Content uploaded by Ali S. Faris
Author content
All content in this area was uploaded by Ali S. Faris on Feb 28, 2014
Content may be subject to copyright.
Available via license: CC BY-NC-ND 3.0
Content may be subject to copyright.
Energy Procedia 18 ( 2012 ) 327 – 338
1876-6102 © 2012 Published by Elsevier Ltd. Selection and/or peer review under responsibility of The TerraGreen Society.
doi: 10.1016/j.egypro.2012.05.044
Effects of Magnetic Field on Fuel Consumption and Exhaust
Emissions in Two-Stroke Engine
Ali S. Farisa, Saadi K. Al-Naserib, Nather Jamal, Raed Isse, Mezher Abed, Zainab
Fouad, Akeel Kazim, Nihad Reheem, Ali Chaloob, Hazim Mohammad, Hayder Jasim,
Jaafar Sadeq, Ali Salim, Aws Abas
a Department of Physics, College of Education, Aliraqia University, Baghdad, Iraq
bEnvironmental & Water Research & Technology directorate, ministry of science and technology, Baghdad, Iraq
Abstract
The energy of permanent magnets was used in this research for the treatment of vehicle fuel (Iraqi gasoline), to
reducing consumption, as well as reducing the emission of certain pollutants rates. The experiments in current
research comprise the using of permanent magnets with different intensity (2000, 4000, 6000, 9000) Gauss, which
installed on the fuel line of the two-stroke engine, and study its impact on gasoline consumption, as well as exhaust
gases. For the purpose of comparing the results necessitated the search for experiments without the use of magnets.
The overall performance and exhaust emission tests showed a good result, where the rate of reduction in gasoline
consumption ranges between ( -1 ) %, and the higher the value of a reduction in the rate of 1 % was obtained using
field intensity 6000 Gauss as well as the intensity 9000 Gauss. It was found that the percentages of exhaust gas
components (CO, HC) were decreased by 30%, 40% respectively, but CO2 percentage increased up to 10%.
Absorption Spectrum of infrared and ultraviolet radiation showed a change in physical and chemical properties in
the structure of gasoline molecules under the influence of the magnetic field. Surface tension of gasoline exposed to
different intensities of magnetic field was measured and compared with these without magnetization.
© 2010 Published by Elsevier Ltd. Selection and/or peer-review under responsibility of [name organizer]
Keywords: magnetic treatment, fuel consumption, exhausts emission, IR and UV spectra, surface tension.
* Corresponding author. Tel.: +9647801673748; fax: +0-000-000-0000 .
E-mail address: shynier2004@yahoo.com.
Available online at www.sciencedirect.com
© 2012 Published by Elsevier Ltd. Selection and/or peer review under responsibility of The TerraGreen Society.
328 Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338
1. Introduction
sit of carbon residue that clogs carburetor, fuel injector,
leading to reduced efficiency and wasted fuel. Pinging, stalling, loss of horsepower and greatly decreased
mileage on cars are very noticeable. Most fuels for internal combustion engine are liquid, fuels do not
combust until they are vaporized and mixed with air. Most emission motor vehicle consists of unburned
hydrocarbons, carbon monoxide and oxides of nitrogen. Unburned hydrocarbon and oxides of nitrogen
react in the atmosphere and create smog. Generally a fuel for internal combustion engine is compound of
molecules. Each molecule consists of a number of atoms made up of number of nucleus and electrons,
which orbit their nucleus. Magnetic movements already exist in their molecules and they therefore
already have positive and negative electrical charges. However these molecules have not been realigned,
the fuel is not actively interlocked with oxygen during combustion, the fuel molecule or hydrocarbon
chains must be ionized and realigned. The ionization and realignment is achieved through the application
of magnetic field [1, 2].
Many of experimental studies which present evidences of the benefits of magnetic treatment were
occurred. For motor vehicles and industrial boilers, much fuel economy and noticeable soot suppressions
could be approached when the magnetic treatment was introduced [3]. For pollution due to automobile
emissions, it is of great concern more, particularly in metropolitan cities. It creates a potential threat to the
existence of healthy life [4-5], the enhancement of oil recovery and prevention of wax deposition [6]. In
petroleum production, transportation and refining; the improvement of fluidity of crude oils [7].
