-
[show abstract]
[hide abstract]
ABSTRACT: To evaluate the influence of tooth bleaching on the opalescence properties of enamel.
Color of 38 specimens was determined by colorimetric analysis before and after bleaching in the reflectance and transmittance modes. The results were described as CIELab color coordinates. The Opalescent Parameter (OP) was calculated as the difference in yellow-blue color coordinate (CIE Δb*) and red-green color coordinate (CIE Δa*) between the reflected and transmitted colors.
Mean OP value of the specimens was 18.9 (±1.6) before bleaching and 16.1 (±1.0) after bleaching.
Bleaching decreases the OP of the specimens (p>0.001). OP decrease was correlated with differences in b* color coordinate in the transmittance mode.
Journal of dentistry 02/2012; 40 Suppl 1:e35-9. · 2.00 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: To evaluate whether the use of a desensitizing agent before at-home vital bleaching decreased this sensitivity.
After informed consent, 60 subjects, 18-31 years of age, participated in the study and were divided into desensitizer and placebo groups. Before bleaching treatment with 16% carbamide peroxide (CP), a placebo or desensitizer gel (DG; 5% potassium nitrate and 2% sodium fluoride) was applied in the tray and used by patients for 10 minutes. Color was evaluated at the baseline, second and fourth week following the initial delivery of bleaching trays. Color change was measured using the Vita Classic Shade Guide arranged by value. The subjects recorded their perception of tooth sensitivity on a 0-4 scale. The bleaching treatment at each week recall was evaluated by repeated measures ANOVA. The percentage of patients with tooth sensitivity was evaluated by Chi-square test. The tooth intensity ratio (% of days with tooth sensitivity) as well as the tooth sensitivity intensity between groups were analyzed using chi-square and the Mann-Whitney tests, respectively (alpha = 0.05).
The use of DG did not affect the bleaching efficacy of the CP (P > 0.05). The prevalence and intensity of tooth sensitivity was similar for both groups (P > 0.05). However, participants from the placebo group had sensitivity in 33.6% of the bleaching days, which was significantly higher than the DG experimental group (20.1%) (P < 0.05).
American journal of dentistry 12/2011; 24(6):379-82. · 0.76 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The aim of this in vitro study was to evaluate the microtensile bond strength (µTBS) of a low-shrink silorane-based composite (Filtek Silorane) and a methacrylate-based composite (Filtek Z250) to the bottom dentin of a Class I cavity using different placement techniques. Twelve third molars were used. Standard, box-type Class I cavities (6.0 x 4.0 x 2.5 mm) were prepared at the occlusal crown center, with the pulpal floor ending approximately at the midcoronal dentin. The teeth were then randomly divided into four groups, according to each placement technique: ZI--Filtek Z250 placed incrementally; ZB--Filtek Z250 placed in bulk; SI--Filtek Silorane placed incrementally; and SB--Filtek Silorane placed in bulk. Each restored third molar was subjected to microtensile bond testing after 24 hours of storage in distilled water at 37 degrees C. After storage, each molar was longitudinally sectioned in both axes to obtain rectangular sticks with an approximate 0.49 mm2 cross-sectional area. Data were analyzed by one-way ANOVA followed by a Tukey post hoc test (P = 0.05). After debonding, the failure modes were analyzed using a stereomicroscope. The ZI group (72.6 MPa) showed the highest µTBS, followed by the ZB group (60.2 MPa), while the SI (34.4 MPa) and SB (42.6 MPa) groups demonstrated statistically significant lower bond strengths. The type of placement technique did not influence the µTBS of silorane-based composites to the bottom dentin of Class I cavities. The methacrylate-based composite showed superior performance, regardless of the placement technique.
General dentistry 11/2011; 59(6):e233-7.
-
[show abstract]
[hide abstract]
ABSTRACT: Dental erosion is a contemporary disease, mostly because of the change of the eating patterns that currently exist in society. It is a "silent" and multifactorial disease, and is highly influenced by habits and lifestyles. The prevalence of dental erosion has considerably increased, with this condition currently standing as a great challenge for the clinician, regarding the diagnosis, identification of the etiological factors, prevention, and execution of an adequate treatment. This article presents a dental erosion review and a case report of a restorative treatment of dental erosion lesions using a combination of bonded ceramic overlays to reestablish vertical dimension and composite resin to restore the worn palatal and incisal surfaces of the anterior upper teeth. Adequate function and esthetics can be achieved with this approach.
