Chapter
To read the full-text of this research, you can request a copy directly from the author.

Abstract

Water is particularly important substance in papermaking. It plays essential role in fibers transportation, equipment cleaning, lubrication, cooling and in development of a product quality. A tendency to reduce the fresh water consumption in paper production is economically and environmentally justifiable but it must be emphasized that strict closing of water system in paper mill has significant negative impact on several technological operations. High water temperature, as well as increased content of suspended and dissolved solids in water system of a paper machine is examples of major consequences of closing the water loop. As a result, serious problems may cause e.g. paper defects, loss of product quality and problems with run ability of a paper machine. Situation becomes even worse when recycled raw materials are used. Hence, methods of fresh water usage reduction in papermaking are very complex issues and usually depend on the degree of closure. Equilibrium between the advantages and the disadvantages relevant to water consumption restrictions should be established. The acceptable level of water loop closure will depend on the several factors e.g. paper quality required, raw materials used, chemical additives, equipment and staff education. The objective of this chapter is to present main problems related with reduced water consumption in paper industry, to describe the further possibilities of water usage reduction and consequences of this operation for the technological process and for the environment.

No full-text available

Request Full-text Paper PDF

To read the full-text of this research,
you can request a copy directly from the author.

... Some of the water can be used in closed loop; however, a significant reduction of water consumption is not possible without compromising the quality of the paper. The highest amount of fresh water is used in the chemical pulp making process (40%) and in paper machines (35%) [161]. In 2018, the European paper industry consumed 3481 million m 3 of water, 90% of which was later returned to the source [159]. ...
... The most effective way of reducing fossil fuel consumption is to use renewable energy sources. The less processed the paper product is, the lower its environmental impact; speciality paper, highly bleached, with chemical additives or surface treatments can increase water and energy consumption several times compared to, eg, brown packaging paper [161]. ...
Article
The article presents paper-based building products with cellulose fibres as the main component of natural origin. Cellulose is the most common natural polymer on the planet, and its resources are considered to be inexhaustible. The contemporary era of paper architecture began in the mid-1980s when Japanese architect Shigeru Ban for the first time used paper tubes as a structural element in an architectural object. However, there is still a lack of complementary research to embrace paper products as a building material from the mechanical, thermal and acoustic point of view with the respect to the methods of lamination and impregnation, and their impact on pro-ecological features of the material. The aim of the article is to review accessible knowledge regarding different properties of paper-based products in the context of their implementation as a building material: 168 records from the fields of architecture, mechanics, building physics, acoustic, and chemistry have been reviewed. The presented analysis identifies the knowledge gaps and the direction for further research and development of paper as a building material.
... Concerns over water conflicts between human beings and ecosystems are thus growing at multi-scale governmental jurisdictions and industrial sectors (Ene et al., 2013). Particularly, in many regions of eastern China, a large quantity of water is now consumed by many industries such as pulp and paper mills to maintain economic boom (Olejnik, 2011). Such a large amount of water consumption is reducing limited available water resources, threatening diverse indigenous ecosystems, and potentially resulting in degradation of the ecosystems (Yang et al., 2004). ...
... At present, annual paper production approximately reaches 400 Mt (CEPI, 2010). Generally, annual consumptions of paper products can be considered as direct reflection of economic development for a country (Olejnik, 2011). Totally, North America, Europe and Asia account for over 90% of the global paper consumption. ...
... Despite their high importance, water resources are constantly threatened by anthropic activities, such as agricultural, industrial, or recreational activities. Therefore, new practices and behaviours could be adopted by the users to reduce water consumption, as well as to improve the efficiency of their domestic uses (e.g., [7-10]), services (e.g., [11,12]), agriculture (e.g., [13,14]) or industrial use (e.g., [15][16][17][18][19]). ...
