Article

Improving thin-film crystalline silicon solar cell efficiencies with photonic crystals

Optics Express (Impact Factor: 3.49). 01/2008; 15(25):16986-7000. DOI: 10.1364/OE.15.016986
Source: PubMed

ABSTRACT

Most photovoltaic (solar) cells are made from crystalline silicon (c-Si), which has an indirect band gap. This gives rise to weak absorption of one-third of usable solar photons. Therefore, improved light trapping schemes are needed, particularly for c-Si thin film solar cells. Here, a photonic crystal-based light-trapping approach is analyzed and compared to previous approaches. For a solar cell made of a 2 mum thin film of c-Si and a 6 bilayer distributed Bragg reflector (DBR) in the back, power generation can be enhanced by a relative amount of 24.0% by adding a 1D grating, 26.3% by replacing the DBR with a six-period triangular photonic crystal made of air holes in silicon, 31.3% by a DBR plus 2D grating, and 26.5% by replacing it with an eight-period inverse opal photonic crystal.

Full-text preview

Available from: opticsinfobase.org
    • "Typical textured TCOs are the naturally textured ZnO:B grown by Low Pressure Chemical Vapour Deposition (LPCVD) [2], SnO 2 :F grown by Atmospheric Pressure Chemical Vapour Deposition (APCVD) [3], or sputtered and HCl-etched ZnO:Al (AZO) [5]. Besides these " traditional " light trapping schemes, other nanoscale approaches are currently under investigation including photonic crystals [11], nanowires [12], and periodic or periodic-disordered nanostructures [13]. "
    [Show abstract] [Hide abstract]
    ABSTRACT: Aluminium induced texturing (AIT) method has been used to texture glass substrates to enhance photon absorption in microcrystalline thin film Si solar cells. In this process, a thin Al film is deposited on a glass substrate and a non-uniform redox reaction between the glass and the Al film occurs when they are annealed at high temperature. After etching the reaction products, the resultant glass surface presents a uniform and rough morphology. In this work, three different textures (σrms~85, ~95, ~125 nm) have been achieved by tuning the dc sputtering power and over them and over smooth glass, pin microcrystalline silicon solar cells have been fabricated. The cells deposited over the textured substrates showed an efficiency improvement in comparison to the cells deposited over the smooth glass. The best result was given for the glass texture σrms~125 nm that led to an average efficiency 2.1% higher than that given by the cell deposited on smooth glass.
    No preview · Article · Apr 2016 · Solar Energy Materials and Solar Cells
  • Source
    • "Although, silicon is abundantly available in nature, it is extracted from silica (silicon dioxide SiO 2 ) which makes it expensive to get it in its pure form. The current technology of a thin film based PV cell tends to reduce the amount of silicon requirement per unit cell and hence there is a reduction in the cost of manufacturing these devices [4] [5]. Nevertheless, although thin film solar cell technology reduces the amount of material requirement per unit cell (subsequently the total cost), this process has a disadvantage of reducing absorption properties of the structure. "
    [Show abstract] [Hide abstract]
    ABSTRACT: The efficiency of solar photovoltaic (PV) cells has been one of the major problems impeding its global adoption as one of the sustainable substitutes to fossil fuel based technologies. Metamaterial (MTM) based solar cells offer an opportunity towards increasing the system efficiency by enhancing the total absorbed solar radiation incident on this device. In this study, a nanostructure-based MTM perfect absorber has been designed and simulated. By adjusting geometrical parameters and MTM structure properties, nearly perfect dual-band absorptions have been obtained with 99.99% and 99.90% absorption at 543.75 THz and 663.75 THz, respectively. The proposed structure is simple and more flexible for scaling, which helps achievement of multiple-band absorption. Implementation of the intended MTM structure can effectively lead to the realization of more efficient PV solar cells.
    Full-text · Article · Oct 2015 · Vacuum
  • Source
    • "Although, silicon is abundantly available in nature, it is extracted from silica (silicon dioxide SiO 2 ) which makes it expensive to get it in its pure form. The current technology of a thin film based PV cell tends to reduce the amount of silicon requirement per unit cell and hence there is a reduction in the cost of manufacturing these devices [4] [5]. Nevertheless, although thin film solar cell technology reduces the amount of material requirement per unit cell (subsequently the total cost), this process has a disadvantage of reducing absorption properties of the structure. "

    Full-text · Dataset · Aug 2015
Show more