Chapter

A Study on the Actuator Efficiency Behavior of Safety-Related Motor Operated Gate and Globe Valves

Authors:
To read the full-text of this research, you can request a copy directly from the authors.

Abstract

Periodically, the operability of the safety-related motor-operated valves (MOVs) in nuclear power plants must be verified. Because the actuator efficiency is one of the most important factors in the determination of the actuator output, it should be considered in ensuring the operability of MOVs during the verification duration. In particular, special consideration should be paid to its potential degradation, but the design efficiency provided by manufacturers is usually used because the actuator efficiency calculation is difficult and requires considerable time and effort. In this paper, a method is introduced to calculate actuator efficiency by using diagnostic signals acquired in field tests. The actuator efficiency was calculated from the estimated motor torque, the stem thrust measured in field tests, and overall gear ratio provided by manufactures. The motor torque was estimated by using an algorithm, which can calculate electric torque from the three phases of currents and voltages, resistances between phases acquired in field tests. The validation of the design efficiencies was evaluated by comparing those efficiencies with the calculated actuator efficiencies. And, the age-related degradation was analyzed through the behavior analysis over time of the calculated actuator efficiencies. Most of the actuator efficiencies were found not to be degraded over time and kept efficiency greater than the design efficiency. However, two actuator efficiencies with lower motor speed, overall gear ratio, and maximum motor torque rating are susceptible to be lower than the design efficiencies. For the two actuators, threshold efficiencies were calculated and provided to replace their design efficiencies.

No full-text available

Request Full-text Paper PDF

To read the full-text of this research,
you can request a copy directly from the authors.

Article
This paper describes how to calculate the stem friction coefficient of safety related motor operated valves (MOVs) that reflects potential degradation with time by using diagnostic signals acquired in static field tests that have been conducted more than two times per valve. Based on the calculated stem friction coefficients, their behaviors with time were analyzed considering various parameters that could cause potential degradation. Most friction coefficients change randomly rather than increasing or decreasing continuously over time. From those trends, a threshold coefficient, which represents the highest expected value of the friction coefficient, was calculated and provided.
Article
Full-text available
This article deals with a new motor-operated valves (MOVs) condition monitoring method. MOVs mainly consist of an induction machine driving a valve through a mechanical actuator. Such systems need important maintenance policies since they are critical concerning the operational readiness of the safety related systems of nuclear power plants. Unfortunately, today's policies present a major drawback. Indeed, these monitoring techniques rely on the measurement of an internal mechanical quantity and require the presence of human operators in dangerous power plants areas. The aim of this research work is to develop a monitoring method relying exclusively on remote electrical measurements (MOV supply voltages and currents), without the need of any internal MOV quantity. In this article, the instantaneous active power absorbed by the induction machine is first shown to be an interesting electrical quantity to elaborate mechanical failure indicators. An efficient real-time algorithm developed to estimate this physical quantity is then detailed and mechanical failure indicators based on the estimated electrical power are proposed. Finally, their performance is illustrated through experimental data.
Article
It is necessary to monitor periodically the operability of safety-related motor-operated valves (MOVs) in nuclear power plants. However, acquiring diagnostic signals for MOVs is very difficult, and doing so requires an excessive amount of time, effort, and expenditure. This paper introduces an accurate and economical method to evaluate the performance of MOVs remotely. The technique to be utilized includes electrical measurements and signal processing to estimate the motor torque and the stem thrust, which have been cited as the two most effective parameters in diagnosing MOVs by the US Nuclear Regulatory Commission. The motor torque is calculated by using electrical signals, which can be measured in the motor control center (MCC). Some advantages of using the motor torque signature over other signatures are examined. The stem thrust is calculated considering the characteristics of the MOV and the estimated motor torque. The basic principle of estimating stem thrust is explained. The developed method is implemented in diagnostic equipment, namely, the Motor Operated Valve Intelligent Diagnostic System (MOVIDS), which is used to obtain the accuracy of and to validate the applicability of the developed method in nuclear power plants. Finally, the accuracy of the developed method is presented and some examples applied to field data are discussed.
Joint Owners' Group (JOG) Motor Operated Valve Periodic Verification Program Summary
JOG, (2004). Joint Owners' Group (JOG) Motor Operated Valve Periodic Verification Program Summary, pp. E1-E2, USA.
Safety Related Motor Operated Valve Testing and Surveillance Generic Letter Periodic Verification of Design-Basis Capability of Safety-Related Motor-Operated Valves Motor Control Center (MCC) Based Technology Study for Safety-Related Motor Operated Valves
  • Generic Letter
USNRC, Generic Letter 89-10 (1989). Safety Related Motor Operated Valve Testing and Surveillance, USA USNRC, Generic Letter 96-05 (1996). Periodic Verification of Design-Basis Capability of Safety-Related Motor-Operated Valves, USA S.C. Kang, S.K. Park, D.H. Lee, Y.S. Kim (2006). Motor Control Center (MCC) Based Technology Study for Safety-Related Motor Operated Valves, Nuclear Engineering and Technology, Vol. 38, No. 2, 155-162.