Environmental Science and Pollution Research

The presence of dyes in water is undesirable due to the toxicological impact of their entrance into the food chain. Owing to the recalcitrant nature of dyes to biological oxidation, a tertiary treatment like adsorption is required. In the present study, unsaturated polyester resin (UPR) has been used as a sorbent in the treatment of dye-contaminated water. Different concentrations of Tropaeoline 000 containing water were treated with UPR. The preliminary investigations were carried out by batch adsorption to examine the effects of pH, adsorbate concentration, adsorbent dosage, contact time, and temperature. A plausible mechanism for the ongoing adsorption process and thermodynamic parameters have also been obtained from Langmuir and Freundlich adsorption isotherm models. Thermodynamic parameter showed that the sorption process of Tropaeoline 000 onto activated carbon (AC) and UPR were feasible, spontaneous, and endothermic under studied conditions. The estimated values for (ΔG) are -10.48 × 10(3) and -6.098 × 10(3) kJ mol(-1) over AC and UPR at 303 K (30 °C), indicating towards a spontaneous process. The adsorption process followed pseudo-first-order model. The mass transfer property of the sorption process was studied using Lagergren pseudo-first-order kinetic models. The values of % removal and k (ad) for dye systems were calculated at different temperatures (303-323 K). The mechanism of the adsorption process was determined from the intraparticle diffusion model.

TiO(2) anatase nanoplates and hollow microspheres were fabricated by a solvothermal-hydrothermal method using titanium isopropoxide as a titanium precursor and hydrofluoric acid as a capping agent in order to enhance the formation of the {001} crystal facets of the anatase nanocrystals. These different morphological structures of TiO(2) anatase can be achieved by only changing the solvent, keeping the amount of the precursor and of the capping agent identical during the solvothermal-hydrothermal process. After calcination of the samples, the adsorbed fluoride atoms on the {001} crystal facets of the TiO(2) anatase nanocrystals were completely removed from their surface according to XPS analysis. The calcined TiO(2) anatase structures were higher crystallized and the specific surface area of the catalysts increased, enhancing their photocatalytic activity in comparison to the non-calcined TiO(2) anatase structures. All TiO(2) anatase samples with adsorbed as well as non-adsorbed fluoride atoms on their {001} crystal facets, exhibited a higher photonic efficiency than Degussa P25, which was used as a reference. The fluoride free TiO(2) anatase nanoplates exhibited the best photocatalytic activity in oxidizing the NO gas to NO(2) and NO(3) (-).

This paper is in response to criticism of our article "The human sex odds at birth after the atmospheric atomic bomb tests, after Chernobyl, and in the vicinity of nuclear facilities" published in Environ Sci Pollut Res 18(5):697-707, 2011. Our findings and methods concerning the disturbed human sex odds at birth have been criticized in this journal for being artifacts of data mining, that the concept of statistical significance was misunderstood, and that confounding factors have not been accounted for. Here, we show that this criticism has no basis. We applied well-established statistical methods to large official data sets, and confounding is less important at the level of secular sex odds trends in aggregated annual figures from countries or continents. Moreover, our results are strengthened by recent findings concerning increased infant death sex odds in Germany and increased Down syndrome prevalence at birth across Europe after Chernobyl. Prompted by our studies, an official investigation in Lower Saxony, Germany, by the "Niedersächsisches Landesgesundheitsamt (NLGA)" confirmed our observation of severely escalated sex odds within 40 km distance from the nuclear storage site in Gorleben, Germany.

Bacillus thuringiensis PW-05 was isolated from the Odisha coast and was found to resist 50 ppm of Hg as HgCl2 as well as higher concentrations of CdCl2, ZnSO4, PbNO3 and Na2HAsO4. Resistance towards several antibiotics, viz amoxycillin, ampicillin, methicillin, azithromycin and cephradine (CV) was also observed. The mer operon possessed by most of the mercury-resistant bacteria was also found in this isolate. Atomic absorption spectroscopy revealed that the isolate can volatilize >90 % of inorganic mercury. It showed biofilm formation in the presence of 50 ppm HgCl2 and can produce exopolysaccharide under same conditions. The isolate was found to volatilize mercury efficiently under a wide range of environmental parameters, i.e. pH (7 to 8), temperature (25 °C to 40 °C) and salinity (5 to 25 ppt). merA gene expression has been confirmed by real-time reverse transcriptase PCR study. Fourier transform infrared study revealed that -SH and -COOH groups play a major role in the process of adaptation to Hg. Hence, this isolate B. thuringiensis PW-05 shows an interesting potential for bioremediation of mercury.

Chiral, atropisomeric 2,2'-dihydroxy-1,1'-binaphthyl has been extensively used to direct asymmetric processes. Its key role in asymmetric catalysis has spurred efforts to synthesize it in the optically pure form, but the reported synthetic routes have a significant environmental impact. In an aqueous peroxydase-cyclodextrin system the oxidative coupling of 2-naphthol took place very rapidly in almost quantitative yield and resulted in an enantiomeric excess. This one-pot synthesis do not require any organic solvents and oxidising metal cations.

Most studies on the treatment of chlorinated contaminants by Fe(0) focus on aqueous system tests. However, few is known about the effectiveness of these tests for degrading chlorinated contaminants such as 1,1,1-trichloroethane (TCA) in soil. In this work, the reductive degradation performance of 1,1,1-TCA by Fe(0) was thoroughly investigated in a soil slurry system. The effects of various factors including acid-washed iron, the initial 1,1,1-TCA concentration, Fe(0) dosage, slurry pH, and common constituents in groundwater and soil such as Cl(-), HCO3 (-), SO4 (2-), and NO3 (-) anions and humic acid (HA) were evaluated. The experimental results showed that 1,1,1-TCA could be effectively degraded in 12 h for an initial Fe(0) dosage of 10 g L(-1) and a soil/water mass ratio of 1:5. The soil slurry experiments showed two-stage degradation kinetics: a slow reaction in the first stage and a fast reductive degradation of 1,1,1-TCA in the second stage. The reductive degradation of 1,1,1-TCA was expedited as the mass concentration of Fe(0) increased. In addition, high pHs adversely affected the degradation of 1,1,1-TCA over a pH range of 5.4-8.0 and the reductive degradation efficiency decreased with increasing slurry pH. The initial 1,1,1-TCA concentration and the presence of Cl(-) and SO4 (2-) anions had negligible effects. HCO3 (-) anions had a accelerative effect on 1,1,1-TCA removal, and both NO3 (-) and HA had inhibitory effects. A Cl(-) mass balance showed that the amount of Cl(-) ions released into the soil slurry system during the 1,1,1-TCA degradation increased with increasing reaction time, suggesting that the main degradation mechanism of 1,1,1-TCA by Fe(0) in a soil slurry system was reductive dechlorination with 1,1-DCA as the main intermediate. In conclusion, this study provides a theoretical basis for the practical application of the remediation of contaminated sites containing chlorinated solvent.