Article
Full-text available
This work proposes a comprehensive methodology for evaluating fissured hard-rock groundwater resources through an integrative approach based on fieldwork techniques, Geographic Information System (GIS)-based mapping, geospatial analysis and multiple-criteria decision analysis (MCDA). The study sites comprise distinct geological settings and geographic contexts, i.e. granitic rocks (NW Portugal) and metasedimentary rocks (SW Spain). A similar methodological approach was used in both areas to compare and assess the methodological approaches’ effectiveness. The cartographic, field, and laboratory data were analysed through GIS overlay and multi-criteria spatial analysis. This GIS-integrated analysis allowed the calculation of the Infiltration Potential Index (IPI) and groundwater vulnerability indexes: GOD-S, DRASTIC-Fm, SI and DISCO, as well as the development and improvement of the hydrogeological conceptual models. At the Entre-os-Rios site (NW Portugal), the IPI index showed that the most favourable areas for infiltration are the fractured granitic regions, where the slope has the lowest values, combined with forest areas. The recharge values are around 70 to 90 mm/year. Considering hydraulic connection with the borehole data, the DISCO index identified the geostructures with the most important trending to NNE-SSW, NE-SW and WNW-ESE in the area. The highest IPI values were identified in the regional aquifer quartzite unit at Herrera del Duque (SW Spain). The recharge values are around 60 to 80 mm/year. The DISCO index identified zones where discontinuities have a higher hydraulic connection to the borehole, mainly trending NW-SE and NE-SW. The models developed could be helpful for decision-making and sustainable water resources management regarding the planning of hydrogeological investigations, delineating potential contamination areas, and the definition of catchment protection areas.
... In 2020 it accounted for 60.5% of total energy consumption [17]. Modern paper mills require 10-50 m 3 of water for each tonne of produced paper, however, these numbers are lower for unbleached and recycled papers [18,19]. ...
... Thus, making both fresh and recycled papers are expensive in terms of burden on the environment and consumption of energy, water, materials and time . In fact, production of one ton of recycled paper costs 5000 gallons of water [1], 2250 kW of energy [2] and emits 950 Kg of CO 2 [3]. On an average 66% papers printed are considered waste which unnecessarily increases pollution. ...
Article
Full-text available
While paper continues to remain one of the most widely used materials for writing and printing and while its demand continues to grow, the environmental cost of using paper is rather huge. Paper is made by extracting the cellulose fibres from wood, to meet the demand of which, trees in large number are felled. Making paper requires huge quantity of water, energy and also toxic chemicals. In fact, paper is considered the 3rd largest industrial polluter of air, water and soil. Yet, a viable alternative to paper doesn't exist. Inspired by the inherent ability of many natural surfaces to keep themselves clean, we have made a reprintable paper which can be used over 50 cycles. It is prepared by casting crosslinkable silicone on a porous template, leading to hierarchical random surface features having dimensions ranging from tens of nano-meter to hundreds of micrometers. On this surface, ink particles of wide-ranging sizes and surface chemical characteristics adhere via intermolecular interactions. However, unlike conventional papers, in which particles get mechanically trapped inside the porous network of the cellulose fibres, here the ink particles remain accessible for cleaning via gentle scrubbing with a rough surface, soaked with a suitable liquid. Thus, this paper continues to remain both cleanable and printable.
... Cellulose is a renewable resource and, as paper building structures are much lighter than conventional ones, their production is less energy-consuming and generates less carbon dioxide than traditional building materials manufacturing (Hammond and Jones 2019). However, for the credibility of the given information, it has to be stated, that paper production requires the use of a large amount of water -approximately 10-20 m 3 of freshwater and 100-150 m 3 of process water per Mg of paper (Olejnik 2011). Contemporary manufacturing methods aim to reduce the amount of used water and re-use the wastewater in the closed-loop. ...
Article
Paper and cardboard elements can be used as a pro-ecological building material. To meet the safety and usage requirements paper elements need to be impregnated, however, most impregnation methods have a negative impact on the environmental performance of the elements. This article describes research that was conducted in order to determine the most effective technique of paperboard impregnation against water and humidity. Particular attention was given to biodegradable coatings, as several oil-based and wax-based wood impregnates were used. The samples were tested for 24 hours in immersion and for 48 hours in high air humidity. Water uptake (measured by the change in mass and thickness), delamination and deformation of samples were monitored. As a result, the basic characteristic of the tested impregnation methods was established – water and water vapour absorption, deformation or delamination after immersion. The lowest water and water vapour absorption was observed in samples impregnated with composed coatings of oils and waxes.
... The water consumption of today's papermaking processes varies between 5 and 20 m 3 /t, and for some special grades, the consumption can be as high as 80 m 3 /t. [111] Waste water is typically treated at the waste-water treatment plant, where key pollutants are removed by different methods. Separation technologies include physicochemical methods like sedimentation, flotation, coagulation, precipitation, Figure 17. ...