Magnetic fuel treatment works on the principle of magnetic field interaction with hydrocarbon
molecules of fuel and oxygen molecules. Liquid fuel is a mixture of organic chemical compounds
consisted predominantly of carbon and hydrogen atoms - hydrocarbons. Due to various physical attraction
forces, they form densely packed structures called pseudo compounds which can further organize into
clusters or associations [8]. These structures are relatively stable and during air/fuel mixing process,
oxygen atoms cannot penetrate into their interior. The access of appropriate quantities of oxygen to the
interior of these molecular groups (associations) is thus hindered. This result in the incomplete
combustion of fuel in the interior of such associations and causes the formation of carbon particles and
carbon monoxide as well as increased quantities of hydrocarbons emitted into the environment [9].
It is now well accepted that a hydrocarbon fuel can be polarized by exposure to external force such as
magnetism. The effect of such magnetism is the production of a moment created by the movement of the
outer electrons of a hydrocarbon chain moving the electrons into states of higher principal quantum
number. This state effectively breaks down the fixed valance electrons that partake in the bonding process
of the fuel compounds. These states create the condition for freer association of fuel particulars. In so
doing, the hydrocarbon fuel becomes directionalized or aligned which does not necessarily create new
hydrocarbon chains but more explainable aligns the conduced magnetic moment into a dipole relationship
within itself. This magnetic alignment then permits rapid bonding with the respective oxidizing media.
The result of which is, of course, more complete and rapid burning of the hydrocarbon fuel [10, 11].
Hydrocarbon molecules treated with a high magnetic field tend to de-cluster forming smaller
associates with higher specific surface for the reaction with oxygen leading to improved combustion. In
accordance with van der waals discovery of a weak clustering force, there is a strong binding of
hydrocarbons with oxygen in such magnetized fuel, which ensures optimal burning of the mixture in the
engine chamber. The consequence of treating fuel with a high magnetic field is improved combustion of
fuel and consequently increased engine power as well as reduced fuel consumption. An additional
consequence of improved fuel combustion is reduced emissions of carbon particles, carbon monoxide and
hydrocarbons [8, 12]. In our study, focus has been laid on the understanding of magnetic action modes
which have led to the fuel economy and reducing exhaust emissions in engine applications.
Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338 329
De-cluster of fuel
Hydrocarbons have basically a "cage like" structure. That is why during the combustion process
oxidizing of their inner carbon atoms is hindered. Furthermore they bind into larger groups of pseudo-
compounds. Such groups form clusters (associations). The access of oxygen in the right quantity to the
interior of the groups of molecules is hindered and it is this shortage of oxygen to the cluster that hinders
the full combustion [13]. The exhaust should theoretically contain carbon dioxide, water vapour and
nitrogen from air, which does not participate in the combustion. Practically the exhaust gases contain CO,
H2, HC, NOx and O2. In reality, complete combustion of fuel is never achieved and the incompletely
oxidized carbon is evident in the form of HC, CO or is deposited on the internal combustion chamber
walls as black carbon residue. Hydrocarbon fuel molecules treated with the magnetic energy tend to de-
cluster, creating smaller particles more readily penetrated by oxygen, thus leading to better combustion
[14]. They become normalized & independent, distanced from each other, having bigger surface available
for binding (attraction) with more oxygen (better oxidation). In accordance with van der Waals' discovery
of a weak-clustering force, there is a very strong binding of hydrocarbons with oxygen in such
magnetized fuel, which ensures optimal burning of the mixture in the engine chamber [2].
In our study, focus has been laid on the understanding of magnetic action modes which have led to the
fuel economy and exhaust emission reduction in engine application (10 pt) Here introduce the paper, and
put a nomenclature if necessary, in a box with the same font size as the rest of the paper. The paragraphs
continue from here and are only separated by headings, subheadings, images and formulae. The section
headings are arranged by numbers, bold and 10 pt. Here follows further instructions for authors.
