents the value of the apparent luminosity), I is the energy per unit area of the image (in lmsec
m-2), A is the image area (in m2), V is the optical visibility distance (in m), is the duration of the
light phenomenon (in sec), D = F / f (the ratio, in m2) gives the aperture diameter of the lens, where
F and f are respectively the focal length and the f-number of the camera, T is the lens transmission
factor.
At this point we have all the elements that allow us to obtain the important value of the absolute
luminosity LABS, namely the intrinsic luminosity of the light phenomenon when the value of
distance is zero. From this value we are then able to obtain the quantity of energy that is produced
by the phenomenon at any given instant. Realistically what we obtain is the absolute luminosity that
is produced by the phenomenon during a time interval t, which corresponds to the integration time
t that is used by the optical instruments in order to expose correctly the light on the used photon-
recording sensor. Clearly only the high-speed videocamera can narrow t down to 1/10.000 sec
(typically). On the contrary, the value of t is typically a factor 102-103 higher for normal
videocameras and a factor 105-107 higher for DSLR cameras (which require a given exposure time
in order to collect enough photons on the CCD chip). Of course we have also to consider that the
absolute luminosity that we obtain is not the total luminosity of the light phenomenon, but rather the
absolute luminosity that can be obtained only on a limited frequency range given by , where is
the frequency, according to the bandwidth that is used, which in our case is constituted by the near
infrared, optical and near ultraviolet ranges.
In any fact: a) if we assume that the nature of the emitted light is due to a thermal process that is
typical of a blackbody radiation and which causes a ionization/excitation condition around or within
( 1 )
21
the light phenomenon; b) if we assume that (for simplicity of calculation) the light phenomenon is
spherically shaped and that it emits light as an isotropic radiator; c) if we assume that the emitted
radiation at frequencies that are beyond the near infrared and near ultraviolet bandwidths is
negligible, then we can obtain an important relation between the absolute luminosity, the intrinsic
radius R of the object and its temperature T. This relation is given by a reasonable approximation of
the Stefan-Boltzmann equation (Lang, 2005) given by:
4
2
ABS TR4L
considering that:
2d
R
where is the Stefan-Boltzmann constant, T is the temperature of the object, is the angular
diameter of the object and d is the distance of the object from the observer.
It is obvious that this way we are in a condition to obtain easily the intrinsic diameter D = 2R of the
object, once the angular diameter and the distance d (via triangulation, radar, Laser telemetry and
other methods) are known. At this point if we insert the value of R inside formula (2) for absolute
luminosity (whose value is obtained by formula (1)) then we are able to obtain the approximate
value of the temperature T of the object (the same value can be cross-confronted with the value of T
that is obtained from spectroscopy after analyzing spectral lines). More precisely what we obtain is
the “color temperature” of the object, but if we assume that the value of T at the very high energy
(above the ultraviolet) and at the very low energy (below the infrared) frequency windows are
negligible, there would be good reasons to argue that the color temperature approximates very well
the total or “effective” temperature.
It is clear that if we have the “factor distance” at our disposal we are also in a condition to calculate
the absolute flux of the electromagnetic radiation emitted in the radio range and the absolute
magnetic field intensity too.
This was just an example furnished in order to show how the determination of the distance
parameter is absolutely necessary if we want to obtain three fundamental parameters of the object
directly from observations: the absolute luminosity, the effective temperature and the real
dimensions of the object. With these data in hands, we are in a condition to understand the physical
nature of the anomalous phenomenon, from which it is maybe possible to understand something of
the propulsion mechanism if the observed luminous phenomenon is really a flying machine.