The construction and electrodes characteristics of poly(vinylchloride) (PVC)-based polymeric membrane electrode (PME) and coated graphite electrode (CGE), incorporating 1,3-alternate thiacalix[4]crown as ionophore for estimation of Hg(II) ions, are reported here. The best potential response was observed for PME-1 having membrane composition of: ionophore (6.2 mg), PVC (100.0 mg), 2-nitrophenyl octyl ether (2-NPOE; 200.0 mg), and sodium tetraphenyl borate (NaTPB; 2.0 mg); for CGE-1 with the membrane composition: ionophore (3.5 mg), PVC (40.0 mg), 2-NPOE (80.0 mg), and NaTPB (2.0 mg). The electrodes exhibits Nernstian slope of 29.16 mV/decade with PME-1 and 30.39 mV/decade with CGE-1 for Hg(II) ions over wide concentration range, i.e., 1.0 × 10(-1) to 5.0 × 10(-6) M with PME-1 and 1.0 × 10(-1) to 5.0 × 10(-7) M with CGE-1. Lower detection limits were found to be 9.77 × 10(-6) M for PME-1 and 7.76 × 10(-7) M for CGE-1 with response time varying from 10 to 20 s. Also, these electrodes work within pH range of 2.0-6.0 for PME-1 and 1.5-6.5 for CGE-1. Overall, CGE-1 has been found to be better than PME-1. CGE-1 has been used as indicator electrode for the potentiometric titration of Hg(II) ions with EDTA as well as successfully applied for determination of Hg(II) content in wastewater, insecticide, dental amalgam, and ayurvedic medicines samples with very good performance (0.9974 correlation coefficient in the comparison against volumetric method).

For decades, the explosive RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine) has been used for military and industrial applications. Residues of RDX pollute soils in large areas globally and the persistence and high soil mobility of these residues can lead to leaching into groundwater. Dendroremediation, i.e. the long-term use of trees to clean up polluted soils, is gaining acceptance as a green and sustainable strategy. Although the coniferous tree species Norway spruce and Scots pine cover large areas of military land in Central Europe, the potential of any coniferous tree for dendroremediation of RDX is still unknown. In this study, uptake experiments with a (14)C-labelled RDX solution (30 mg L(-1)) revealed that RDX was predominantly retained in the roots of 6-year-old coniferous trees. Only 23 % (pine) to 34 % (spruce) of RDX equivalents (RDXeq) taken up by the roots were translocated to aboveground tree compartments. This finding contrasts with the high aerial accumulation of RDXeq (up to 95 %) in the mass balances of all other plant species. Belowground retention of RDXeq is relatively stable in fine root fractions, since water leaching from tissue homogenates was less than 5 %. However, remobilisation from milled coarse roots and tree stubs reached up to 53 %. Leaching from homogenised aerial tree material was found to reach 64 % for needles, 58 % for stems and twigs and 40 % for spring sprouts. Leaching of RDX by precipitation increases the risk for undesired re-entry into the soil. However, it also opens the opportunity for microbial mineralisation in the litter layer or in the rhizosphere of coniferous forests and offers a chance for repeated uptake of RDX by the tree roots.

The treatment of 1,4-dioxane solution by electrochemical oxidation on boron-doped diamond was studied using a central composite design and the response surface methodology to investigate the use of SO4 2− and HCO3 − as supporting electrolytes considering the applied electric current, initial chemical oxygen demand (COD) value, and treatment time. Two industrial effluents containing bicarbonate alkalinity, one just carrying 1,4-dioxane (S1), and another one including 1,4-dioxane and 2-methyl-1,3-dioxolane (S2), were treated under optimized conditions and subsequently subjected to biodegradability assays with a Pseudomonas putida culture. Electrooxidation was compared with ozone oxidation (O3) and its combination with hydrogen peroxide (O3/H2O2). Regarding the experimental design, the optimal compromise for maximum COD removal at minimum energy consumption was shown at the maximum tested concentrations of SO4 2− and HCO3 − (41.6 and 32.8 mEq L−1, respectively) and the maximum selected initial COD (750 mg L−1), applying a current density of 11.9 mA cm−2 for 3.8 h. Up to 98 % of the COD was removed in the electrooxidation treatment of S1 effluent using 114 kWh per kg of removed COD and about 91 % of the COD from S2 wastewater applying 49 kWh per kg of removed COD. The optimal biodegradability enhancement was achieved after 1 h of electrooxidation treatment. In comparison with O3 and O3/H2O2 alternatives, electrochemical oxidation achieved the fastest degradation rate per oxidant consumption unit, and it also resulted to be the most economical treatment in terms of energy consumption and price per unit of removed COD.

This research investigated the 1,4-dioxane (1,4-D) degradation efficiency and rate during persulfate oxidation at different temperatures, with and without Fe(2+) addition, also considering the effect of pH and persulfate concentration on the oxidation of 1,4-D. Degradation pathways for 1,4-D have also been proposed based on the decomposition intermediates and by-products. The results indicate that 1,4-D was completely degraded with heat-activated persulfate oxidation within 3-80 h. The kinetics of the 1,4-D degradation process fitted well to a pseudo-first-order reaction model. Temperature was identified as the most important factor influencing the 1,4-D degradation rate during the oxidation process. As the temperature increased from 40 to 60 °C, the degradation rate improved significantly. At 40 °C, the addition of Fe(2+) also increased the 1,4-D degradation rate. Interestingly, at 50 and 60 °C, the 1,4-D degradation rate decreased slightly with the addition of Fe(2+). This reduced degradation rate may be attributed to the rapid conversion of Fe(2+) to Fe(3+) and the production of an Fe(OH)3 precipitate which limited the ultimate oxidizing capability of persulfate with Fe(2+) under higher temperatures. Higher persulfate concentrations led to higher 1,4-D degradation rates, but pH adjustment had no significant effect on the 1,4-D degradation rate. The identification of intermediates and by-products in the aqueous and gas phases showed that acetaldehyde, acetic acid, glycolaldehyde, glycolic acid, carbon dioxide, and hydrogen ion were generated during the persulfate oxidation process. A carbon balance analysis showed that 96 and 93 % of the carbon from the 1,4-D degradation were recovered as by-products with and without Fe(2+) addition, respectively. Overall, persulfate oxidation of 1,4-D is promising as an economical and highly efficient technology for treatment of 1,4-D-contaminated water.

In the nuclear industry 1,4-dioxane is used as a solvent in liquid scintillation technique for measuring low-energy beta-emitters such as ³H or C¹⁴ in aqueous media. Improper disposal of 1,4-dioxane can contaminate the ground and surface waters. Conventional wastewater treatment processes like chemical treatment, air stripping, carbon adsorption, and biological treatment are ineffective for the degradation of 1,4-dioxane. In the present study, the kinetics of degradation of 1,4-dioxane using advanced oxidation processes viz., H₂O₂ alone, Fe(II) + H₂O₂, UV (15 W) + H₂O₂, UV (15 W) + Fe(II) + H₂O₂, US (130 KHz) + Fe(II) + H₂O₂, and sunlight + Fe(II) + H₂O₂ at pH 3.0 was investigated. The optimization of Fe (II) for the processes using Fe (II) + H₂O₂ was carried out. The kinetics of degradation using sunlight + Fe (II) + H₂O₂ was found to be fastest when compared to the other processes. The degradation was found to follow first-order kinetics. Formation of acidic intermediates was suspected from the observed pH changes during the degradation processes.