2. Methodology
The effect of the magnetic field on fuel (gasoline Iraqi) used in the engines and its impact on the
amount of consumption, as well as emission of exhaust gases, the appropriate method was examined. We
include below the description of the materials and equipment used.
2.1. Magnetic devices
Four magnetic devices used in this research were manufactured in the laboratories of the Water
Research Centre / Ministry of Science and Technology. Each device contains the number of permanent
magnets arranged alternately in multiple stages. The magnetic intensities of those magnets are (2000,
4000.6000, 9000) Gauss. Figure (1) represents one of them.
Fig. (1). a photograph of one of the magnetic devices
2.2. Engine
Two-Stroke Engine with spark ignition, Chinese origin TWP20C with a capacity of up to 5.5 hp was
selected, for being used in most Iraqi homes for the implementation of the experiments. An external tank
330 Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338
includes a volumetric scale and valve was connected instead of the main reservoir of the engine so as to
measure the amount of fuel consumed during operation and for each experiment.
2.3. Fuel
The fuel which provides by gasoline filling stations to the cars and small generators was used in our
current research.
2.3. Procedure
Figure (2) represents a photograph of the fuel magnetization unit used in the implementation of the
experiments.
Periodic inspection of the engine parts for each experiment.
Three accelerated rotation of the engine (3500, 4500, 5000) r.p.m, was taken, which representing an
initial speed and low, medium and higher than the other so as to know the amount of fuel consumption
in each of these speed at all magnetic intensities.
Start up the engine after putting a certain amount of fuel in the external tank, and set the selected speed
for the experiment. Process will continue operating for two hours and for each test, during which the
exhaust gas was measured at several times for accuracy. After that, calculate the amount of consumed
fuel in the end of the experiment through the rankings is installed on the external tank of the engine.
Repeat this process for the second speed to know the amount of consumed fuel and the amount of
exhaust gases.
Repeat the process in paragraph (3) after install the magnetic device with intensity 2000 Gauss on the
fuel line, as well as re-install the same speed because it will increase after install the magnetic device.
The exhaust gases during operation were measured, as well as the amount of consumed fuel after the
end of the operation. The amount of consumed fuel after the installation of the magnetic device was
deducted from the quantity before the installation of the magnet to know the quantity saved, and the
same principle applies to the exhaust gases.
Repeat the process in paragraph (5) for each magnetic intensity and also for the three above speed.
Fig.2. a photograph of the fuel magnetization unit (1. Engine, 2. Magnetic device 3. Measuring device for exhaust
gases, 4. Fuel tank, 5. Gas sensor, 6. Valve, 7. Flexible tube for fuel)
Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338 331
2.4. Test and measurement equipment
Samples up to 100 ml of fuel before and after the process of magnetization were taken for each
magnetic intensity and to measure the absorption spectrum of the infrared device using the IR prestige-
21-SHIMADZU range (400-4000) 1/ cm.
As well as, similar samples to measure the spectrum of UV absorption, using a device
UV-1650PC/UV-VIS spectrophotometer from SHIMADZU.
Surface tension of the fuel before and after the magnetization was measured for all intensities, where
the sample size of 50 ml was taken and examined by a device KSV Instruments LTD-series SIGMA 70,
using (Wilhelmy plate). The gases CO, CH and CO2 were measured by analytical gases device type
AVL, made in AUSTRALIA.
3. Results and discussion
3.1. Effect of magnetic field on fuel consumption and exhaust gases
Figure 3 represents the amount of fuel consumed with the intensity of the magnetic field for three
different engine speeds. The amount of untreated fuel consumed in the engine for the three speeds were
(1350, 1560, 1775) ml, respectively. While these values decreased with the use of a magnetic field, where
the amount of consumed fuel treated by using high magnetic field intensity less than that treated by using
low intensity.