Article
Full-text available
Aqueous foam can be used as a transfer medium to form lightweight materials from natural and man-made fibers together with other types of raw materials. This review discusses mechanisms that underlie the forming process and thus influence physical properties of formed fiber networks such as microporous structure, strength behavior, and transport properties. Homogeneous fiber materials can be formed from versatile raw materials, which makes the technology suitable for a vast range of product applications. An intriguing feature of the method is that the wet foam characteristics provide an additional tool to tailor the performance of the dried material. Understanding foam rheology and how that is affected by added fibers is important in developing the forming process. We introduce both fundamental foam properties and practical forming methods, and show how the material properties are affected by the foam–fiber interaction. The basic features of an industrial production process are also described. The potential material properties are compared against key requirements in typical product applications.
Article
Full-text available
Water is a critical resource for all of manufacturing. As such, mitigating risks to the supply of water to manufacturing plants facilitates maintaining a vital manufacturing sector. Reductions in water use through water efficiency is one method for mitigating risk, however little is known about its potential in the United States (U.S.) manufacturing sector. Herein, we address this gap and calculate the water reduction potential in U.S. manufacturing from commercially available water efficiency opportunities specific to the manufacturing sector. A list of water efficiency measures specific to the manufacturing sector is compiled and applied to estimates of U. S. manufacturing water withdrawals. The energy and carbon dioxide equivalent (CO2e) emission impacts from implementation of these measures are also quantified to better inform the resource, environmental, and economic trade-offs from implementation of these measures. We find that the water savings potential from the evaluated measures is up to 60 percent of U.S. manufacturing water withdrawal for certain subsectors, with the energy and emissions impact dependent on the measure. Further, we calculate the levelized cost of conserved water for several water efficiency measures (-4,000to4,000 to 85/thousand m3 , where negative values indicate net cost savings and positive values indicate net cost expenditures) and compare them to the levelized cost of alternative water sources (600to600 to 3,400/thousand m3 ). The results show significant opportunities for water and energy use reductions at levelized costs at least one order of magnitude lower than alternative water supplies, with some being revenue-generating.
Article
Water plays several essential roles in paper manufacturing. It serves as a suspending medium and a swelling agent for the fibres, dispersing and forming them into a uniform sheet during the initial stage of the papermaking process. It also serves as the solvent for a variety of chemicals and additives to adjust product quality. Water reclamation has always been a momentous task in the pulp and paper (P&P) industry. The main driving forces for the adoption of process water and wastewater treatment technologies are environmental regulations, costs of wastewater discharge and the high cost of freshwater. Recent developments have made it possible to not only reduce water consumption and environmental impacts, but also to recover treated water and valuable compounds such as fibres, making water recycling technologies cost-efficient. Thus, the economic viability of these technologies has played an important role in their application. The technologies applied, the level of reduction in water consumption and the extent of water recycling are different for each mill, since the quality of whitewater and wastewater varies depending on the raw materials and products. The maintenance of the balance between partial equilibria of process variables such as water flowrates, pulp consistency, physiochemical, thermal and microbiological properties through water management is important for maintaining efficient water use and lowering the need for consumption of additional fresh water.
Article
Salinity Gradient Power-Heat Engine is an innovative technology able to convert very low-temperature heat into electricity. Energy and economic benefits could be achieved by integrating this technology into cogeneration plants, where the exploitation of waste heat available during the operation could increase the revenues arising from “High-Efficiency” labels. For the first time, this paper proposes two potential applications in this field, and three illustrative case studies are purposely investigated. In the first case study, a salinity gradient-heat engine converts the waste heat available from a cogeneration plant serving an industrial process. In the second case study, a salinity gradient-heat engine is integrated into a cogeneration plant coupled to a district network. In the third case study, the possibility to reduce the size of a cogeneration plant by coupling this engine with a heat pump is investigated. The analysis relied on simplified models of the integrated systems which were numerically solved. Results for the first case study show an increase of 10.6% in revenues from the high-efficiency support mechanism and electricity selling. In the second case study, the primary energy saving increases from 8.7% up to 10.1%, thus achieving the threshold value for “High-Efficiency” eligibility. In the third case study, the heat engine allows to reduce up to 12.1% the nominal capacity of the prime mover. A prospective analysis of the integration of salinity gradient-heat engine in cogeneration plants is thus presented, and it poses a fundamental reference for future integration of this novel technology into these energy systems.
Article
Full-text available
Closure of water circuits in papermaking is of vital importance for achieving a more sustainable and economic manufacturing of paper. The most important limiting factor for a further closure is the accumulation of dissolved and colloidal materials (DCM). The extent to which DCM can become enriched in the water depends not only on how many times water is reused but also on the degree to which this matter becomes reattached to the fibers and other solid components of the paper furnish. This study analyzes the accumulation of the most typical contaminants in newsprint (NP) and light weight coated (LWC) paper production. Results show that the release of DCM depends on the present contaminant load in the waters: higher at lowcontaminant load and lower at high contaminant load. A simulationwas carried out to analyze the differences between assuming a constant and a variable release of contaminants to waters. Important differences were observed, especially at low fresh water consumption for those species with a major affinity for the fibers.