BACKGROUND, AIMS, AND SCOPE: Currently, elemental chlorine-free (ECF) and totally chlorine-free (TCF) bleaching systems are widely used for pulp production. Low and medium molecular weight lignin break-down products are known to have harmful effects on the environment. According to some recent results, also high molecular weight (HMW) material consisting mainly of lignin and carbohydrates may cause toxic effects to the environment. For these reasons, toxicity and structure studies of HMW materials are of great importance. This investigation is a part of a larger project to obtain more structure information of HMW materials and toxicity of ECF and TCF bleaching effluents. Size-exclusion chromatography (SEC) has been commonly used for the characterization of organic macromolecules such as lignin, but to our knowledge, no reports have appeared dealing with the comparison of SEC of ECF and TCF bleaching liquors. The aim of the present study was to get more information about the molecular weight distribution (MWD) of HMW fractions of waste liquors from ECF and TCF bleaching sequences by SEC. The MWDs of organic materials dissolved during different stages of ECF bleaching (O-D-EOP-D-ED) and TCF bleaching (O-Z-Q-P-Z-Q-P-P) of softwood (Pinus sylvestris) kraft pulp were determined and compared by SEC. All effluent samples from the above bleaching stages were ultrafiltrated using a membrane with a cutoff value of 1,000 Da. SEC was performed on high and also low molecular weight fractions and non-fractionated effluents. In the SEC experiments, a Superdex 75 column was used with 0.1 M NaOH solution as the eluent. Standards used for calibrating the SEC system were albumin, carboanhydrase, cytochrome C, tannic acid, dehydrodiacetovanillone, and vanillin. The chromatograms of liquors from TCF bleaching stages vary more than those from ECF bleaching. Peroxide and chelating stages contained mostly high molecular weight (HMW) matter whereas chlorine dioxide and ozone stages had more low molecular weight compounds. The lignin content in HMW matter was higher than in stages that consisted of low molecular matter. Bleaching effluents contained the highest amounts of HMW material, mainly lignin, in the beginning of the sequences; the amounts decreased towards the end of the bleaching sequence. Determinations of MWD by the SEC method showed that effluents from the TCF sequence contained more HMW material than those from the ECF stage. This might be due to peroxide stages (P) that dissolve HMW lignin effectively. However, the molecular weights of ozone stages (Z) were very low compared to other stages. Chlorine dioxide stages also dissolved mostly low molecular weight lignin. Ultrafiltration of bleaching liquors showed that high molecular weight fraction also included some low molecular weight compounds and vice versa. High polydispersity and high lignin content correlated with the amount of HMW material in ECF and TCF bleaching stages. Our liquor samples were studied by using a UV detector commonly used for lignin preparations; in upcoming investigations, it will be interesting to determine carbohydrates such as hemicelluloses. The results are applicable in papermaking in order to improve commonly used bleaching procedures, to test new potential bleaching systems, and to study chemical behavior of HMW materials in various bleaching liquors. The present results also form a good basis for toxicity measurements of ECF and TCF bleaching effluents and for more comprehensive spectroscopic and chromatographic experiments with samples taken from various bleaching stages. From the behavior of liquors studied, it appears that our other structure investigations by spectroscopic and chromatographic (NMR, Py-GC/MS, etc.) methods mostly correlate well with the present results.

Textile industries release large amount of wastewater to the environment which alters the clarity of water, interfere with light penetration, and pose toxicity to microbes and fish species. In order to remove the dye from wastewater, this study aimed to optimize electro-oxidation process for the degradation of textile dye C.I. Reactive Orange 107 in wastewater using a statistical tool. The wastewater was synthetically prepared and experiments were designed as the function of variables such as pH (X(1)), NaCl concentration (X(2)), and electrolysis time (X(3)). Graphite electrode was used for all experiments and current was fixed at 34.96 mA cm(-2). The response color and chemical oxygen demand (COD) were measured. UV-visible spectra were recorded at different time intervals and the intermediate was analyzed using FTIR spectrum. The relevant quadratic and interaction terms of factors were investigated. The coefficient of determination (R(2)) value of 0.8227 and 0.9265 for color and COD removal, respectively, indicate the adequacy of the model. The variables such as X(2) and X(3) are significant for color and X(3) is significant for COD removal. The electro-oxidation process efficiently removes color and COD from the Reactive Orange 107 contaminated wastewater. The optimum conditions obtained from the statistical analysis at pH 9.4, NaCl concentration of 0.08 M, and electrolysis time of 16.0 min show maximum color and COD removal of 98%, and 90%, respectively. UV-visible spectrum confirms the decoloration and FTIR spectra show the formation of intermediates.

The focus of this article was to explore the translocation of (109)Cd, (57)Co, (65)Zn, (63)Ni, and (134)Cs via xylem and phloem in the newly found hyperaccumulator Solanum nigrum L. Two experiments with the uptake via the roots and transport of (109)Cd, (57)Co, and (65)Zn labeled by roots, and the redistribution of (109)Cd, (65)Zn, (57)Co, (63)Ni, and (134)Cs using flap label in S. nigrum in a hydroponic culture with a standard nutrient solution were conducted. The results showed that (109)Cd added for 24 h to the nutrient medium of young plants was rapidly taken up, transferred to the shoot, and accumulated in the cotyledons and the oldest leaves but was not efficiently redistributed within the shoot afterward leading to a rather low content in the fruits. In contrast, (57)Co was more slowly taken up and released to the shoot, but afterward, this element was redistributed from older leaves to younger leaves and maturing fruits. (65)Zn was rapidly taken up and transferred to the shoot (mainly to the youngest leaves and not to the cotyledons). Afterward, this radionuclide was redistributed within the shoot to the youngest organs and finally accumulated in the maturing fruits. After flap labeling, all five heavy metals tested ((109)Cd, (57)Co, (65)Zn, (63)Ni, (134)Cs) were exported from the labeled leaf and redistributed within the plant. The accumulation in the fruits was most pronounced for (63)Ni and (65)Zn, while a relatively high percentage of (57)Co was finally found in the roots. (134)Cs was roughly in the middle of them. The transport of (109)Cd differed from that previously reported for wheat or lupin and might be important for the potential of S. nigrum to hyperaccumulate cadmium.