Fig. 3. Reducing the amount of consumed fuel with increasing magnetic field intensity
To illustrate the percentages of fuel saving with the magnetic intensity for the mentioned three speeds
above clearly, these percentages were calculated by deducting the amount of fuel consumed after
treatment from the amount before treatment and converted to a percentage scale, as illustrated in the
Figure 4
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
0 2000 4000 6000 8000 10000
Magnetic intensity (Gauss)
Fuel consumption (ml)
--- 5000 r.p.m
--- 4500 r.p.m
--- 3500 r.p.m
332 Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338
5
6
7
8
9
10
11
12
13
14
15
2000 4000 6000 8000 10000
Magnetic intensity (Gauss)
Saving percentage %
--- 5000 r.p.m
--- 4500 r.p.m
--- 3500 r.p.m
Fig. 4. Increased rate of fuel saving with increasing magnetic field intensity
The fuel saving percentage was ranged between (9-14) % depending on the magnetic field intensity, as
well as the engine speed. In the same context, the percentages of fuel saving but with increasing engine
speed for three magnetic intensities, are described in Figure 5. The percentage was greatest in the high
speed and high intensity.
Fig. 5. Increased rate of fuel saving with increasing engine speed
The percentage of the exhaust gases which measured during the operation of the engine, for three
speeds, before and after magnetic treatment was shown in Figure 6 and Figure 7. It was found that the
reducing percentage of the gases (HC, CO) up to (30, 40) % respectively, but the percentage of CO2
increased about 10%, as shown in the Figure 8.
5
6
7
8
9
10
11
12
13
14
15
3000 3500 4000 4500 5000 5500 6000
r.p.m
Saving percentage %
--- 000 G
--- 6000 G
--- 4000 G
Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338 333
0
0.5
1
1.5
2
2.5
3
3.5
4
0 2000 4000 6000 8000 10000
Magnetic intensity (Gauss)
CO Reduction %
--- 5000 r.p.m
--- 4500 r.p.m
--- 3500 r.p.m
0
10
20
30
40
50
60
70
80
0 2000 4000 6000 8000 10000
Magnetic intensity (Gauss)
HC reduction %
--- 5000 r.p.m
--- 4500 r.p.m
--- 3500 r.p.m
Fig. 6. Decrease rate of CO gas with magnetic intensity
Fig. 7. Decrease rate of unburned hydrocarbons HC with magnetic intensity
334 Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338
Fig. 8. Increase rate of CO2 gas with magnetic intensity
Magnetization of fuel, breaks down the bonds between hydrocarbon chains which results in decreased
density, surface tension and, hence smaller particulars and droplets during atomization or injection within
an internal combustion engine. Smaller particles and droplets Causes increased evaporation rates,
improved mixing of fuel and oxidizer, and improved promotion of oxidation. The net effect is an increase
in the rate of combustion, an increase in power, and reduced pollutants.
Increased oxidation of the hydrocarbon fuel causes several effects. Faster and more complete oxidation
results in more rapid and more complete combustion of the fuel. Faster and more efficient combustion
creates a more concentrated and more forceful driving force on the pistons of an internal combustion
engine, albeit for a shorter duration of time. Typically, this result in the desirable effect of increasing the
engine's revolutions per minute (rpm) for the same amount of fuel burned. The net effect is increased
power and/or a corresponding decrease in fuel consumption for a given power output
3.2. Effect of magnetic field on microstructure of fuel
As are known, the infrared spectrum of absorption of fuel provides an insight into its molecular
structure, because the wavelengths of the movement and vibration of these molecules are within the
ranges of wavelengths of this ray. To see the effect of magnetic field on these molecules a sample size of
500 ml of fuel have been taken and exposed to a magnetic field with different intensities (2000,
4000.6000, 9000) Gauss without retention time within the system of magnetization. About 100 ml of the
above sample were taken, as well as those, but without magnetization to be examined by infrared
spectrometer (FTIR). Figure 9 shows the infrared absorption spectra of treated and untreated fuel.