Journal of Esthetic and Restorative Dentistry 08/2011; 23(4):205-16. · 0.99 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Ultra-thin bonded posterior occlusal veneers represent a conservative alternative to traditional inlays and complete coverage crowns for the treatment of severe erosive lesions. There is a lack of data regarding selection of the most appropriate material and its influence on fatigue resistance, which may affect restoration longevity.
The purpose of this study was to assess the influence of CAD/CAM restorative material (ceramic vs. composite resin) on fatigue resistance of ultra-thin occlusal veneers.
A standardized nonretentive tooth preparation (simulating advanced occlusal erosion) was applied to 40 extracted molars including removal of occlusal enamel, and immediate dentin sealing (Optibond FL). All teeth were restored with a 0.6 mm-thick occlusal veneer (Cerec3 chairside CAD/CAM system). Reinforced ceramics (Empress CAD and e.max CAD) and composite resins (Paradigm MZ100 and XR (experimental blocks)) were used to mill the restorations (n=10). The intaglio surfaces were HF-etched and silanated (reinforced ceramics) or airborne-particle abraded and silanated (composite resins). Preparations were airborne-particle abraded and etched before restoration insertion. All restorations were adhesively luted with preheated Filtek Z100. Cyclic isometric loading was applied at 5 Hz, beginning with a load of 200N (x5,000), followed by stages of 400, 600, 800, 1000, 1200 and 1,400N at a maximum of 30,000 cycles each. The number of cycles at initial failure (first cracks) was recorded. Specimens were loaded until catastrophic failure (lost restoration fragment) or to a maximum of 185,000 cycles. Groups were compared using the life table survival analysis (α=.008, Bonferroni-method).
Empress CAD and e.max CAD initially failed at an average load of 500N and 800N, respectively with no specimen withstanding all 185,000 load cycles (survival 0%); with MZ100 and XR the survival rate was 60% and 100%, respectively.
Both composite resins (MZ100 and XR) increased the fatigue resistance of ultra-thin occlusal veneers (P<.001) when compared to the ceramics evaluated (Empress CAD and e.max CAD).
The Journal of prosthetic dentistry 04/2011; 105(4):217-26. · 1.22 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The aim of this study was to evaluate the fatigue limits of the dentin-composite interfaces established either with an etch-and-rinse or an one-step self-etch adhesive systems under tensile and bending configurations.
Flat specimens (1.2 mm×5 mm×35 mm) were prepared using a plexiglass mold where dentin sections from human third molars were bonded to a resin composite, exhibiting the interface centrally located. Syntac Classic and G-Bond were used as adhesives and applied according to the manufacturer's instructions. The fluorochrome Rhodamine B was added to the adhesives to allow for fractographic evaluation. Tensile strength was measured in an universal testing machine and the bending strength (n=15) in a Flex machine (Flex, University of Antwerp, Belgium), respectively. Tensile (TFL) and bending fatigue limits (BFL) (n=25) were determined under wet conditions for 10(4) cycles following a staircase approach. Interface morphology and fracture mechanisms were observed using light, confocal laser scanning and scanning electron microscopy. Statistical analysis was performed using three-way ANOVA (mod LSD test, p<0.05).
Tensile and bending characteristic strengths at 63.2% failure probability for Syntac were 23.8 MPa and 71.5 MPa, and 24.7 MPa and 72.3 MPa for G-Bond, respectively. Regarding the applied methods, no significant differences were detected between adhesives. However, fatigue limits for G-Bond (TFL=5.9 MPa; BFL=36.2 MPa) were significantly reduced when compared to Syntac (TFL=12.6 MPa; BFL=49.7 MPa). Fracture modes of Syntac were generally of adhesive nature, between the adhesive resin and dentin, while G-Bond showed fracture planes involving the adhesive-dentin interface and the adhesive resin.
Cyclic loading under tensile and bending configurations led to a significant strength degradation, with a more pronounced fatigue limit decrease for G-Bond. The greater decrease in fracture strength was observed in the tensile configuration.
Dental materials: official publication of the Academy of Dental Materials 12/2010; 26(12):1157-65. · 2.88 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: To evaluate the effect on bond strength of 1, 2, or 3 coats of two one-step self-etching adhesives on dentin covered with two different smear layer thicknesses.