Unlabelled: PURPOSE AND AIM: Amido Black 10B is an azo dye with very high toxicity. It is now established that the dye damages the reparatory system of humans and also causes skin and eye irritations. It is therefore considered worthwhile to develop a systematic procedure to eradicate Amido Black 10B from its aqueous solution using a waste material as adsorbent. Therefore, adsorption of the dye is achieved using hen feathers as adsorbent. Materials and methods: Before using hen feather as adsorbent material, it is washed, cut into small pieces and activated using hydrogen peroxide. Detailed chemical and physical analysis of hen feather was also carried out by known analytical techniques. The adsorptive removal of the dye was made through batch experiments in 100 mL airtight flasks. The experiment is divided in three major categories, the preliminary investigations, adsorption isotherm measurements, and kinetic studies. Results: Under preliminary investigations, the effect of pH, temperature, concentration of dye, and amount of adsorbent were carried out. It was found that with increase in pH, the adsorption of Amido Black 10B decreases; while with increasing the amount of hen feather, it increases. The isothermal studies indicate that the ongoing adsorption process is endothermic in nature and obeys Langmuir, Freundlich, Tempkin, and Dubinin-Radushkevitch (D-R) adsorption isotherm models. The Gibb's free energy and entropy of the adsorption were also calculated. The D-R isotherm model verified the involvement of chemisorption during the adsorption. The kinetic measurements indicate operation of pseudo second order process during the adsorption and dominance of film diffusion mechanism at all the temperatures. Conclusions: The developed method is highly efficient and ecofriendly. It also ascertains a necessitous utilization of waste material hen feather for the benefit of the society.

This paper is a companion to the recent review paper by Laturnus et al. (2005) on TCA in soils, presenting a complementary review of knowledge gaps in the sources and fate of trichloroacetic acid (TCA) in plants. The review considers the various sources of TCA precursors, including the question of how much atmospheric TCA comes from naturally-produced precursors, and addresses the implications of climate change on atmospheric TCA formation. Models of the conversion of precursors to TCA in the atmosphere are critically compared with field measurements of concentrations, deposition and budgets; data on the quantitative relationships between gas-phase TCA, particulate TCA, and TCA dissolved in rain and clouds are reviewed. Methods for quantifying TCA are summarised, along with a description of what the different techniques measure, and how results can be compared. A distinction is made between 'extractable' TCA and 'total' TCA in vegetation. Evidence for the various pathways by which TCA enters plants is given, including the in situ production of TCA in leaves. This leads to a better understanding of how plant tissue concentrations depend on uptake, production and removal rates. Finally, knowledge of the toxic effects of TCA on plants and TCA metabolism in plant tissues is summarised. The discussion highlights knowledge gaps, and is intended to aid the reader in interpreting previously published results through identifying where different ways of expressing data have been used, and the consequent conclusions that can be drawn. CONCLUSION AND FURTHER RESEARCH DIRECTIONS: Recommendations are given for future research directions--in identifying precursor sources, quantifying heterogeneous atmospheric processes, recognising and quantifying uptake pathways, and elucidating the biochemical mechanisms involved in sequestering and degrading TCA inside leaves.

Trichlorofluoromethane, in concentrations of 80, 400, 2 000, 10 000 and 50 000 ppm, was administered to rats of both sexes (Sprague Dawley) by inhalation exposure. 2 000 ppm in air (= 11 200 mg/m3) amount to twice the MAK value of 1 000 ppm. At exposure times of 4 hours this corresponds to the MAK value defined for an 8 hour workday. Unscheduled DNA synthesis (UDS) was measured in single-cell suspensions of hepatocytes, pulmonary epithelial cells and lymphocytes of the spleen, respectively. In the pulmonary cells concentrations of 2 000, 10 000 and 50 000 ppm of freon 11 lead to a significantly increased mean silver grain count compared to a negative control group. In spleen and liver cells increasing concentrations of R 11 tend to increase the incorporation of thymidine into the DNA of the cells. These changes of the extent of unscheduled DNA synthesis can, however, not be statistically verified.

Since the 1970s, at least 200 hectares (ha) of farm-land has been polluted by the heavy metal cadmium (Cd). Consequently, the Cd pollution has led to contaminate the rice production and caused acute social panic. According to the recent investigation results performed by the Taiwan Environmental Protection Administration (TEPA), it is indicated that most of the Cd pollution incidents in Taiwan resulted from the waste-water discharge of stearate Cd factories. To prevent the Cd pollution incidents from spreading, the TEPA has either forced these factories to close down or assisted them in improving their production processes since the 1980s. Unfortunately, accidental incidents of Cd pollution still emerge in an endless stream, despite the strict governmental controls placed on these questionable factories. Whether this pollution has resulted from undetected or hidden pollution sources stemming from two decades ago or comes from some new source, will be an outstanding issue. Therefore, this study attempts to identify the pollution sources of Cd in soil in Taiwan as well as to find the solution to the above-mentioned, outstanding issue by way of a methodology termed Material Flow Analysis (MFA). The MFA has proved to be a useful tool on providing quantitative information of the flow of substances through an economic to an environmental system. Based upon the supply-and-demand theory of MFA, researchers have successfully conducted an overview of the use of materials in many industries, the construction industry being one of these. Therefore, this study tries to establish a set of analytical processes by way of MFA for identifying the pollution source of Cd in soil in Taiwan. In addition, the spirit of Life Cycle Assessment (LCA) technique was also employed to identify the materials, and products should be ignored as a crucial pollution source in this study. According to the MFA methodology applied in this study and on the basis of related studies performed by Taiwanese governmental authorities, we arrive at the following analysis results: (1) the total amount of Cd from the economic perspective of material and product flow was approximately 441.2 tons; (2) the wastewater directly discharged into irrigation water can be concluded to be the major pollution route of Cd in farmland soil in Taiwan; (3) material plastic stabilizer (cadmium oxide, CdO), Zn-Pd compounds and Cu compounds should be the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis; (4) the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis were five factories, Coin, Jili, Taiwan Dye, Guangzheng and Mingguan, and they were all categorized as stearate Cd industries; (5) the typical source of the Cd pollution in soil in Changhua County through the pollution route of wastewater should be the metal surfacing process industries. This study proved that MFA can be a good tool for identifying Cd flow as well as for recognizing the crux of the problem concerning incidents of Cd pollution. This study led to the conclusion that the causal relationship between farmland pollution caused by Cd and stearate Cd factories in Taiwan seemed quite close by way of MFA methodology. In addition, this study also found that the wastewater discharged from a single metal surfacing process factory will not cause remarkable farmland pollution. However, the wastewater simultaneously discharged from a group of pollution factories can result in a significant pollution incident. This case study is only a small contribution to the understanding of the toxic material flow related to Cd in the environment. This study recommends that Taiwanese governmental authorities should not deal with problems on an ad hoc basis, but should instead deal with Cd pollution problems overall employing control measures. Finally, the more accurate information or data we can collect, the more reliable results we can identify. Therefore, the quality and quantity of related data used in this MFA model should be closely scrutinized in order to ensure the most correct and comprehensive investigation on the toxic material flow.