The coloured spectra, red, blue, violet, black and green shown in the Figure 9 indicate to the infrared
absorption peaks and its strength and position of the fuel under the influence of above magnetic
intensities. From this Figure we see that the strengths of absorption peaks of treated fuel at each magnetic
intensity increased in the region of (400-4000) cm-1, but their positions or frequencies do not change,
when compared with that of untreated fuel. This shows that the polarized feature and transition dipole
moments of molecules are enhanced relative to that of untreated fuel due to the displacements of atoms
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0 2000 4000 6000 8000 10000
Magnetic intensity (Gauss)
CO
2
Increas %
--- 5000 r.p.m
--- 4500 r.p.m
--- 3500 r.p.m
Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338 335
0 500 1000 1500 2000 2500 3000 3500 400
0
1/cm
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
Absorbance
----- 9000 Gauss
----- 000 Gauss
----- 000 Gauss
----- 000 Gauss
----- 0000 Gauss
constituting fuel molecules and change in the magnetic moment of molecules interaction under the action
of the magnetic field.
Fig. 9. Variation of strengths of infrared absorption peaks of fuel with magnetic intensity
Because the molecular attraction energy of non polar hydrocarbon is determined by group vibrational
frequency, so a conclusion can be easily reached that the higher the frequency the lower the absolute
value of molecular attraction energy, or, the lower the group attraction energy. Thus, it can be deduced
that the molecular attraction force among hydrocarbons decreases after they are magnetized. This is why
the property indices of hydrocarbons, such as viscosity and surface tension which are influenced by the
molecular attraction force, decline after the hydrocarbons flow through magnetic field.
It is well known that the visible and ultraviolet light radiated by matter is related to the transitions of
energy levels and to changes in the state of electrons. Therefore, to study the features of these spectra of
visible and ultraviolet light of fuel, it is useful to reveal and exhibit the properties and mechanisms of the
influence of magnetic field on electronic motions and atomic structures in the fuel molecules. Thus, here
we first measure the spectra of visible and ultraviolet light for a fuel treated with different magnetic
intensities and compared with these of untreated fuel as shown in Figure 10.
336 Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338
-0.5
0
0.5
1
1.5
2
2.5
270 290 310 330 350 370
Wave length (nm)
Absorbance
--- control sample
--- 4000 G
--- 9000 G
Fig. 10. Absorption spectrum of ultraviolet light for fuel magnetized with different magnetic intensities
This Figure shows clearly that the intensity in the absorption of ultraviolet light for magnetized fuel
increases with increasing wave length of light in the region of 280-360 nm relative to that of untreated
fuel. This means that the externally magnetic field greatly changes the feature of ultraviolet absorption of
fuel. This means that the externally applied magnetic field greatly changes the feature of ultraviolet
absorption of fuel.
It is evident that the ultraviolet absorption strength increases remarkably after the aromatic
hydrocarbons have been magnetized. This means that the transition probability of electrons in the -
bond conjugated system among different energy levels has become higher. Since the transition of the
bond electrons from the ground level to the excited level is the main process of molecule radicalization.
This may enhance the splitting of the C=C bonds in the aromatic rings in the course of combustion under
intense actions of light and heat, and therefore the oxidation of the aromatic rings can be accelerated and
easily completed thoroughly. As a result, the combustion efficiency of aromatic hydrocarbons would be
boosted, which gives rise to the noticeable increase.
Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338 337
0
0.5
1
1.5
2
2.5
3
3.5
4
0 2000 4000 6000 8000 10000
Magnetic intensity (Gauss)
Surface tension reduction rate %
3.3. Effect of magnetic field on surface tension of fuel
Fig. 11. Change in surface tension of the fuel with the intensity of the magnetic field.