It is more than obvious that such “static data” namely referred to a precise instant in which the
phenomenon is measured will acquire a maximized importance when we study how the obtained
parameters vary with time. In fact all the instruments are intended to acquire data all the time. For
instance, we might obtain a pulsation period P (if a regular pulsation is effectively recorded) and
possibly a (both increasing a decreasing) variation of it: this might be a very important
measurement, and, especially if it is correlated with color and speed variation of the object, it might
furnish to us some possible crucial information on a possible object’s propulsion, which would be
( 2 )
22
deduced dynamically. Of course such an information will be even more maximized if at the same
time we are able to measure the variation of: a) the intensity of spectral lines; b) the change of
morphology of spectral lines; c) the magnetic field intensity; d) the intensity of the electromagnetic
emission in the UHF, VHF and VLF/ELF radio frequency intervals, e) the number of electrostatic
and radioactive particles. In any fact, in the absence of the important factor given by the object’s
distance, there is no doubt that we might obtain a satisfactory physics as well limiting ourselves to
study the time-variation of the apparent observed parameters.
References
1. Akers, D. (2006). The Willard J. Vogel Study :
http://www.ltpaobserverproject.com/uploads/3/0/2/0/3020041/the_willard_j._vogel_study.pdf
2. Ailleris, P. (2011). “The lure of local SETI: fifty years of field experiments”. Acta Astronautica. Volume
68, Issues 12, pp. 215.
3. Ailleris, P. (2013). Personal extensive communications through an ESTEC engineering expert. August 21,
2013.
4. Ansbro, E. (2001). New OSETI observatory to search for interstellar probes”. In: S. A. Kingsley and R.
Bhathal (eds.) The Search for Extraterrestrial Intelligence (SETI) in the Optical Spectrum III. Proc. SPIE,
Vol. 4273, pp. 246-253. USA.
5. Ansbro, E. (2004). “A new wide-field spectrograph”. In: Proc. SPIE 5492, Ground-based
Instrumentation for Astronomy, 1290 (September 30, 2004).
6. Bunnell, J. (2003). Night Orbs. Ed. Lacey Publishing Company, USA.
7. Condon, E. U. (1969). Scientific Study of Unidentified Flying Objects, University of Colorado, Bantam
Books, New York (USA), Toronto (Canada), London (GB). Online at: http://www.avia-
it.com/act/biblioteca/libri/PDF_Libri_By_Archive.org/AVIATION/Final%20report%20of%20the%20Scien
tific%20study%20of%20Unidentified%20Flying%20Objects%20-%20Condon%20E..pdf
8. Cornet, B. (1998). “The Performance” : http://www.abcfield.force9.co.uk/bcornet/
9. Davis, E. W. (2004). “Teleportation Physics Study”. Special Report, N. AFRL-PR-ED-TR-2003-0034. Air
Force Research Laboratory, Air Force Meteriel Command, Edwards Air Force Base CA 93524-7048 :
http://www.fas.org/sgp/eprint/teleport.pdf
10. Derr, J. S. (1986). “Luminous phenomena and their relationship to rock fracture”. Nature, 321, pp. 470-
471.
11. Deardorff, J.; Haish, B.; Maccabee, B. & Puthoff, H. E. (2005). “Inflation theory implications for
Extraterrestrial Visitation”. JBIS, Vol. 58, pp. 43-50. Online: http://www.ufoskeptic.org/JBIS.pdf
12. Freund, F. T. (2003) “Rocks that Crackle and Sparkle and Glow: Strange Pre-Earthquake Phenomena”.
Journal of Scientific Exploration, 17, no. 1, pp. 37-71 :
http://www.scientificexploration.org/jse/articles/pdf/17.1_freund.pdf
13. Fryberger D. (1997). “A Model for Ball Lightning”. ØIH Rapport, 1997(5), Høgskolen i Østfold (Norway),
pp. 182.