GOALS, SCOPE AND BACKGROUND: Among other substances, sulphur dioxide (SO2), nitric oxide (NO) and nitrogen dioxide (NO2) are parameters which are routinely measured to describe basic air quality. Organic extracts of airborne particulate matter contain mutagenic chemical compounds of different origins. The aim of the study was to find correlations between routine monitoring data and mutagenic activity of organic extracts of simultaneously drawn samples. Specimens were collected over a period of two years at 8 sampling sites in south-west Germany. Simultaneously, concentrations of NO, NO2, and SO2 were measured on-line within the framework of the official air monitoring network of Baden-Württemberg, Germany. Dust samples were collected for biotesting using high volume air samplers equipped with glass fibre filters. After sampling was completed, filters were extracted and samples were prepared for biological testing. Mutagenic activity was tested by means of the plate incorporation assay (Ames test) using S. typhimurium TA98 and TA100 tester strains. During the first year of the study, all tests have been performed with and without metabolic activation. Additionally, a series of tests has been performed in parallel with TA98 and TA98NR. Comparison of Ames test data obtained with and without metabolic activation indicates no statistically significant difference between both methods. Therefore, during the second year of the study, all tests have been performed without metabolic activation. Average yearly activities at the sampling sites were between 1 and 27 Revertants per m3 (Rev/m3). High activities were preferably found at congested sites (Karlsruhe, up to 95 Rev/m3). However, peak values of over 100 Rev/m3 were found in other places where pollution by traffic is significantly lower. The reason for these high level values is not evident. Tests performed using TA98NR tester strain indicate a significant share (average 31%) of compounds requiring activation by nitroreductase for mutagenic activity. Average mutagenic activity can be correlated to routine monitoring parameters. Comparison of averaged data for particular sampling sites indicates significant correlation between nitric oxide and mutagenic activity in TA98 (r2=0.90), while correlation between nitrogen dioxide (0.84) or sulphur dioxide (0.52) and mutagenic activity is weaker. For TA100, correlations are generally weaker than for TA98. Comparison of data for mutagenic activity and routine monitoring data of distant sites being sampled simultaneously shows parallel behaviour. Results from this study show that mutagenic activity can be compared to seasonal and local variations of gaseous indicator air pollutants. Tester strain TA98 generally shows the best correlations. Although pollution by particle-bound mutagenic substances is significantly higher during the cold season than during summer on average, mutagenic activity of airborne dust is not a continuous effect. During winter, peak levels as well as low pollution periods can occur. Even during winter time mutagenic activity can reach very low levels typical for summertime. Comparison of results for distant sampling sites where samples have been collected simultaneously indicate that 'classical' indicators of air pollution and bacterial mutagenicity of organic extracts from airborne particulate matter are influenced by connected effects. Seasonal trend of mutagenic activity, in particular, is similar to the concentrations of nitrogen oxide. NO is a strong indicator for vehicle exhaust gases. It is concluded that the average mutagenic activity at particular sites can be estimated using NO concentrations as an indicator.

Chronic exposure to arsenic (As) in rice has raised many health and environmental problems. As reported, great variation exists among different rice genotypes in As uptake, translocation, and accumulation. Under hydroponic culture, we find that the Chinese wild rice (Oryza rufipogon; acc. 104624) takes up the most arsenic among tested genotypes. Of the cultivated rice, the indica cv. 93-11 has the lowest arsenic translocation factor value but accumulates the maximum concentration of arsenic followed by Nipponbare, Minghui 86, and Zhonghua 11. Higher level of arsenite concentration (50 μM) can induce extensive photosynthesis and root growth inhibition, and cause severe oxidative stress. Interestingly, external silicate (Si) supplementation has significantly increased the net photosynthetic rate, and promoted root elongation, as well as strongly ameliorated the oxidative stress by increasing the activities of antioxidant enzymes superoxide dismutase, ascorbate peroxidase, and peroxidase in roots and/or leaves of 93-11 seedlings. Notably, 1.873 mM concentration of Si considerably decreases the total As uptake and As content in roots, but significantly increases the As translocation from roots to shoots. In contrast, Si supplementation with 1.0 mM concentration significantly increases the total As uptake and As concentrations in roots and shoots of 93-11 seedlings after 50 μM arsenite treatment for 6 days.

The aim of the present work was to study the response of two sunflower genotypes (cultivated sunflower Helianthus annuus cv. 1114 and newly developed genotype H. annuus × Helianthus argophyllus) to Pb medium-term stress and the role of exogenously applied EDTA in alleviating Pb toxicity in hydroponics. Plant growth, morpho-anatomical characteristics of the leaf tissues, electrolyte leakage, total antioxidant activity, free radical scavenging capacity, total flavonoid content, and superoxide dismutase isoenzyme profile were studied by conventional methods. Differential responses of both genotypes to Pb supplied in the nutrient solution were recorded. Pb treatment induced a decrease in the relative growth rate, disturbance of plasma membrane integrity, and changes in the morpho-anatomical characteristics of the leaf tissues and in the antioxidant capacity, which were more pronounced in the cultivated sunflower H. annuus cv. 1114. The new genotype demonstrated higher tolerance to Pb when compared with the cultivar. This was mainly due to increased photosynthetically active area, maintenance of plasma membrane integrity, permanently high total antioxidant activity, and free radical scavenging capacity as well as total flavonoid content. The addition of EDTA into the nutrient solution led to limitation of the negative impact of Pb ions on the above parameters in both genotypes. This could be related to the reduced content of Pb in the roots, stems, and leaves, suggesting that the presence of EDTA limited the uptake of Pb. The comparative analysis of the responses to Pb treatment showed that the deleterious effect of Pb was more pronounced in the cultivated sunflower H. annuus cv. 1114. The new genotype H. annuus × H. argophyllus was more productive and demonstrated higher tolerance to Pb medium-term stress, which could indicate that it may possess certain mechanisms to tolerate high Pb concentrations. This character could be inherited from the wild parent used in the interspecific hybridization. The ability of EDTA to prevent Pb absorption by the plants could underly the mechanism of limiting of the negative impact of Pb ions. Hence, EDTA cannot be used to enhance Pb absorption from nutrient solution by sunflower plants for phytoremediation purposes.

Nafion 117 membrane (N117), an important polymer electrolyte membrane (PEM), has been widely applied in numerous chemical technologies. Its increasing production and utilization will inevitably lead to the problem of waste disposal, with incineration as an important method. However, toxicity data of its combustion products on aquatic organisms have been seldom reported. The present study was therefore conducted to investigate the antioxidant response and Na+, K+-ATPase activity in liver of Carassius auratus exposed to different combustion products of N117 for 5, 15, and 30 days. The concentrations of fluorine ion (F−) in the aquaria among the exposure durations were analyzed using the ion chromatography system. The results showed that these treatments have the capability to induce oxidative stress and suppress Na+, K+-ATPase activity, as indicated by some significant alterations on these measured toxicity end-points in fish liver. According to the integrated biomarker response (IBR) index, the toxicity intensity of these experimental treatments was tentatively ranked. Taken together, these observations provided some preliminary data on the potential toxicity of the combustion products of N117 on aquatic organisms and could fill the information gaps in the toxicity database of the current-use PEM. Graphical Abstract The research technical route for the risk assessments of Nafion membrane on fish