Flat dentin surfaces from recently extracted third molars were wet ground with 60- or 600-grit SiC paper to produce smear layers of different thicknesses. Adper Easy Bond (3M ESPE) and Clearfil S3 Bond (Kuraray) were applied in 1, 2, or 3 consecutive coats after air drying each coat. ScotchBond Multi Purpose (3M) and Clearfil SE Bond (Kuraray) were used as controls. Composite resin crowns (Filtek Z250, 3M ESPE) were built up, stored for 24 h, and cut in x and y directions. Eight to twelve sticks (0.65 ± 0.05 mm2 of area) from the central area of each tooth were fractured in tension (0.5 mm/min). Sticks from each group were processed for interfacial micromorphological evaluation with SEM.
Three-way ANOVA revealed a significant interaction between factors (p < 0.05). Tukey's post-hoc test showed that only when Adper Easy Bond was applied on dentin prepared with 600-grit SiC paper, microtensile bond strength was not significantly affected by the number of coatings. However, the effect of smear layer thickness was only statistically significant when the adhesives were applied in one coat, for both adhesives. When they were applied in two or three coats, smear layer thickness did not significantly affect bond strength (p > 0.05).
The thickness of the smear layer affected the bond strength of both all-in-one adhesives. Additional coats can be beneficial to bond strength, especially with Clearfil S3 Bond.
The journal of adhesive dentistry 11/2010; 13(6):507-16. · 1.11 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: To evaluate the dentin bond durability of simplified adhesives after one-year (1 y) under water storage and simulated pulpal pressure.
Class I cavities were prepared in sixty human third molars with the pulpal wall located in mid-coronal dentin. The roots were cut off to expose the pulpal chamber, and the teeth were assembled in a pulpal pressure simulator device. A two-step etch-and-rinse adhesive (Single Bond 2/SB), a two-step self-etch adhesive (Clearfil SE Bond/CSE), a three-step self-etch adhesive (Adper Scotchbond SE/SSE) and three all-in-one adhesives (Adper Easy Bond/EB, Clearfil S(3) Bond/S3 and Adhese One/AO) were applied according to manufacturers instructions. No enamel pre-etching was used for the self-etch systems. The cavities were filled with a composite (Z250, 3M ESPE) in four to five horizontal increments and individually cured. Immediately after the final cure, pulpal pressure was set to 15 cm H(2)O. After 24 h and 1 y under simulate pulpal pressure the teeth were cut following a 'nontrimming' microtensile test technique (n=30) and tested in tension. Kruskall-Wallis and post hoc multiple comparisons were used at alpha=0.05. Weibull statistics was applied to SB, CSE and EB. Fractographic analysis of debonded specimens was performed using scanning electron microscopy.
At 24 h and 1 y periods, SB showed higher bond strength means than all the others adhesives tested. CSE was not statistically different from EB at 24 h and from EB and SB at 1 y. EB showed bond strength statistically higher than the other three self-etch adhesives, which were not statistically different from each other at 24 h. AO showed significantly lower bond strength than all tested materials after 1 y. For all adhesives the mean bond strength at 1 y were not statistically different from the values measured at 24 h (p>0.05). Shifts in failure mode patterns and Weibull modulus decrease indicate some degree of bond degradation after the 1 y storage period.
One-year of simulated pulpal pressure did not affect dentin bond strength of simplified adhesives in Class I restorations. Signs of degradation were only revealed by fractographic analysis and reliability parameters.
Journal of dentistry 10/2010; 38(10):802-10. · 2.00 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Thin, bonded, posterior occlusal veneers constitute a conservative alternative to traditional complete coverage crowns. Information regarding selection of the appropriate material and its influence on fatigue resistance, which may affect the longevity of the restoration, is missing.
The purpose of this study was to assess and compare the fatigue resistance of composite resin and ceramic posterior occlusal veneers.
Thirty extracted molars received a standardized nonretentive tooth preparation (simulating advanced occlusal erosion), including removal of occlusal enamel, exposure of dentin, and immediate dentin sealing (Optibond FL). All teeth were restored with a 1.2-mm-thick occlusal veneer (Cerec 3 chairside CAD/CAM system). The restorations (n=10) were milled from leucite-reinforced and lithium disilicate ceramics (IPS Empress CAD and IPS e.max CAD, respectively) and a composite resin (Paradigm MZ100). The intaglio surfaces of the ceramic restorations were conditioned by hydrofluoric acid etching and silane. Airborne-particle abrasion and silane were used to condition the composite resin restorations. Preparations were airborne-particle abraded and etched. All restorations were bonded with preheated luting material and submitted to cyclic isometric loading at 5 Hz, starting with a load of 200 N (x5000 cycles), followed by stepwise loading of 400, 600, 800, 1000, 1200, and 1400 N at a maximum of 30,000 cycles each. The number of cycles at initial failure (first cracks) was recorded. Specimens were loaded for a maximum of 185,000 cycles. Groups were compared using the life table survival analysis (alpha=.016, Bonferroni method).
