-
[show abstract]
[hide abstract]
ABSTRACT: Nanocomposites with magnetic components possessing nanometric dimensions, lying in the range 1–10 nm, are found to be exhibiting
superior physical properties with respect to their coarser sized counterparts. Magnetic nanocomposites based on gamma iron
oxide embedded in a polymer matrix have been prepared and characterized. The behaviour of these samples at low temperatures
have been studied using Mössbauer spectroscopy. Mössbauer studies indicate that the composites consist of very fine particles
of γ-Fe2O3 of which some amount exists in the superparamagnetic phase. The cycling of the preparative conditions were found to increase
the amount of γ-Fe2O3 in the matrix.
Bulletin of Materials Science 04/2012; 27(4):361-366. · 0.88 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The effect of frequency, composition and temperature on the a.c. electrical conductivity were studied for the ceramic, Ni1−xZnxFe2O4, as well as the filler (Ni1−xZnxFe2O4) incorporated rubber ferrite composites (RFCs). Ni1−xZnxFe2O4 (where) (bix)varies from 0 to 1 in steps of 0.2 were prepared by usual ceramic techniques. They were then incorporated into a butyl rubber matrix according to a specific
recipe. The a.c. electrical conductivity (σa.c) calculations were carried out by using the data available from dielectric measurements and by employing a simple relationship.
The a.c. conductivity values were found to be of the order of 10−3 S/m. Analysis of the results shows that σa.c. increases with increase of frequency and the change is same for both ceramic Ni1−xZnxFe2O4 and RFCs. σa.c increases initially with the increase of zinc content and then decreases with increase of zinc. Same behaviour is observed
for RFCs too. The dependence of σa.c on the volume fraction of the magnetic filler was also studied and it was found that the a.c. conductivity of RFCs increases
with increase of volume fraction of the magnetic filler. Temperature dependence of conductivity was studied for both ceramic
and rubber ferrite composites. Conductivity shows a linear dependence with temperature in the case of ceramic samples.
Bulletin of Materials Science 04/2012; 25(7):599-607. · 0.88 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Mn1−xZnxFe2O4 nanoparticles (x = 0 to 1) were synthesized by the wet chemical co-precipitation technique. X-ray diffraction and transmission electron microscopy and high resolution transmission electron microscopy were effectively utilized to investigate the different structural parameters. The ac conductivity of nanosized Mn1−xZnxFe2O4 were investigated as a function of frequency, temperature and composition. The frequency dependence of ac conductivity is analysed by the power law σ(ω)ac = Bωn which is typical for charge transport by hopping or tunnelling processes. The temperature dependence of frequency exponent n was investigated to understand the conduction mechanism in different compositions. The conduction mechanisms are mainly based on polaron hopping conduction.
Journal of Physics D Applied Physics 07/2009; 42(16):165005. · 2.54 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The temperature and frequency dependence of dielectric permittivity and dielectric loss of nanosized Mn(1-x)Zn(x)Fe(2)O(4) (for x = 0, 0.2, 0.4, 0.6, 0.8, 1) were investigated. The impact of zinc substitution on the dielectric properties of the mixed ferrite is elucidated. Strong dielectric dispersion and broad relaxation were exhibited by Mn(1-x)Zn(x)Fe(2)O(4). The variation of dielectric relaxation time with temperature suggests the involvement of multiple relaxation processes. Cole-Cole plots were employed as an effective tool for studying the observed phenomenon. The activation energies were calculated from relaxation peaks and Cole-Cole plots and found to be consistent with each other and indicative of a polaron conduction.
Journal of Physics Condensed Matter 04/2009; 21(14):146006. · 2.55 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Fine particles of cobalt ferrite were synthesized by the sol–gel method. Subsequent heat treatment at different temperatures yielded cobalt ferrites having different grain sizes. X-ray diffraction studies were carried out to elucidate the structure of all the samples. Dielectric permittivity and ac conductivity of all the samples were evaluated as a function of frequency, temperature and grain size. The variation of permittivity and ac conductivity with frequency reveals that the dispersion is due to Maxwell–Wagner type interfacial polarization in general, with a noted variation from the expected behaviour for the cold synthesized samples. High permittivity and conductivity for small grains were explained on the basis of the correlated barrier-hopping model.
Journal of Physics D Applied Physics 03/2007; 40(6):1593. · 2.54 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Rubber ferrite composites (RFCs) containing powdered nickel zinc ferrite (Ni1 - xZnxFe2O4 ) in a natural rubber matrix have been prepared and their mechanical and dielectric properties have been evaluated. Variations in the relative permittivity of both the ferrite ceramics and RFCs have been studied over a range of frequencies, ceramic compositions, ceramic filler loadings, and temperatures, and the results have been correlated. Appropriate mixture equations have been formulated to calculate the dielectric permittivity of the composite from the dielectric permittivity of its constituents. Values calculated using these equations have been compared with experimental data on relative permittivity, and the two have been found to be in good agreement. In the present investigation it was also observed that for x = 0 4 and for the maximum ferrite loading, the composite sample exhibits maximum magnetisation and optimum flexibility.