Environmental pollutants polychlorinated biphenyls (PCBs), especially dioxin-like PCBs, cause oxidative stress and associated toxic effects, including cancer and possibly atherosclerosis. We previously reported that PCB 126, the most potent dioxin-like PCB congener, not only decreases antioxidants such as hepatic selenium (Se), Se-dependent glutathione peroxidase, and glutathione (GSH) but also increases levels of the antiatherosclerosis enzyme paraoxonase 1 (PON1) in liver and serum. To probe the interconnection of these three antioxidant systems, Se, GSH, and PON1, we examined the influence of varying levels of dietary Se and N-acetylcysteine (NAC), a scavenger of reactive oxygen species (ROS) and precursor for GSH synthesis, on PON1 in the absence and presence of PCB 126 exposure. Male Sprague-Dawley rats, fed diets with differing Se levels (0.02, 0.2, or 2 ppm) or NAC (1 %), were treated with a single intraperitoneal injection of corn oil or various doses of PCB 126 and euthanized 2 weeks later. PCB 126 significantly increased liver PON1 mRNA, protein level and activity, and serum PON1 activity in all dietary groups but did not consistently increase thiobarbituric acid levels (thiobarbituric acid reactive substances, TBARS), an indicator of lipid oxidation and oxidative stress, in liver or serum. Inadequate (high or low) dietary Se decreased baseline and PCB 126-induced aryl hydrocarbon receptor (AhR) expression but further increased PCB 126-induced cytochrome P450 1A1 (CYP1A1) expression, the enzyme believed to be the cause for PCB 126-induced oxidative stress. In addition, a significant inverse relationship was observed not only between dietary Se levels and PON1 mRNA and PON1 activity but also with TBARS levels in the liver, suggesting significant antioxidant protection from dietary Se. NAC lowered serum baseline TBARS levels in controls and increased serum PON1 activity but lowered liver PON1 activities in animals treated with 1 μmol/kg PCB 126, suggesting antioxidant activity by NAC primarily in serum. These results also show an unexpected predominantly inverse relationship between Se or NAC and PON1 during control and PCB 126 exposure conditions. These interactions should be further explored in the development of dietary protection regimens.

Chlordecone is an organochlorine insecticide that has been widely used to control banana weevil in the French West Indies. As a result of this intense use, up to 20,000 ha are contaminated by this insecticide in the French West Indies, and this causes environmental damage and health problems. A scenario of exposure was drawn by French authorities, based on land usage records. Many efforts have been made to monitor the occurrence of chlordecone and its main metabolites using different analytical methods, including GC, GC/MS, LC/MS, and NIRS. Although these different methods allow for the detection and quantification of chlordecone from soils, none of them estimate the bottleneck caused by extraction of this organochlorine from soils with high adsorption ability. In this study, we used (13)C10-chlordecone as a tracer to estimate chlordecone extraction yield and to quantify chlordecone in soil extracts based on the (13)C/(12)C isotope dilution. We report the optimization of (13)C10-chlordecone extraction from an Andosol. The method was found to be linear from 0.118 to 43 mg kg(-1) in the Andosol, with an instrumental detection limit estimated at 8.84 μg kg(-1). This method showed that chlordecone ranged from 35.4 down to 0.18 mg kg(-1) in Andosol, Nitisol, Ferralsol, and Fluvisol soil types. Traces of the metabolite β-monohydrochlordecone were detected in the Andosol, Nitisol, and Ferralsol soil samples. This last result indicates that this method could be useful to monitor the fate of chlordecone in soils of the French West Indies.

Formaldehyde and acetaldehyde are emitted by many mobile and stationary sources and secondary aldehydes are intermediates in the photo-oxidation of organic compounds in the atmosphere. These aldehydes are emitted indoors by many materials such as furniture, carpets, heating and cooling systems, an by smoking. Carbonyls, mainly formaldehyde and acetaldehyde, have been studied because of their adverse health effects. In addition, formaldehyde is a suspected carcinogen. Therefore, the concentrations of formaldehyde and acetaldehyde were determined to assess the inhalation exposure doses to carbonyls for people who work in a 13-story building and in order to evaluate the cancer hazard. Carbonyl compounds in indoor and outdoor air were measured at a 13-story building located in Mexico City. The mezzanine, fifth and tenth floors, and the third level-parking garage were selected for sampling. Samples were collected in two sampling periods, the first from April 20 to 29, 1998 and the second from December 1 to 20, 1998. Carbonyls were sampled by means of DNHP-coated cartridges at a flow rate of 1 l min(-1) from 9:00 to 19:00 hours, during 2-hour time intervals and analyzed by HPLC with hours, during 2-hour time intervals and analyzed by HPLC with UV/VIS detection. Mean carbonyl concentrations were highest in the 3rd level-parking garage, with the formaldehyde concentration being the highest ranging from 108 to 418 microg m(-3). In working areas, the highest carbonyl arithmetic mean concentrations (AM) were observed on the 5th floor. Acetone and formaldehyde concentrations were highest in April ranging from 161 to 348 microg m(-3) (AM = 226) and from 157 to 270 microg m(-3) (AM = 221), respectively. Propionaldehyde and butyraldehyde were present in smaller concentrations ranging from 2 to 25 and 1 to 28 microg m(-3), respectively, considering all the samples. Mean indoor/outdoor ratios of carbonyls ranged from 1.8 to 9.6. A reduction of inhalation exposure doses of 41% and 45% was observed in the fifth floor air after the air conditioning systems had been repaired. Formaldehyde and acetaldehyde concentrations were higher in smoking environments. Indoor carbonyl concentrations were significantly greater than outdoor concentrations. Tobacco smoke seems to be the main indoor source of formaldehyde. After the air conditioning system was maintained and repaired (as was recommended), an important reduction in the emission of formaldehyde and acetaldehyde was achieved on all floors, except for the 3rd level parking garage, thereby reducing the inhalation exposure doses. The results obtained in this research demonstrated that maintenance of air conditioning systems must be carried out regularly in order to avoid possible adverse effects on health. Additionally, it is mandatory that isolated smoking areas, with air extraction systems, be installed in every public building.

Residues of pesticides in fish farming productions from barrage ponds are seldom studied in spite of increasing health questionings and environmental concerns. The purpose of this study is to establish the pesticide contamination profiles of sediments and edible fish from five ponds in Northeastern France. Multi-residues method and liquid chromatography-tandem mass spectrometry analysis were used to quantify 13 pesticides (azoxystrobin, carbendazim, clomazone, diflufenican, dimethachlor, fluroxypyr, iprodion, isoproturon, mesosulfuron-methyl, metazachlor, napropamid, quizalofop and thifensulfuron-methyl). Ten sediments and 143 muscles samples were analysed, corresponding to two successive fishing campaigns (first fishing date and second fishing date (P2), about 1 year later) on five sites (noted C-0, C-25, C-45, C-75 and C-85 to express the increasing gradient of crop area). Isoproturon was present in all sediments samples (1.8-56.4 μg/kg dry weight). During P2 period, carbendazim was quantified in the fish of site C-0 (0.09 ± 0.02, 0.2 ± 0.1 and 0.17 ± 0.06 μg/kg wet weight (ww) for roach, carp and perch, respectively). Metazachlor was only quantified in perch of the site C-25 (0.13 ± 0.02 μg/kg ww). Concentrations of isoproturon were similar for the sites C-45 and C-75 with 0.4 ± 0.1 and 0.75 ± 0.06 μg/kg ww for carp and perch, respectively. Contamination of fish reflected generally concentrations in surroundings. Isoproturon was the most concentrated and its main source was water for perch while carp was exposed through both water and sediments, highlighting their life strategies in pond.