IPS Empress CAD failed at an average load of 900 N, with no specimen withstanding all 185,000 load cycles (survival 0%), while IPS e.max CAD and Paradigm MZ100 demonstrated survival rates of 30% and 100%, respectively. None of the specimens exhibited catastrophic failure, but only cracks limited to the restorative material.
Posterior occlusal veneers made of composite resin (Paradigm MZ100) had significantly higher fatigue resistance (P<.002) compared to IPS Empress CAD and IPS e.max CAD.
The Journal of prosthetic dentistry 09/2010; 104(3):149-57. · 1.22 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: One of the challenges in clinical esthetic dentistry is closing anterior diastemas without creating "black triangles" between the teeth. The success of a restorative treatment in anterior teeth depends on the esthetic integration between soft tissues and hard tissues. The conditioning of the interdental papilla is a simple, direct, predictable, and low-cost alternative. This paper reports a case on diastema closure in anterior teeth that was successfully treated using gingival recontouring and composite resin restorations. CLINICAL SIGNIFICANCE: The closure of diastemas in anterior teeth using direct adhesive restorations and gingival recontouring is a viable option for the clinician because it restores esthetic harmony between soft and hard tissues.
Journal of Esthetic and Restorative Dentistry 02/2009; 21(4):229-40. · 0.99 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: To examine the effect of prolonged application time on the early and 3-year resin-dentin microtensile bond strength.
Water/ethanol (Single Bond [SB]) and acetone-based systems (One Step [OS]) were employed. A flat superficial dentin surface was exposed in third human molars by wet abrasion. The adhesives were applied to a delimited area of 52 mm2 on wet surfaces, for 40, 90, 150 and 300 s. Four teeth were assigned for each experimental condition. Composite build-ups were constructed incrementally. After water storage at 37 degrees C for 24 h, teeth were sectioned to obtain sticks with cross-sectional areas of 0.8 mm2 to be tested in tension (0.5 mm/min) either immediately (IM) or after 3 years (3Y) of water storage. The microtensile bond strength (microTBS) values were analyzed by two way repeated measures ANOVA and Tukey's test (alpha=0.05).
The 90- and 150-s groups achieved the highest IM microTBS for OS (p<0.01). For SB, the highest IM microTBS values were observed after 300-s application (p<0.01). Significant decreases in microTBS were observed for OS in the 40- and 90-s groups after 3Y, except for the 150-s group. With regard to SB, after 3Y significant drops in microTBS values were observed for the 40- and 150-s groups, except for the 300-s group.
Prolonged application times can increase the immediate microTBS of two-step etch-and-rinse adhesive systems and make the adhesive layer more stable over time.
Dental Materials 06/2008; 24(5):639-44. · 3.13 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Adhesive procedures are essential to most restorative protocols used in modern dentistry. Increasing demand and constant interest in new products have stimulated dental manufacturers to produce new adhesive systems and marketing campaigns that announce fast and easy bonding. However, laboratorial and clinical studies show that, usually, ease of application of an adhesive system does not relate to its competence in creating a quality, long-term adhesive interface. This article will present relevant data from the scientific literature to help clinicians understand quality adhesion and achieve excellent results with the current adhesion systems.
Compendium of continuing education in dentistry (Jamesburg, N.J.: 1995) 05/2008; 29(4):208-15; quiz 216, 218.
-
[show abstract]
[hide abstract]
ABSTRACT: This in situ study evaluated the influence of two home-applied bleaching agents (10% carbamide peroxide and 7.5% hydrogen peroxide) on enamel microhardness.
Ninety enamel slabs were obtained from human third molars and baseline Knoop hardness measurements were recorded under a 50 g load for 5s. The specimens were attached to intra-oral devices delivered to 10 volunteers (donor of the teeth) who used the devices 24h/day throughout the experiment. The specimens were divided in three groups, two experimental and one control; in the last group, enamel slabs were not submitted to bleaching agents, but exposed only to the action of saliva. Two custom-made trays were made for each volunteer to recover the teeth and the appliances containing the enamel slabs. The bleaching regimen was 1h/day for 21 consecutive days. Subsequently, additional hardness measurements were recorded.
