-
[show abstract]
[hide abstract]
ABSTRACT: Porous polymethylmethacrylate (PMMA) has been used as an alloplastic bone substitute in the craniofacial complex, showing integration with the surrounding soft and hard tissue. This study investigated the physicochemical properties of curing and cured mixtures of a PMMA-based bone cement and a carboxymethylcellulose (CMC) gel porogen. Four formulations yielding porous PMMA of varied porosity were examined; specifically, two groups containing 30% (w/w) CMC gel in the mixture using a 7% (w/v) or 9% (w/v) stock CMC gel (30-7 and 30-9, respectively) and two groups containing 40% (w/w) CMC gel (40-7 and 40-9). An additional group comprising solid PMMA without CMC was investigated. The incorporation of the CMC gel into the PMMA bone cement during polymerization decreased the setting time from 608 ± 12 s for the solid PMMA to 427 ± 10 s for the 40-9 group, and decreased the maximum temperature from 81 ± 4°C for the solid PMMA to 38 ± 2°C for the 40-9 group. The porous PMMA groups exhibited reduced compressive strength and bending modulus and strength relative to the solid PMMA. All the porous PMMA formulations released more unconverted methylmethacrylate (MMA) monomer and N,N-dimethyl-p-toluidine (DMT) from cured specimens and less MMA and DMT from curing specimens than the solid PMMA. The data suggest that the physicochemical properties of the porous PMMA formulations are appropriate for their application in craniofacial space maintenance. © 2013 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2013.
Journal of Biomedical Materials Research Part B Applied Biomaterials 01/2013; · 2.15 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: This study investigated the formulation of a two-component biodegradable bone cement comprising the unsaturated linear polyester macromer poly(propylene fumarate) (PPF) and crosslinked PPF microparticles for use in craniofacial bone repair applications. A full factorial design was employed to evaluate the effects of formulation parameters such as particle weight percentage, particle size, and accelerator concentration on the setting and mechanical properties of crosslinked composites. It was found that the addition of crosslinked microparticles to PPF macromer significantly reduced the temperature rise upon crosslinking from 100.3°C ± 21.6°C to 102.7°C ± 49.3°C for formulations without microparticles to 28.0°C ± 2.0°C to 65.3°C ± 17.5°C for formulations with microparticles. The main effects of increasing the particle weight percentage from 25 to 50% were to significantly increase the compressive modulus by 37.7 ± 16.3 MPa, increase the compressive strength by 2.2 ± 0.5 MPa, decrease the maximum temperature by 9.5°C ± 3.7°C, and increase the setting time by 0.7 ± 0.3 min. Additionally, the main effects of increasing the particle size range from 0-150 μm to 150-300 μm were to significantly increase the compressive modulus by 31.2 ± 16.3 MPa and the compressive strength by 1.3 ± 0.5 MPa. However, the particle size range did not have a significant effect on the maximum temperature and setting time. Overall, the composites tested in this study were found to have properties suitable for further consideration in craniofacial bone repair applications.
Journal of Biomedical Materials Research Part A 04/2012; 100(9):2252-9. · 2.63 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Reconstruction of composite defects involving bone and soft tissue presents a significant clinical challenge. In the craniofacial complex, reconstruction of the soft and hard tissues is critical for both functional and aesthetic outcomes. Constructs for space maintenance provide a template for soft tissue regeneration, priming the wound bed for a definitive repair of the bone tissue with greater success. However, materials used clinically for space maintenance are subject to poor soft tissue integration, which can result in wound dehiscence. Porous materials in space maintenance applications have been previously shown to support soft tissue integration and to allow for drug release from the implant to further prepare the wound bed for definitive repair. This study evaluated solid and low porosity (16.9% ± 4.1%) polymethylmethacrylate space maintainers fabricated intraoperatively and implanted in a composite rabbit mandibular defect model for 12 weeks. The data analyses showed no difference in the solid and porous groups both histologically, evaluating the inflammatory response at the interface and within the pores of the implants, and grossly, observing the healing of the soft tissue defect over the implant. These results demonstrate the potential of porous polymethylmethacrylate implants formed in situ for space maintenance in the craniofacial complex, which may have implications in the potential delivery of therapeutic drugs to prime the wound site for a definitive bone repair.
Journal of Biomedical Materials Research Part A 03/2012; 100(4):827-33. · 2.63 Impact Factor