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g(-1)at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.

In the tradition of the study of materials flows through society, the Substance Flow Analysis (SFA) method is presented. SFA aims at providing the relevant information for a country's overall management strategy regarding single substances or coherent groups of substances. This article is dedicated to the presentation of a threestep general framework for SFA-type studies, and elaborates on its first step the systems definition. Attention is given to the definition of the external and internal system boundaries, the categorization of the system's elements, aspects of materials choice, time, and space, and how these depend on the aim of the conducted study. Moreover, a broader discussion is started on the need for standardization of materials flow studies in general.In the tradition of the study of materials flows through society, the Substance Flow Analysis (SFA) method and its software tool SFINX are presented. SFA aims at providing the relevant information for a country's overall management strategy regarding single substances or coherent groups of substances. Three modelling techniques and their possibilities and limitations are discussed: Bookkeeping, static modelling, and dynamic modelling. The computer program SFINX can be used for varoius purposes: (1) to obtain an overview of stocks and flows of a substance in, out and through a nation's economy and environment for a specific year, (2) to trace the origins of specific pollution problems, and (3) to estimate the effectiveness of certain abatement measures. Each application has its own requirements with regard to data and modelling.

The purpose of this paper is to determine the activity concentrations of radionuclide (137)Cs in soil samples on the territory of Belgrade and the province of Vojvodina. Also, the lifetime cancer mortality risk from external exposure during 1 year is assessed, and the effective dose is estimated. Eighty eight soil samples were collected from 30 uncultivated locations in Belgrade, and 30 soil samples were collected from 10 locations in the province of Vojvodina. Activity concentrations were measured using an HPGe detector. Using dose conversion factors taken from "EPA Federal Guidance Report 12," annual effective doses from external sources were estimated. The lifetime cancer mortality risk was assessed using cancer risk coefficients taken from "EPA Federal Guidance Report 13." Activity concentrations of (137)Cs for the territory of Belgrade are in the range of 2.07-89.1 Bq/kg with a mean value of 23.77 Bq/kg; the estimated annual effective doses are in the range of 0.41-17.5 nSv with a mean value of 4.67 nSv, and assessed lifetime cancer mortality risks, normalized on 100,000 inhabitants, are in the range 0.2-9.5 × 10(-5) with a mean value 2.5 × 10(-5). Activity concentrations of (137)Cs for the province of Vojvodina are in the range of 2.73-18.9 Bq/kg with a mean value of 8.57 Bq/kg; estimated annual effective doses are in the range of 0.54-3.71 nSv with a mean value of 1.68 nSv, and assessed lifetime cancer mortality risks, normalized on 100,000 inhabitants, are in the range of 0.3-2.0 × 10(-5) with a mean value 0.9 × 10(-5). Receiving doses are low from (137)Cs radionuclides occurring in soil, according to the linear no-threshold approach; the risk for cancer development exists but is very small.

Altamira Cave (north of Spain) contains one of the world's most prominent Paleolithic rock art paintings, which are threatened by a massive microbial colonization of ceiling and walls. Previous studies revealed that exchange rates between the cave and the external atmosphere through the entrance door play a decisive role in the entry and transport of microorganisms (bacteria and fungi) and nutrients to the interior of the cave. A spatial-distributed sampling and measurement of carrier (CO2) and trace (CH4) gases and isotopic signal of CO2 (δ(13)C) inside the cave supports the existence of a second connection (active gas exchange processes) with the external atmosphere at or near the Well Hall, the innermost and deepest area of the cave. A parallel aerobiological study also showed that, in addition to the entrance door, there is another connection with the external atmosphere, which favors the transport and increases microorganism concentrations in the Well Hall. This double approach provides a more complete knowledge on cave ventilation and revealed the existence of unknown passageways in the cave, a fact that should be taken into account in future cave management.

Biodesulfurization (BDS) has the potential to desulfurize dibenzothiophene (DBT) and its alkylated derivatives, the compounds that are otherwise refractory to hydrodesulfurization (HDS). Thermophilic microorganisms are more appropriate to be used for BDS applications following HDS. The aim of the present study was to isolate a thermophilic microorganism and to explore its commercial relevance for BDS process. The desulfurizing thermophilic strain was isolated and enriched from various soil and water samples using sulfur free medium (SFM) supplemented with DBT. Microbiological and genomic approach was used to characterize the strain. Desulfurization reactions were carried out using DBT and petroleum oils at 45°C followed by different analytical procedures. We report the isolation of a thermophilic bacterium Klebsiella sp. 13T from contaminated soils collected from petroleum refinery. HPLC analysis revealed that Klebsiella sp. 13T could desulfurize DBT to 2-hydroxybiphenyl (2-HBP) at 45°C through 4S pathway. In addition, adapted cells of Klebsiella sp. 13T were found to remove 22-53% of sulfur from different petroleum oils with highest sulfur removal from light crude oil. Klebsiella sp. 13T is a potential candidate for BDS because of its thermophilic nature and capability to desulfurize petroleum oils.

The amount of non-extractable residues (NER) of organic xenobiotics in the soil can considerably exceed the amount of extractable residues which are accessible to normal residue analysis. The NER therefore present a burden to the soil, the toxicological and ecotoxicological potential of which is largely unknown. For the characterization of bound residues and their binding type, special solubilization methods such as supercritical fluid extraction are applied and experiments with radiolabeled model polymers are performed. Mineralization experiments with [(14)C] labeled xenobiotics in natural soil show that a total degradation is still also possible in the environment when in a bound form. Ecotoxicological effects of non-extractable residues may be recorded when their concentration is high, when the parent compound exhibits a high ecotoxicity and the applied detection method is sufficiently sensitive.

The issue of whether food miles are a relevant indicator for the environmental impacts associated with foods has received significant attention in recent years. It is suggested here that issues other than the distance travelled need to be considered. The argument is presented by illustrating the case for the provision of apples. The effects of variability in primary energy requirements for apple cultivation and for other life cycle stages, seasonality (timing of consumption) and loss of produce during storage are studied in this paper, by comparing apples from different supplier countries for consumption in Europe. Data sources for primary energy use (PEU) of apple production are identified ranging from 0.4-3.8 MJ/kg apples for European and Southern American countries and 0.4-0.7 MJ/kg for New Zealand. This variability is related to different yields and producer management practices in the different countries. Storage loss may range from 5% to 40% for storage periods between 4 and 10 months, and this has a significant effect on the results (e.g. increasing the total PEU by 8-16% when stored for 5-9 months in Europe as compared with a no loss and no storage situation). The storage periods and related storage losses change markedly through the year for imported (i.e. non-European) versus European apples. The timing of consumption and related storage losses need to be included in the assessment, as this affects the order of preference for locally sourced versus imported apples. The variability in energy requirements in different life cycle stages, but particularly for the fruit production stage, is also significant in this comparative analysis. Overall, it seems that there are similarities in the total PEU ranges for European and New Zealand apples during the Southern Hemisphere's apple season (European spring and summer). However, during the European autumn and winter (Northern Hemisphere apple season) PEU values are generally higher for apples imported from the Southern Hemisphere compared with European apples consumed in Europe. However, this latter observation may not hold true where apples for consumption in one European country are imported from another European country, because energy use for road transportation has a significant influence on the result. Future studies comparing alternative sources of fresh produce need to account for ranges of data for the fruit production and storage stages, which reflect the seasonality of production.