14. Gato-Rivera, B. (2006). “Brane Worlds, the Subanthropic Principle and the Undetectability Conjecture”.
ArXiv: http://arxiv.org/pdf/physics/0308078v4.pdf
23
15. Gröschel, G. (website).”UFO Überwachungssystem Übersicht”. Institut für Technische UFO-Forschung
Digital Service : http://www.biz11.de/images/Dateien/d-UFO-%C3%9Cberwachungssystem.pdf
16. Haines, R. (1980). Observing UFOs An Investigative Handbook. Burnham Inc Pub.
17. Hill, P. R. (1995). Unconventional Flying Objects: A Scientific Analysis. Hampton Roads Publishing.
18. Hourcade, M. (2011). In Search for Real UFOs. AuthorHouse Publishing. Online at:
http://www.scribd.com/doc/64140571/In-Search-of-Real-UFOs
19. Hendry, A. (1979). The UFO Handbook. Doubleday.
20. Hynek J. A. (1972). The UFO Experience: A Scientific Inquiry. H. Regnery Co.
21. Kean, L. (2011). UFOs: Generals, Pilots, and Government Officials Go on the Record. Three Rivers Press.
22. Kelleher, K. & Knapp, G. (2005) Hunt for the Skinwalker. Ed Paraview Pocket Books.
23. Kitchin, C. R. (2008). Astrophysical Techniques. CRC Press.
24. International Earthlight Alliance (IEA): http://www.earthlights.org/
25. Italian Committee for Project Hessdalen (ICPH): http://www.itacomm.net/PH/CIPH/HOME_PAGE.html
26. Lang, K. R. (2005). Astrophysical Formulae. Springer.
27. LaViolette, P. A. (2008). Secrets of Antigravity Propulsion. Bear & Co.
28. Maccabee, B. (1994). Strong Magnetic Field Detected Following a Sighting of and Unidentified Flying
Object”. Journal of Scientific Exploration, 8, p. 347.
29. Maccabee, B. (1999). Optical power output of an unidentified high altitude light source”. Journal of
Scientific Exploration, 13, pp. 199-211.
30. Marfa Lights Research (MLR) : http://www.nightorbs.net/
31. Masters, R. A. (2012). “High-Resolution Slit-Free Direct-Viewing Multiplexing Field Spectrograph”.
United States Patent Application Publication. Pub. No. US 2012/0287430 A1 . Online at:
http://www.freepatentsonline.com/20120287430.pdf
32. Masters, R. A. (2013). Personal extensive communications. August 20, 2013 August 24, 2013
September 10, 2013.
33. Meessen, A. (2012). “Evidence of Very Strong Low Frequency Magnetic Fields”. PIERS Proceedings,
Moscow, Russia, August 19{23, 2012 : http://www.cobeps.org/pdf/meessen_evidence.pdf
34. Monari, J.; Montebugnoli, S. & Serra, R. (2013). “Hessdalen – a perfect “natural battery””. ICPH
Articles: http://www.itacomm.net/PH/2013_Monari_et-al-en.pdf
35. Montebugnoli, S.; Monari, J.; Cattani, A.; Maccaferri, A.; Poloni, M.; Bortolotti, C.; Roma, M.; Hauge, B.
G.; Strand, E. P. & Cevolani, G. (2002). Measurements with a low power pulsed radar in the Hessdalen
2002 camp”. ICPH Articles : http://www.itacomm.net/ph/radar/radar_e.pdf
36. National Aviation Reporting Center on Anomalous Phenomena (NARCAP) : http://www.narcap.org/
37. Pettigrew, J. D. (2003) “The Min Min light and the Fata Morgana - An optical account of a mysterious
Australian phenomenon”. Clinical and Experimental Optometry, 86: 2: 109120 :
http://www.uq.edu.au/nuq/jack/MinMinCEO.pdf
38. Project Hessdalen (PH) : http://www.hessdalen.org/
39. Project Starlight International (PSI) : http://www.nicap.org/madar/psi.htm
24
40. Rodeghier, M. (1981). UFO Reports Involving Vehicle Interference: A Catalogue and Data Analysis.
Center for UFO Studies.