Plastics Rubber and Composites 11/2002; 31(10):449-457. · 0.60 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Rubber ferrite composites have the unique advantage of mouldability, which is not easily obtainable using ceramic magnetic materials. The incorporation of mixed ferrites in appropriate weight ratios into the rubber matrix not only modifies the dielectric properties of the composite but also imparts magnetic properties to it. Mixed ferrites belonging to the series of Mn(1 -x)Znx Fe2 O4 have been synthesised with different values of x in steps of 0·2, using conventional ceramic processing techniques. Rubber ferrite composites were prepared by the incorporation of these pre-characterised polycrystalline Mn(1 -x)ZnxFe2 O4 ceramics into a natural rubber matrix at different loadings according to a specific recipe. The processability of these elastomers was determined by investigating their cure characteristics. The magnetic properties of the ceramic fillers as well as of the rubber ferrite composites were evaluated and the results were correlated. Studies of the magnetic properties of these rubber ferrite composites indicate that the magnetisation increases with loading of the filler without changing the coercive field. The hardness of these composites shows a steady increase with the loading of the magnetic fillers. The evaluation of hardness and magnetic characteristics indicates that composites with optimum magnetisation and almost minimum stiffness can be achieved with a maximum loading of 120 phr of the filler at x=0 4. From the data on the magnetisation of the composites, a simple relationship connecting the magnetisation of the rubber ferrite composite and the filler was formulated. This can be used to synthesise rubber ferrite composites with predetermined magnetic properties.
Plastics Rubber and Composites 02/2002; 31(3):106-113. · 0.60 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Polycrystalline single phasic mixed ferrites belonging to the series Ni1–x
Zn
x
Fe2O4 for various values of
x
have been prepared by conventional ceramic techniques. Pre-characterized nickel zinc ferrites were then incorporated into a natural rubber matrix according to a specific recipe for various loadings. The processability and cure parameters were then determined. The magnetic properties of the ceramic filler as well as the ferrite loaded rubber ferrite composites (RFC) were evaluated and compared. A general equation for predicting the magnetic properties was also formulated. The validity of these equations were then checked and correlated with the experimental data. The coercivity of the RFCs almost resemble that of the ceramic component in the RFC. Percolation threshold is not reached for a maximum loading of 120 phr (parts per hundred rubber by weight) of the filler. These studies indicate that flexible magnets can be made with appropriate magnetic properties namely saturation magnetisation (M
s) and magnetic field strength (H
c) by a judicious choice of x and a corresponding loading. These studies also suggest that there is no possible interaction between the filler and the matrix at least at the macroscopic level. The formulated equation will aid in synthesizing RFCs with predetermined magnetic properties.
Journal of Materials Science 11/2001; 36(23):5551-5557. · 2.02 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Rubber ferrite composites (RFC) are important since they have useful applications as microwave absorbers and flexible magnets. The mouldability of these composites into complex shapes is another advantage. The evaluation of their dielectric and magnetic properties is important in understanding the physical properties of these composites. Pre-characterized nickel zinc ferrites (Ni1-xZnxFe2O4 where 0 x1 in steps of 0.2) prepared by ceramic techniques were incorporated in to a butyl rubber matrix according to a specific recipe to yield RFCs. The dielectric constant of ceramic Ni1-xZnxFe2O4 and the butyl rubber composites incorporated with Ni1-xZnxFe2O4 are studied as a function of frequency, composition, loading and temperature. The observed data indicates that the dependence of the dielectric constant on frequency follows Maxwell-Wagner interfacial polarization. The compositional (zinc content, i.e. x value) dependence shows that the dielectric constant increases initially and reaches a maximum value for the composition corresponding to x = 0.6 and thereafter it decreases. This can be explained on the basis of porosity and alternating current (AC) conductivity. It was also observed that the dielectric constant of the composite material increases with an increase of the volume fraction of the magnetic filler. These observations satisfy some mixture equations, which correlate the dielectric constant of the matrix, filler and the composites. The temperature dependence of the dielectric constant of the ceramic samples as well as the RFCs shows an increase with an increase of temperature at low frequencies. The dielectric constant of the blank butyl rubber was also determined. It was observed that for a blank sample (without filler) the dielectric constant decreases with an increase of temperature. This is due to the decrease in polymer density with increase in temperature. These results suggest that the magnetic and dielectric properties of RFCs can be manipulated by appropriate loading and a judicious choice of the magnetic filler. The modification of these properties will aid in the design of composite materials for microwave absorbers.
Journal of Physics D Applied Physics 07/1999; 32(15):1801. · 2.54 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Spinel ferrites constitute an important class of magnetic materials. Polycrystalline ferrites are a complex system composed of crystallite grain boundaries and pores. Manganese zinc ferrites have resistivities between 0.01 and 10 Ω m. Making composite materials of ferrites with either natural rubber or plastics will modify the electrical properties of ferrites. Composite materials are ideally suited for many modern applications where ceramic materials have some drawbacks. The mouldability and flexibility of these composites find wide use in industrial and other scientific applications. Mixed ferrites belonging to the series Mn(1−x)ZnxFe2O4 (MZF) were synthesized for different ‘x’ values in steps of 0.2. These pre-characterized ceramic ferrites were then incorporated in a natural rubber matrix. The dielectric properties of the ceramic manganese zinc ferrite and RFC were also studied. A program based on G programming was developed with the aid of LabVIEW package to automate the dielectric measurements. The dielectric permittivity of the RFC were then correlated with that of the corresponding dielectric permittivity of the magnetic filler and matrix by a mixture equation, which helps to tailor properties of the composites.
Materials Research Bulletin. 37(4):753-768.
-
[show abstract]
[hide abstract]
ABSTRACT: Composite magnetic materials have the unique advantage of property modification for tailoring devices for various applications. Rubber ferrite composites (RFCs) prepared by incorporating ferrites in rubber matrixes have the advantage of easy mouldability and flexibility. RFCs containing various loadings of nickel zinc ferrite (NZF) (Ni1−xZnxFe2O4) in a natural rubber matrix have been prepared. The cure characteristics and the mechanical properties of these composites were evaluated. The effect of loading on the cure characteristics and tensile properties were also evaluated. It is found that the loading dependence on the cure time and mechanical properties exhibit an identical pattern.
Materials Letters.