Figure 11 displays the relationship between the decrease rates of the surface tension of magnetized fuel
and the applied magnetic intensities. The results show that, after magnetized, the surface tension of the
hydrocarbons decreases. However, the decrease rates or the decrease magnitudes do not increase
accordingly very well as the strength of the magnetic field increases. At some certain magnetic fields, the
surface tension decreases comparatively considerably while at others it decreases comparatively
unnoticeably. So, it can be easily concluded that the surface tension of the hydrocarbons decreases
fluctuately with the increase of the magnetic field intensity. The value of surface tension is determined
not only by molecular attraction force but also by molecular orientation state on the liquid surface. May
be the oriented distribution state of hydrocarbon molecules on the liquid surface must have changed after
they have been magnetized, and that the oriented distribution state must have changed differently at
different magnetic field strength. This can result in high decrease rate, and the fluctuation of the decrease
of surface tension.
4. Conclusion
When fuel is exposed to a magnetic field, we find that its properties are changed.
Magnetic treatment does not need energy and thus be economically feasible.
Change some properties of the fuel by the magnetic field, and take advantage of some of the
applications that belong to the industry and the environment.
Increase the efficiency of most equipment and machinery that using hydrocarbon fuel and reduce
consumption up to 14%.
We can understand the mechanism of magnetization of fuel through the impacts of external magnetic
field in the microscopic structure, which is the displacement and polarize the fuel molecules.
Clear changes in the value of surface tension of the fuel, which used in this study and employment of
these changes in the applied fields.
Reduce the amount of environmental pollutants in the exhaust gases up to 40%
338 Ali S. Faris et al. / Energy Procedia 18 ( 2012 ) 327 – 338
5. Reference
[1] P. Kulish, "Seminar Report on Fuel Energizer" (1984),pp. 1-25
[2] P. Govindasamy and S. Dhandapani, "Experimental Investigation of Cyclic Variation of Combustion
Parameters in Catalytically Activated and Magnetically Energized Two-stroke SI Engine" Journal of
Energy & Environment, Vol. 6, , (2007), pp.45-59
[3] S. Mingdong et Combustion Efficiency of Magnetized Petroleum Fuels, Chinese
Science Bulletin, (1984), 3.
[4] J. C. L. Cummins, "Early IC and Automotive Engines" SAE paper 760604, Society of Automotive
Engineers, Warrendale, Pennsylvania, USA, (1976),pp. 18-26.
[5] R. K. Kiran, K. S. Muley, "Two Stroke Cycle Engine Performance and Fuel Treatment Devices"
Overdrive-An Automobile Magazine, New Delhi, , (2006), pp. 23-28.
[6]
Transportation (China) , (1990).
[7] C Oil by A Strong Magnetic Field and Its
[8] H. Guo, Z. Liu, Y. Chen and R. Yao,"A Study of Magnetic effects on the Physicochemical Properties
of Individual Hydrocarbons" Logistical Engineering College, Chongqing 400042, P.R China(1994),
pp.216-220.
[9] P. Govindasamy, S. Dhandapani, "Experimental Investigation of the Effect of Magnetic Flux to
Reduce Emissions and Improve Combustion Performance in a Two Stroke, Catalytic-Coated Spark-
Ignition Engine" International Journal of Automotive Technology, Vol. 8, No. 5, (2007),pp. 533-542
[10] I. Pera, P. Pines, "Magnetizing Hydrocarbon Fuels and Other Fluids" U. S. Patent No. 4716024,
(1987).
[11] C. A. Okoronkwo , C. C. Dr. Nwachukwu, L.C. Dr. Ngozi and J.O. Igbokwe, "The Effect of
Electromagnetic Flux Density on the Ionization and the Combustion of Fuel (An Economy Design
Project)" American Journal of Scientific and Industrial Research, ISSN: 2153-649X
doi:10.5251/ajsir.(2010).1.3.527.531
[12] , (1994).
[13] N. Nedunchezhian, S. Dhandapani, "Experimental Investigation of Cyclic Variation of Combustion
Parameters in A Catalytically Activated Two Stroke SI Engine Combustion Chamber", SAE-India,
Paper, (1999) , 990014, pp. 1-16
[14] R. R. Bowker, "Permanent Magnet Design Guide", Magnet Sales and Manufacturing & Co,
USA,(2000), pp. 11-67.