41. Rodeghier, M. (2013). Personal extensive communications in 8 points. September 9, 2013.
42. Rutledge, H. (1981). Project Identification: The first Scientific Study of UFO Phenomena. Prentice-Hall.
43. SOSO LIVE CAMERA (Massimo Silvestri et al.) : http://www.ciph-SOSO Live Camera.net/SOSO LIVE
CAMERA/SOSO LIVE CAMERA_LIVE_CAMERA.html
44. Stephan, K. D.; Ghimire, S.; Stapleton,W. A.; & Bunnell J. (2009). “Spectroscopy applied to observations
of terrestrial light sources of uncertain origin”. American Journal of Physics, 77(8), pp. 697-703 :
http://uweb.txstate.edu/~ks22/pdfs/MLPaper_AJP.pdf
45. Stenhoff, (1999). Ball lightning. An unsolved problem in atmospheric physics. New York: Kluwer
Academic/Plenum.
46. Strand, E. P. (1984). “Project Hessdalen 1984 – Final Technical Report”. Project Hessdalen Articles and
Reports : http://www.hessdalen.org/reports/hpreport84.shtml
47. Stride, S. L. (2001). “An instrument-based method to search for interstellar robotic probes”. J. Brit.
Interplanetary Soc., n. 52, pp. 2-13. Online: http://www.sunstar-solutions.com/sunstar/SETV/JBIS-
SETV01.pdf
48. Sturrock P. (1999) The UFO Enigma: a New Review of the Physical Evidence. New York: Warner Books.
49. Teodorani, M. & Strand, E.P. (1998). “Experimental methods for studying the Hessdalen phenomenon
in the light of the proposed theories: a comparative overview”. ØIH Rapport, n. 1998:5, Høgskolen i
Østfold (Norway), pp. 1-93. Online: http://www.scribd.com/doc/126582698/Experimental-Methods-
for-studying-the-Hessdalen-Phenomenon-in-the-light-of-the-Proposed-Theories-a-Comparative-
Overview
50. Teodorani, M. (2000). “Physical data acquisition and analysis of possible flying extraterrestrial probes
by using opto-electronic devices”. Extraterrestrial Physics Review, Vol. 1, No. 3, pp. 32-37. Online:
http://www.scribd.com/doc/126580079/Physical-Data-Acquisition-and-Analysis-of-Possible-Flying-
Extraterrestrial-Probes-by-Using-Opto-Electronic-Devices
51. Teodorani, M. (2001). “Physics from UFO Data”. ICPH Articles, N. 2 :
http://www.itacomm.net/ph/phdata_e.pdf
52. Teodorani, M. (2004). “A Long-Term Scientific Survey of the Hessdalen Phenomenon”. Journal of
Scientific Exploration. Vol. 18, n. 2, pp. 217-251 :
http://www.scientificexploration.org/journal/jse_18_2_teodorani.pdf
53. Teodorani, M. (2006). ”An Alternative Method for the Scientific Search for Extraterrestrial Intelligent
Life: “The Local SETI” “. In: J. Seckbach (ed.) Book: Life as We Know It, Springer, COLE Books, Vol. 10, pp.