The mean values of the baseline and final microhardness were: 348 and 352.2; 346.6 and 354.5; 342 and 340.8, for control, 10% carbamide peroxide and 7.5% hydrogen peroxide groups, respectively. One-way ANOVA of the microhardness mean values revealed no statistically significant differences among groups, the specimens treated with 7.5% hydrogen peroxide has shown a tendency (p=0.056) to microhardness decrease.
Data suggested that the tested home bleaching agents did not change the superficial enamel microhardness.
Journal of Dentistry 02/2008; 36(1):2-7. · 2.95 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Modern operative dentistry provides practitioners of esthetic dentistry the means for performing direct restorations in a virtually imperceptible way. However, this attribute of resin composite can cause difficulties because the absence of contrast between the tooth structure and the restoration can impede visualization of the cavity limits. The purpose of this article is to highlight some operative steps that, when appropriately performed, will facilitate the building of direct resin composite restorations in posterior teeth, significantly reducing the possibility of restorative overextension.
European journal of esthetic dentistry : official journal of the European Academy of Esthetic Dentistry, The 02/2008; 3(4):348-60.
-
[show abstract]
[hide abstract]
ABSTRACT: To examine the etching efficacy of three self-etching systems to unconditioned enamel and to phosphoric-acid conditioned enamel using scanning electron microscopy (SEM), and to investigate the microtensile bond strength (muTBS) of three self-etching adhesives to unconditioned enamel used according to the manufacturers' instructions, on phosphoric-acid conditioned enamel, and when their different adhesives were replaced with a control resin after etching.
Clearfil SE Bond (CSE), Tyrian SPE/One-Step Plus (TY), and Adper Prompt L-Pop (AD) were employed. Scotchbond Multi-Purpose Plus (SBMP), an etch-and-rinse adhesive, was used as control. For muTBS evaluation, the buccal or lingual mid-coronal enamel of 30 molars was used. In the first group, self-etching adhesives were applied conventionally, according to manufacturers' directions (group C). A second group of specimens was etched with 35% phosphoric acid before application of the self-etching adhesives (group PA), and the third group of specimens was etched with the self-etching adhesives, rinsed, but bonded using a control bonding resin (group CR). Following restoration with Z250, they were sectioned into beams (0.8 mm2), and stressed to failure. Data were subjected to two-way ANOVA and Tukey's test. The etching efficacy of the self-etching adhesives, phosphoric acid, and prior phosphoric acid + SE application was evaluated under SEM.
All self-etching adhesives applied as recommended by the manufacturers showed lower muTBS values than those obtained in PA and CR groups, although this difference was only significant for TY and AD. The means of all self-etching adhesives under PA and CR groups were similar to SBMP. The enamel conditioned with self-etching adhesive showed a less distinct pattern. CSE exhibited the mildest etching pattern. All self-etching adhesives applied after phosphoric acid exhibited a more retentive etching pattern.
The bond strength values of low-pH self-etching adhesives can be improved by the adjunctive use of phosphoric acid or replacement of the bonding resin.
The journal of adhesive dentistry 01/2008; 9(6):537-45. · 1.11 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The purpose of this in vitro study was to measure the microtensile bond strength of a nanofilled composite resin to human dentin after nonvital bleaching at different post-bleaching time intervals, and to analyze the fracture mode under SEM.
Thirty-six sound human maxillary premolars extracted for orthodontic reasons were prepared in a standardized manner, and randomly assigned to four groups (n = 9): non bleached (control) (NB); bleached with sodium perborate and 35% hydrogen peroxide (SP-HP); bleached with 35% hydrogen peroxide (HP); and bleached with 37% carbamide peroxide (CP). Each group was subdivided into 3 subgroups (n = 3): restored immediately (RO); restored after 7 days (R7); and restored after 14 days (R14). The teeth were stored in distilled water for 24 h, sectioned 4 mm below cementoenamel junction, and the crown was serially sectioned to obtain sticks (0.9 mm2 cross section) for microtensile bond strength testing. The microTBS samples were attached to a universal testing machine (Instron, model 4444), using a Geraldeli's device. The test was performed until the fracture of the specimens, and all specimens were analyzed under a scanning electron microscope (Philips XL-30).
Two-way ANOVA (p = 0.05) revealed that there were no statistically significant differences of bond strength values for the bleaching agents used, or at different post-bleaching time intervals.
It was concluded that the definitive restoration can be accomplished immediately after nonvital bleaching treatment.
