What’s the best method to achieve invarient face detection For different aged faces?

Hi, I have been trying various protocols from different research papers, but unable to sterilize the saffron corms. Kindly help me with the sterilization protocol.

Protocol followed:

Treat with 0.6% Bavistin for 30min

Rinse and treat with 10% sodium hypochlorite for 20min

Rinse and quick dip in 70% Ethanol for 45sec

Facing 100% contamination of saffron corms, mostly fungal contaminations

Owning to globalization and rapid technological change over the past decades, the major issue in management is the need for efficient leaders or managers . Many companies face difficulties making them fall due to the dynamic changes in this COVID-19 times and this makes them perish or change .

while establishing the causality link between HR and Organization performance. organization performance can in terms of financial, employee outcome and organizational performance outcome indices statistics but the real problem which i am also facing is to measure HR through HR Audit, PCMM, BSC and effectiveness(which is difficult to measure in not so IT savy organizations).

if you can help, as i am also facing same challenge in health care Industry in India.

Regards

I'm modelling a 3D, transient, 2-way FSI problem about deformation of a thin beam, with fixed support from one end and fully submerged in fluid. I need to apply force (or pressure) from one side of the beam to deform it however I wish to apply this force in the Fluent (not in the transient structural module) since the applied force is dependent to flow variables.

I tried to change the pressure on the surface using a simple udf as below:

#include "udf.h"

DEFINE_ADJUST(adjust_function,domain)

{

int surface_thread_id=27;

real press=5000.0;

face_t face;

Thread* thread;

thread = Lookup_Thread(domain,surface_thread_id);

begin_f_loop(face,thread)

{

F_P(face,thread)=press;

}

end_f_loop(face,thread)

}

There were no error at compiling, hooking udf or at running the simulation steps however pressure report or monitors showed no change in pressure on applied surface.

I would appreciate if anyone can help me on this issue.

Kind regards

Hello everyone! I am a mechanical engineering student and am currently doing a project related to the FEA analyses of padeyes and wanted some help. So basically I am trying to apply a force on the top section of the pinhole only and I could do this ansys but I am not able to do it in ABAQUS. The body force option dosent work and when I try to apply pressure loading, the forces are all perpendicular to the face but I want to have vertical forces only. The forces that I am applying are simulating the forces of a pin attached to the lug. Could you also tell me if the forces should be vertical only or should they always be perpendicular to the face like the pressure loads.. Really confused here

I have attached pictures aswell for a clear understanding of the problem

thanks in advance!

Aslam-u-Alaikum,

I am facing issue regarding Beam tilting problem in Slotted waveguide antenna array (Narrow face)?

Is there any one working on this project?

Hi everyone,

I am working with Abaqus and I need to create a cell partition with a closed edge contour like the "📷Photo_1.png".

Anyone knows any Abaqus option to do that? I don´t care if I have to use an Abaqus script to do the partition.

The edges from the closed contour are pairwise parallel. One pair is purely straight, and the other edge pair is curved.

I can´t do a simple "Partititon Cell: Extrude/Sweep Edges" tool on the curved edge because of the geometry of my part, it is a deformed part, so the faces are not perfectly planar and I get results like the "📷Photo_2.png" if I do a huge zoom.

One possible solution could be to find out how to make a larger edge than the narrow face, in order to extrude the edge and dont get the same error as "📷Photo_2.png".

Neither can I use the "Use n-sided patch" tool, because Abaqus raises the following error: "📷Photo_3.png". Thats beacause I am using curved edges (I guess). To prove that, I tried to sketch a simple circle (and other sketch like "📷Photo_4.png") on the narrow face, and Abaqus raise the same error...

My proposed solution is to sketch the face contour in order to achieve the cell partition, but I dont Know how to do it.

I have shared you the same CAE file Im using if you want to prove something.

Any help will be appreciated.

Thanks.

Does anyone able to integrate GNS3 with the Solarwind NPM trial version successfully? I have tried several times and facing numerous issues. the latest one is "Stuck in Active Diagnostics". I ave followed the discussion advised, not resolved. Their product support never answer. Please let me know if anyone has done that successfully. The document that i have followed is attached.

Thank you