487-503. Online: http://openseti.org/Docs/NewSETI_MT_LAKI.pdf
54. Teodorani, M. (2008). Sfere di Luce. Macro Edizioni.
55. Teodorani, M. (2009a). "Need to Know" vs. "Need to Believe" in UFOlogy. Xpose UFO Truth :
http://fierycelt.tripod.com/xposeufotruth/needknow_vs_needbelieve.html
56. Teodorani, M. (2009b). “A Comparative Analytical and Observational Study of North American
Databases on Unidentified Aerial Phenomena”. NARCAP Technical Reports:
http://narcap.org/reports/ONNYCT_Paper_MT_2009_REVISED.pdf
25
57. Teodorani, M. (2009c). “Scientific Inquiry on Anomalous Atmospheric Light Phenomena: Past Research
Gaps and New Methodological Goals”. ICPH Articles :
http://www.itacomm.net/PH/2009_Teodorani.pdf
58. Teodorani, M. (2011). “A Scientific Approach to the Investigation on Anomalous Atmospheric Light
Phenomena”. Workshop Fenomeni Luminosi in Atmosfera e precursori sismici: una nuova frontiera per
la scienza? Fornovo Taro (PR), 21 April 2010. GEOLAB Publication (Conference Proceedings). CNR
SOLAR, n. 3641 : http://eprints.bice.rm.cnr.it/3641/1/Fornovo_MT_2010.pdf
59. Teodorani, M. (2013). Intelligenze Oltre la Terra una visione scientifica e filosofica. Giochidimagia
Editore. Ebook: http://www.macrolibrarsi.it/ebooks/ebook-intelligenze-oltre-la-terra.php
60. The J. Allen Hynek Center for UFO Studies (CUFOS): http://www.cufos.org/
61. The Canadian UFO Survey : http://www.canadianuforeport.com/survey/index.html
62. Unidentified Aerospace Phenomena Reporting Scheme (UAPRS) : http://www.uapreporting.org/
63. University of Western Ontario (UWO) Meteor Physics Group. All-Sky Camera Network:
http://meteor.uwo.ca/
64. Unusual Aerial Phenomena Study Group (U.A.P.S.G.): http://www.uapsg.com/
65. Williams, W. SETV (Search for Extraterrestrial Visitation) : http://www.setv.org/
66. Wendt, A. & Duvall, R. (2008). “Sovereignty and the UFO”. Political Theory. Vol. 36, n. 4, pp. 607-633.
Online: http://ptx.sagepub.com/content/36/4/607.abstract
67. Zeitlin, G. Open SETI : http://openseti.org/Opening.shtml
68. Zlotnicki, J.; Yvetot, P. & Fauquet, F. (2012). “Existence of electric/magnetic signals related to unknown
luminous lights observed in Hessdalen valley (Norway)?“ Geophysical Research Abstracts, Vol. 14,
EGU2012-5967-1, 2012
69. Zou You-Suo (1995). “Some Physical Considerations for Unusual Atmospheric Lights Observed in
Norway”, Physica Scripta, 52, pp. 726-730.
Acknowledgments. This author wants to thank Professor Alexander Wendt (Ohio State University),
main chief and coordinator of the UFOAC Project, for inviting me inside this enterprise, and Dr.
Mark Rodeghier, Dr. Ron Masters and Philippe Ailleris for very sound feedbacks on this paper.
BRIEF BIOGRAPHY Dr. Massimo Teodorani is an Italian astrophysicist. He obtained his degree in Astronomy and his
Ph.D. in Stellar Physics at the University of Bologna. As a researcher at the Astronomical Observatories of Bologna and
Naples, and later at the INAF Radiotelescope of Medicina (BO), he has been involved in research on many types of
explosive stellar phenomena such as supernovae, novae, eruptive protostars and high-mass close binary stars and,
more recently, in the search for extrasolar planets and extraterrestrial intelligence within the SETI Project. He
subsequently taught quantum physics as a lecturer at the University of Bologna. Among his research interests there is
also an active involvement in the physics study of anomalous aerial phenomena. He is an expert in military
aeronautics. In addition to many technical papers in all of the mentioned subjects, he has published 17 books and
several informative articles on quantum physics, atomic and nuclear physics, astronomy, astrophysics, bioastronomy,
physics of anomalous atmospheric phenomena and aerospace subjects. He had many interviews on the media about
some of his researches, and he gave many public presentations. During his free time is also a composer of electronic
music under the pseudonym "Totemtag".
26
First UFOAC Workshop
Ohio State University
Columbus (Ohio, USA), November 1, 2013.
... Additionally, in 2015, Dr Massimo Teodorani contributed to the UFODATA project by producing a document that outlines the physical parameters that can be derived using readily available measurement instruments. This resource aims to facilitate the determination of the nature of Unidentified Flying Objects (UFOs) and the extraction of relevant physics-related data (Teodorani 2015). Lastly, a recent significant development comes from the Project Galileo, which has published in 2023 crucial peer-reviewed papers (The Galileo Project, website). ...