The journal of adhesive dentistry 07/2007; 9(3):333-40. · 1.11 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: There are two bonding strategies for composite restorations: the etch-and-rinse (ER) approach and the self-etch (SE) approach. Few clinical trials have evaluated the SE approach in Class V restorations for a 36-month period. The authors conducted a study to evaluate whether the SE system can provide retention rates and marginal discoloration similar to that of the ER system.
Twenty-five patients, each having at least two pairs of equivalent noncarious cervical lesions under occlusion, were enrolled in this study. Two calibrated operators placed 78 restorations, one-half for ER and one-half for SE. Two independent examiners evaluated the restorations at baseline and after six-, 12-, 18- and 36-month periods according to the slightly modified U.S. Public Health Service criteria. Statistical analysis between materials in each period was conducted using a Fisher exact test (alpha = .05), and the performance of the materials at baseline in comparison with each period was evaluated by a McNemar test (alpha = .05).
Five SE restorations and one ER restoration were lost after 36 months. After 36 months, 10 SE and five ER restorations were rated Bravo in marginal adaptation (P > .05). Fourteen SE and five ER restorations were rated Bravo in marginal discoloration (P < .05).
Although a significantly increased marginal discoloration was observed with SE, both adhesives showed retention rates in noncarious cervical lesions that were not statistically different after 36 months.
The ER and SE adhesive systems can be used with confidence; however, SE adhesive showed a faster and more progressive enamel marginal degradation.
Journal of the American Dental Association (1939) 04/2007; 138(4):507-14; quiz 535-7. · 1.77 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: To portray and assess the interfacial morphology achieved with self-etching systems in dentin under observation by scanning electron microscopy.
Ten caries-free extracted erupted human third molars were used in this study. The occlusal enamel was removed, and 10 dentin disks with a thickness of 800 +/- 200 Microm were obtained by slow-speed sectioning with a diamond saw parallel to the occlusal surface. A standard smear layer was created on the occlusal surface by wet sanding with 600-grit sandpaper for 60 seconds. The dentin disks were randomly assigned to one of the systems: AdheSE (Ivoclar Vivadent), Optibond Solo Plus-Self-Etch (Kerr), Tyrian SPE (Bisco) as self-etching primers, and Adper Prompt Self-Etch (3M Espe) and One-Up Bond F (Tokuyama) as self-etching adhesives. All systems were applied according to the manufacturers' instructions. After application of the adhesive systems, a 1.0-mm-thick layer of a flowable composite resin (Filtek Flow; 3M Espe) was applied to the treated dentin surface and light cured for 40 seconds. The specimens were then processed for observation by scanning electron microscopy.
All self-etching systems achieved the formation of sealed interfaces and hybridized areas with variable extents except for the self-etching adhesive One-Up Bond F, which showed some gap formation and poor hybridization. Optibond Solo Plus-Self-Etch presented a more consistent adhesive interface with thicker hybrid layers, numerous resin tags, and lateral branches.
Regarding the micromorphology aspect, Optibond Solo Plus-Self-Etch showed the finest result, while One-Up Bond F was not able to produce a satisfactory ultrastructural morphology.
Quintessence international 03/2007; 38(2):e112-9. · 0.76 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: This article presents the essential aspects for understanding and reproducing the color of natural teeth with the use of direct resin composite. Fluorescence and opalescence are discussed, with special emphasis on counter-opalescence, which is primarily responsible for the appearance of an orange discoloration at the mamelon dentin tips and incisal edges of anterior teeth. The dynamics of color in natural teeth in relation to age is also discussed, focusing on the age-related changes that occur in enamel, dentin, and pulp. Further, it is demonstrated how to reproduce the esthetic features of natural teeth using latest-generation direct resin composites.
European journal of esthetic dentistry : official journal of the European Academy of Esthetic Dentistry, The 02/2007; 2(2):172-86.
-
[show abstract]
[hide abstract]
ABSTRACT: Light-emitting diode (LED) curing units are becoming increasingly popular; however, questions remain about their ability to adequately polymerize composite resins. This study was conducted to evaluate the marginal seal of restorations placed with a tungsten halogen curing unit compared to three LED curing units through a microleakage test. The results did not indicate statistical differences between the groups tested for both enamel and dentin margins. Variation of the light-curing unit (quartz tungsten halogen or LED) did not result in discernible differences in the marginal sealing of composite restorations.
Practical procedures & aesthetic dentistry: PPAD 08/2006; 18(6):345-51; quiz 352.