Article
The compositions of white water from a newsprint machine and model recycled white waters (1-5 times) were determined. The effects of these white waters on paper properties were compared and related to differences in their composition. It was found that the level of total dissolved and colloidal substances and the concentration of each group of the components within the while water increased sequentially after each recycle step. The dissolved and colloidal substances were primarily composed of carbohydrates, lipophilic extractives and lignins. A highly recycled white water and a regular mill white water were used to make handsheets. The strength, optical, surface and wet web properties of the handsheets were significantly impaired when white water was used in place of distilled water during handsheet preparation. Lipophilic extractives reduced interfibre bonding and sheer consolidation resulting in a decrease in handsheet density of around 10%, a decrease in tensile strength of 20-30% and, at lower concentrations of dissolved and colloidal substances, increased porosity and rates of water absorption. These effects were partially offset by increasing levels of colloidal material which resulted in significant reductions in porosity and snte of water water absorption. Higher concentrations of lignin-derived material increased light absorption of the handsheets with corresponding brightness decreases of up to 10 points ISO. The presence of resin and fatty acids in the white water decreased water surface tension with a concurrent decrease in wet-web strength and papermachine runnability.
Article
Product quality together with uptime and speed constitute paper machine efficiency. The role of the wet end system in this is to constantly and promptly provide the right quality stock to the machine. The approach flow system can contribute to efficiency by stability, agility, cleanliness, gaslessness and robustness of the system. According these criteria a compact hydraulic wet end system with centrifugal backwater degassing can give considerable advantage compared to a traditional one. The paper briefly presents the compact system and discusses experience obtained with twenty industrial references. The system features composing of the stock just before feeding it to the papermachine, centrifugal degassing hydraulic distribution of the backwater and related solutions. The good stability partly depends on better working conditions for the process pumps, with elevated suction head anda degassed fluid. This is further improved by the absence of instability and low intensity turbulence in tanks and silos. The compact system reacts faster and more precise than a voluminous one permitting easy grade changes and exact control. The early degassing eliminates formation of microstickies enhancing the cleanliness effect of fast flow in the hydraulic system. Centrifugal degassing also gives a headbox gas-content in line with that of vacuum degassing. Simple system architecture together with fast and precise control response make the system transparent and easy to operate. Together these features have yielded efficiency increases between three and more man ten percent.
Article
The optimization of white water system design, improves the runnability and lowers the operating cost of the paper and pulp mills. The white water systems are designed to minimize fresh water consumption, reuse clarified/unclarified white water, use filtration equipment and storage efficiently, and to minimize loss of chemical and fiber. The type of equipment used for clarification and reuse, arrangement and performance of the equipment, and control strategies affect the optimal closure of white water system.
Article
A mathematical model has been developed to predict how the dissolved solids will build up after the white water, system of a paper machine is closed to different degrees. In the closing of a mill system, any reduction in the paper machine water consumption will be accompanied by an increase in the dissolved and colloidal solids in white water. According to the model, the dissolved solids coming into the system will not build up endlessly, no matter how many times they are recycled and how tightly the system Is closed. The final equilibrium concentration of any dissolved solids will be less than the flow-proportional average concentration of that species in all outside water sources entering the system. Laboratory experimental results, were in fair agreement with the model predictions.
Article
The stepwise development of system closure strategies in newsprint mills is analyzed using a novel method for the hierarchical development of process flow diagrams. Recent work on paper machine modeling, mill experimentation, validation of simulations, networks analysis and dynamic characterization is reviewed. Closure strategies of process and non-process networks which have been developed for or tested in actual mills are discussed. The needs for R&D work on contaminant-specific distributed extraction techniques and on the establishment of mill-validated contaminant concentration thresholds are examined.