Article
Full-text available
The study of Unidentified Aerospace Phenomena (UAP) requires a shift from a historical, narrative-based approach to a scientific and technology-based study. To conduct unbiased and agnostic research on UAPs, rigorous scientific study is necessary, including the collection of hard data to support credible explanations or scientifically prove the existence of unknown phenomena. Obtaining reliable and valid data requires instrumented observations, including multi-wavelength and multi-mode sensors (e.g., optical, radar, infrared). We present herein an overview of the benefits as well as the strategic and tactical considerations of instrumented field studies, highlighting common limitations and shortcomings with the objective of contributing to the development of future projects. We provide an overview of some past and current UAP military and civilian projects and analyze a timetable of instrumented projects spanning the years 1950-2023, encompassing contributions from both citizen science and professional/academic science. In conclusion, this paper reflects on how UAP field experiments might look going forward. Newer technologies like digital cameras, scientific instruments, computing, big data analytics, artificial intelligence, and satellite imagery are becoming more advanced and cost-effective. This is leading to the growth and progress of technical field studies, complementing local projects with global-scale investigations. Researchers can enhance their chances of success by adopting a more disciplined approach and exploring innovative avenues. Collaboration, transparency, and standardization in data collection and analysis are crucial, while also acknowledging the complex nature of the UAP phenomenon.
Patent
Full-text available
A compact field spectrograph is described that provides a resolution of 500 or more with no entrance aperture, providing for substantial gain in light throughput, ideal for viewing multiple distant objects with or without telescopic aid, and providing the ability to observe and distinguish a multiplex of objects simultaneously, even if in motion, with minimal or no mechanical tracking required. Spectra may be viewed directly with the unaided eye, or photographed with common consumer cameras.
Conference Paper
Full-text available
Anomalous atmospheric light phenomena tend to occur recurrently in several places of our planet. Statistical studies show that a phenomenon's real recurrence area can be identified only after pondering reported cases on the population number and on the diffusion of communication media. The main scientific results that have been obtained so far after explorative instrumented missions have been carried out are presented, including the empirical models that have been set up in order to describe the observed reality. Subsequently, a focused theorization is discussed in order to attack the physical problem concerning the structure and the dynamics of " light balls " and the enigma related to the central force that maintains them in spherical shape. Finally, several important issues are discussed regarding methodology, strategy, tactics and interdisciplinary approaches.
Conference Paper
Full-text available
Measurements with a low power pulsed radar in the Hessdalen 2002 camp. Part of this paper directly derives from the Istituto di Radioastronomia Internal Technical Report N. 321 / 02, written by the same authors. The measurements performed in Norway with the radar has been made possible also with a grant from the CIPH.
Article
Full-text available
How authentic is UFO documentation? A lot of factors demonstrate -- doing a simple analysis -- that most of UFO photographic material, in particular the one that circulates on the web, is totally unreliable. It is not only a matter of lack of scientific method; it is mostly a simple matter of lack of common sense. The common sense of people is constantly made a fun of and the reasons of this are many, the most important of which is the emotional effect caused by the imaginary collective. UFO iconography is a drug at all effects, and can be used to switch minds in many ways, also to collect proselytes to make up new fanatic religions, but more generally to give people a sort of psychological medicine with which people can escape from the hard reality of everyday, where the continuous competitions of present society often obscure the human and spiritual dimension: people need to retrieve the very nucleus of their soul. This intimate need is clearly legitimate, but it is also risky: in fact persons who are not well rationally grounded are very easily subject to manipulation: it seems that most persons in the world are just in this condition, especially at our epoch. When critical thinking starts to lack, who leads this society has at his disposal a huge mass of sheep, ready to follow alleged miracles, saviour aliens and related gurus. The less people think in a grounded way the least this people are conscious of what is happening at their shoulders. This is the effect of UFO iconography. http://fierycelt.tripod.com/xposeufotruth/needknow_vs_needbelieve.html
Article
A Royal Canadian Air Force pilot while flying at an altitude of about 11 km saw and photographed a very bright, disc-like object that was remaining stationary near a thunderhead. An analysis of the photograph suggests that it would have been radiating in excess of a gigawatt of power within the spectral range of the film.