(14)C-TNT was used to quantify the uptake rate and metabolic turnover of TNT in Phaseolus vulgaris. Seventeen plants were analysed by a special cell fractionation method with polar and nonpolar solvents and enzymes. We obtained three cytoplasmic fractions and five cell wall derived fractions. The recovery rate was 72% as measured by liquid scintillation counting. (14)C partitioned almost in equal amounts with approximately 50% in the cytoplasm and in the cell wall. The majority of the TNT-metabolites are present in the cytoplasm as was shown by GC/ECD and thin layer chromatography. The(14)C in the cell wall is bound probably resulting in long-term immobilisation of these metabolites. We conclude that plants may also be a model for nitroaromatic turnover and immobilisation in soil components.

In order to evaluate the estrogenic activity of sediments and XAD water extracts of selected sites of the catchment area of the River Neckar, a river system in Southern Germany, an integrative assessment approach was used to assess the ecological hazard potential of endocrine-disrupting compounds in sediment and water. The approach is based on estrogen receptor-mediated vitellogenin synthesis induced in isolated hepatocytes of rainbow trout and quantified in a non-radioactive dot blot/RNAse protection-assay in parallel to comprehensive chemical analyses of estrogenic substances. Numerous investigated extracts revealed an estrogen activity comparable to that of the positive control (1 nM 17beta-estradiol corresponding to 270 ng/L in the test medium). Based on a concentration factor of 30 in the extracts and a recovery of XAD resins of approximately 80%, 17beta-estradiol equivalent concentrations between 20 and 26.7 ng/L could be calculated downstream of a sewage treatment plant (< 0.1 ng/L for a reference site). A comparison of the bioassay-derived Bio-TEQs (toxicity equivalents) and the Chem-TEQs revealed a high correlation with a Pearson coefficient of 0.85, indicating that the same ranking of the samples could be obtained with respect to the endocrine disrupting potential with both chemical and bioanalytical analysis. However, the TEQ concentrations computed from chemical analyses were significantly lower than the bioassay-derived TEQ concentrations. In fact, in none of the samples, more than 14% of the vitellogenin-inducing potency could be attributed to the substances (steroids, alkylphenols, bisphenol A, diethylstilbestrol) analyzed. A comparison of the endocrine disrupting potential of sediments extracted by the solvents acetone and methanol revealed lower biological effects for acetone-extracted samples. Possible reasons may be a masking of endocrine effects in acetone extracts by cytotoxicity, a low extraction efficiency of the solvent acetone, or anti- estrogen potencies of some extracted sediment compounds. Using a mass balance approach, the contribution of the compounds analyzed chemically (Chem-TEQs) to the total endocrine activity (Bio-TEQs) was calculated. Based on the very low detection limits, particularly of the steroids with their high TEF factors, results revealed that a calculation of the Chem-TEQs is associated with considerable scale inaccuracy: Whereas only 7-15% of the biological effectiveness (Bio-TEQs) could be explained by endocrine substances identified above the detection limits, the assumption of concentrations slightly below the given detection limits would result in a significant over estimation (137-197%) of the Bio-TEQs. Even the interassay variation of the dot blot assay with different fish donors for primary hepatocyte (factor 2-2.5) is relatively low, when compared to the large range of the Chem-TEQ concentrations (factor 20) obtained when applying different modes of calculation. CONCLUSIONS AND OUTLOOK: Overall, only a minor portion of the endocrine activity detected by bioassays could be linked to compounds identified by chemical analysis. In vitro assays for assessment of endocrine activities are useful as sensitive integrating methods that provide quantitative estimates of the total activity of particular receptor-mediated responses. Although discrepancies may also result from different bioanalytical approaches, it is overall likely that bioanalytical and not chemical analytical approaches give the correct estimate of endocrine disrupting potencies in environmental samples. As a conclusion, assessment of endocrine disruption based on chemical analysis alone does not appear sufficient and further research into the spectrum of substances with potential endocrine activity as well as into additive or even synergistic effects in complex environmental samples is urgently needed.

This paper analyzes the effect of exogenous urea in increased concentration gradient (0, 100, 500 and 1,000 mg L(-1)) on photosynthetic pigments (measured spectrophotometrically), uptake of (14)CO2 (using radioisotope), and urease activity (by measuring ammonia with Nessler's reagent) in leaves of Elodea densa Planch. We have observed that low concentration of urea (100 mg L(-1)) stimulates the accumulation of photosynthetic pigments and intensifies photosynthesis in E. densa, whereas high concentration (1,000 mg L(-1)) suppresses these processes. Urease activity increased by approximately 2.7 and 8 fold when exogenous urea concentrations were 100 and 500 mg L(-1), respectively. However, exogenous urea in high concentration (1,000 mg L(-1)) decreased urease activity by 1.5 fold compared to the control. The necessity of mitigating urea and other nitrogen-containing compounds (NH3 from urea) in water bodies has been discussed with emphasis on the potential for phytoremediation of urea using common water weed viz. E. densa.

The 14th European Association of Chemical and Molecular Sciences (EuCheMS) International Conference on Chemistry and the Environment (ICCE 2013) took place on 25-28 June 2013 at the IEC and the WTC in Barcelona, Spain. The ICCE is a well-established biannual conference organized by the Division of Chemistry and the EuCheMS.

The ubiquitous dissolved organic matter (DOM) has an important influence on transformation of organic contaminants through the production of reactive substances, such as (•)OH, (1)O(2), and (3)DOM*. The photolysis of a higher chlorinated polychlorinated biphenyl (PCB) congener (2,2',4,4',5,5'-hexachlorobiphenyl, PCB 153) under simulated sunlight in presence of humic acid (HA) was investigated. Degradation of PCB 153 was accelerated significantly by the addition of HA, with a rate constant of 0.0214, 0.0413, and 0.0358 h(-1) in the initial 18 h of irradiation in presence of 1, 5, and 20 mg/L HA, respectively. The main photodegradation products analyzed by gas chromatography mass spectrometry were 4-hydroxy-2,2',4',5,5'-pentaCB and 2,4,5-trichlorobenzoic acid. Main reactive species involved were determined by the electron spin-resonance spectroscopy, including (1)O(2) and (•)OH. Special scavengers were added to elucidate the photolysis mechanisms. By using the specific scavengers, it turned out that (•)OH accounted for 29.3 % of the degradation, and the intra-DOM reactive species ((1)O(2), (•)OH, and (3)DOM*) accounted for 59.6 % of the degradation. Photo-transformation sensitized by DOM, which involves both aqueous and intra-DOM reactions of PCBs with reactive species, may be one of the most important mechanisms for natural attenuation of PCBs.