Article
For a hardcopy of this report, printed in the Netherlands, an estimated 200 litres of water have been used. Water is required during different stages in the production process, from growing wood to processing pulp into the final consumer product. Most of the water is consumed in the forestry stage, where water consumption refers to the forest evapotranspiration. The water footprint during the manufacturing processes in the industrial stage consists of evaporation and contamination of ground- and surface water. In this report we assess water requirements for producing paper products using different types of wood and in different parts of the world. We quantify the combined green and blue water footprint of paper by considering the full supply chain; we do not include the grey water footprint in this study. The water footprint of printing and writing paper is estimated to be between 300 and 2600 m3/ton (2-13 litres for an A4 sheet). These figures account for the paper recovery rates as they currently are. The exact amount depends on the sort and origin of the paper used for printing. Without recovery, the global average water footprint of paper would be much larger; by using recovered paper an estimated 40% is saved globally. Further saving can be achieved by increasing the recovery percentages worldwide. For countries with a low recovered paper utilization rate a lot of room for reduction still remains. Some countries such as the Netherlands, Spain and Germany already use a lot of recovered paper. In addition, the global water footprint of paper can be reduced by choosing production sites and wood types that are more water-efficient. The findings presented in this report can be helpful in identifying the opportunities to reduce water footprints of paper consumption. This report also shows that the use of recovered paper may be very helpful in reducing water footprints.
Article
Although the industry has become more environmentally friendly, it needs to overcome social, economic, and scientific obstacles to achieve additional progress
Article
The problem of water use in industrial sectors is analyzed in the context of sustainability, and the manufacturing process as one of the most important water consumers is scrutinized. Some practices of water conservation and reduction of water consumption, as well as the implementation of advanced treatment processes for wastewater recycling are considered under the general aspect of process integration and control in order to minimize environmental discharges. Reduction of effluents in papermaking processes are discussed as well as preventative approaches. It is emphasized that four groups of methods can be applied in order to minimize water consumption: process changes, water reuse, regeneration reuse and regeneration recycling. Minimizing the water consumption and thus reducing the hydraulic load may help to improve effluent treatment, reduce operating costs and, when subsequent disposal is to sewers, minimize effluent disposal charges. The data presented show that initially producing less effluents will reduce the demands on the effluent treatment plant and thus save both money and efforts. Separation techniques for minimizing effluents and effluent loads are presented, as well as potential practices to ensure a sustainable use of water, grouped as short term and long term measures. Prevention measures for water consumption in a Romanian paper mill are considered and discussed in relation with best available techniques (BAT), taking into account both economical and environmental benefits.
Article
Although the industry has become more environmentally friendly, it needs to overcome social, economic, and scientific obstacles to achieve additional progress.
Membrane filtration with OptiFilter
  • Metso Paper
Metso Paper (2010) Membrane filtration with OptiFilter. http://www.metso.com/MP/ Marketing/vault2mp.nsf/BYWID2/WID-030410-2256C-B49AE/$File/OptiFilter_CR_12_2003. pdf?openElement. Accessed 19 Aug 2010
The BREF in the pulp and paper industry: BAT for an industry with a large variety of raw materials and products
  • M Suhr
Suhr M (2000) The BREF in the pulp and paper industry: BAT for an industry with a large variety of raw materials and products. In: Proceedings of European conference on the Sevilla process: a driver for environmental performance in industry, Stuttgart, 6 and 7 Apr 2000
Successful reduction in fresh water consumption with OptiFilter membrane
  • K Pohjalainen
Pohjalainen K (2005) Successful reduction in fresh water consumption with OptiFilter membrane. Fiber Pap 7(3):20-21
Closing the water cycles - how far can we go? Metso Paper Technology Days Meeting
  • M Huhtamaki
Huhtamaki M (2003) Closing the water cycles - how far can we go? Metso Paper Technology Days Meeting, Helsinki
Joint publication: Practical Water Management in Paper and Board Mills. Produced by the Environmental Technology Best Practice Programme
Industrial Footprint Project (2010). http://www.ecy.wa.gov/programs/swfa/industrial/pdf/ archiveIndFootprint/Oct16GraysHarbor.pdf. Accessed 15 Aug 2010 11. Joint publication: Practical Water Management in Paper and Board Mills. Produced by the Environmental Technology Best Practice Programme, Copyright Crown, UK (1998).
Increase of paper machine efficiency by using a compact wet end system
  • P O Meinander
  • PO Meinander
Meinander PO (2003) Increase of paper machine efficiency by using a compact wet end system. Wochenbl Papierfabr 131(19):1137-1145
  • H Paulapuro
Paulapuro H (2000) Papermaking science and technology, vol 11. Fapet Oy, Helsinki
The state of the paper industry: monitoring the indicators of environmental performance
  • J Roberts
Roberts J (ed.) (2007) The state of the paper industry: monitoring the indicators of environmental performance. Environmental Paper Network, Asheville