Article
We have shown why the propulsion of Unconventional Flying Objects of unknown origin can result from very intense low-frequency magnetic fields and an adequately pulsed ion-ization of the ambient medium. We also found how these fields could be produced, if the surface of these objects were superconducting. Now, we present evidence of the existence of these fields. It results from traces left on the ground by induced currents, rotating compass needles, direct magnetometer recordings and very remarkable magneto-optical effects. They provide even proof of the required pulsed ionization.
Article
Hessdalen valley, in Norway, is a north-south elongated basin of about 20 km by 10 km (latitude: 62°50'N, longitude: 11°12'E) in which few inhabitants are permanently living. Since several decades, scarce observations made mainly during night time have point out transient luminous lights, called Hessdalen phenomena ('HP'). Østfold University College was the first pioneer research centre which started to install visual and geophysical monitoring systems able to track the unknown lights (http://www.hessdalen.org/). The characteristics of the HP can be summarized as followed. They can appear in the low atmosphere, remain quite fixed and suddenly move up at a speed of several hundreds of km/s, for disappearing on the ground or in one the numerous lakes located in the area. The duration can be of a very seconds to a tens of minutes or more. The HP can be white, blue-white flashing lights, yellows or white lights and have different shapes with sizes up to some cubic metres. From 80 observations per month in the 1980's, the number has sharply decreased to about 20 per year nowadays. In 2010, French Research Centres started cooperation with Østfold University College and the Istituto di Radio Astronomia of Bologna (http://www.ira.inaf.it/). The objectives are to study radio emission in the frequency band 1 kHz to 5 MHz (see Farges et al., EGU 2012) and the possible disturbances of the electromagnetic (EM) field recorded at two remote stations located in the valley. The two EM stations are located a tens of kilometres apart along the valley axis. In the northern FIN station, a fluxgate magnetometer (resolution of 1/100 nT), two orthogonal induction coils (frequency band: 7 Hz - 8 kHz, resolution 1/100,000 nT), and two horizontal electric lines (few mV resolution) record the magnetic and electric fields, respectively. In addition, a vertical seismometer is linked to the multi-parameter FIN station. At the south OYU station, two induction coils and horizontal electric lines are set. All data are recorded at 40 Hz. We present the morphology of the EM field in the area which can define the background noise and the morphological evolution of the EM field along the axis of the valley. Some of the EM variations appear to be phase-delay of several minutes between the two stations which lead to suspect important distortions brought by superficial geological structures (mineral deposits?), some electrical current channelling and the local tectonics. During the last 2010-2011 winter campaign, only few observations by eyes were reported. During these periods, no large magnetic or electric signal was clearly identified.
Article
Technological advancements have allowed us to build robotic space probes to remotely explore the solar system. Interstellar robotic missions are under serious consideration. Advanced extant extraterrestrial civiliza- tions within the galaxy, if they exist, are very likely exploring with robotic probes as well, some of which may have reached our solar system and taken an interest in life on Earth. Recent technological advances make it possible to conduct a scientific search for evidence of extraterrestrial interstellar robotic probes. Modern solid-state sensing devices and scientific instruments, combined with high-speed computer hardware, can be used in an effort to detect the physical presence of a probe. The SETV (Search for Extraterrestrial Visitation) model is new and an offspring of SETA (artifacts) and SETI. SETV includes the construction of passive autonomous data acquisition platforms using “commercial off-the-shelf” hardware, to collect reliable and unambiguous data on anomalous observational phenomena that may be ETI probes. The SETV hypothesis and experimental methods will be described. The SETV hypothesis can be experimentally tested and attempts to statistically reject a null hypothesis which states that ETI probes do not exist. SETV Pre and Post-detection protocols are necessary and will be examined. SETV is a timely, results-oriented, method worthy of serious consideration in our continuing desire to answer the question “Are we alone?”.