-
[show abstract]
[hide abstract]
ABSTRACT: Based on a scanning electron microscope operated at 30 kV with a homemade specimen holder and a multiangle solid-state detector behind the sample, low-kV scanning transmission electron microscopy (STEM) is presented with subsequent electron tomography for three-dimensional (3D) volume structure. Because of the low acceleration voltage, the stronger electron-atom scattering leads to a stronger contrast in the resulting image than standard TEM, especially for light elements. Furthermore, the low-kV STEM yields less radiation damage to the specimen, hence the structure can be preserved. In this work, two-dimensional STEM images of a 1-μm-thick cell section with projection angles between ±50° were collected, and the 3D volume structure was reconstructed using the simultaneous iterative reconstructive technique algorithm with the TomoJ plugin for ImageJ, which are both public domain software. Furthermore, the cross-sectional structure was obtained with the Volume Viewer plugin in ImageJ. Although the tilting angle is constrained and limits the resulting structural resolution, slicing the reconstructed volume generated the depth profile of the thick specimen with sufficient resolution to examine cellular uptake of Au nanoparticles, and the final position of these nanoparticles inside the cell was imaged.
Microscopy and Microanalysis 10/2012; 18(5):1037-42. · 3.01 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: In the past decade, buckminsterfullerene (C(60))-based ion beams have been utilized in surface analysis instruments to expand their application to profiling organic materials. Although it had excellent performance for many organic and biological materials, its drawbacks, including carbon deposition, carbon penetration, continuous decay of the sputtering rate, and a rough sputtered surface, hindered its application. Cosputtering with C(60)(+) and auxiliary Ar(+) simultaneously and sample rotation during sputtering were proposed as methods to reduce the above-mentioned phenomena. However, the improvement from these methods has not been compared or studied under identical conditions; thus, the pros and cons of these methods are not yet known experimentally. In this work, a series of specimens including bulk materials and thin films were used to explore the differences between cosputtering and sample rotation on the analytical results. The results show that both of these methods can alleviate the problems associated with C(60)(+) sputtering, but each method showed better improvement in different situations. The cosputtering technique better suppressed carbon deposition, and could be used to generally improve results, especially with continuous spectra acquisition during sputtering (e.g., dynamic secondary ion mass spectrometry (SIMS) depth profiling). In contrast, for the scheme of sputter-then-acquire (e.g., alternative X-ray photoelectron spectrometry or dual-beam static SIMS depth profiling), a better result was achieved by sample rotation because it resulted in a flatter sputtered surface. Therefore, depending on the analytical scheme, a different method should be used to optimize the experimental conditions.
Analytical Chemistry 09/2012; · 5.86 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Gold is known to have good biocompatibility because of its inert activity and the surface property can be easily tailored with self-assembled monolayers (SAMs). In previous works, gold surfaces were tailored with homogeneously mixed amine and carboxylic acid functional groups to generate surfaces with a series of isoelectronic points (IEPs). In other words, by tailoring the chemical composition in binary SAMs, different surface potentials can be obtained under controlled pH environments. To understand how the surface potentials affect the interaction at the interface, a binary-SAMs-modified Au electrode on a quartz crystal microbalance with dissipation detection (QCM-D) was used owing to the high weight sensitivity of QCM-D. In QCM-D, the frequency shift and the energy dissipation are monitored simultaneously to determine the adsorption behaviors of the plasmid DNA to surfaces of various potentials in Tris-buffered NaCl solutions of different pH. The results revealed that the plasmid DNA can be adsorbed on the SAM-modified surfaces electrostatically; thus, in general, the amount of adsorbed plasmid DNA decreased with increasing environmental pH and the decreasing ratio of the amine functional groups on the surfaces owing to weaker positive potentials on the surface. For the high amine-containing surfaces, due to the strong electrostatic attraction, denser films were observed, and thus, the apparent thickness decreased slightly. The negatively charged carboxylic acid surfaces can still adsorb the negatively charged plasmid DNA at some conditions. In other words, the electrostatic model cannot explain the adsorption behavior completely, and the induced dipole (Debye) interaction between the charged and polarizable molecules needs to be considered as well.
Journal of Colloid and Interface Science 06/2012; 382(1):97-104. · 3.07 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Time-of-flight secondary ion mass spectrometry (ToF-SIMS) using pulsed C(60)(+) primary ions is a promising technique for analyzing biological specimens with high surface sensitivities. With molecular secondary ions of high masses, multiple molecules can be identified simultaneously without prior separation or isotope labeling. Previous reports using the C(60)(+) primary ion have been based on static-SIMS, which makes depth profiling complicated. Therefore, a dynamic-SIMS technique is reported here. Mixed peptides in the cryoprotectant trehalose were used as a model for evaluating the parameters that lead to the parallel detection and quantification of biomaterials. Trehalose was mixed separately with different concentrations of peptides. The peptide secondary ion intensities (normalized with respect to those of trehalose) were directly proportional to their concentration in the matrix (0.01-2.5 mol%). Quantification curves for each peptide were generated by plotting the percentage of peptides in trehalose versus the normalized SIMS intensities. Using these curves, the parallel detection, identification, and quantification of multiple peptides was achieved. Low energy Ar(+) was used to co-sputter and ionize the peptide-doped trehalose sample to suppress the carbon deposition associated with C(60)(+) bombardment, which suppressed the ion intensities during the depth profiling. This co-sputtering technique yielded steadier molecular ion intensities than when using a single C(60)(+) beam. In other words, co-sputtering is suitable for the depth profiling of thick specimens. In addition, the smoother surface generated by co-sputtering yielded greater depth resolution than C(60)(+) sputtering. Furthermore, because C(60)(+) is responsible for generating the molecular ions, the dosage of the auxiliary Ar(+) does not significantly affect the quantification curves.
Analytica chimica acta 03/2012; 718:64-9. · 4.31 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: To explore C(60)(+) sputtering beyond low-damage depth profiling of organic materials, X-ray photoelectron spectrometry (XPS) and secondary ion mass spectrometry (SIMS) were used to examine metallic surfaces during and after C(60)(+) sputtering. During C(60)(+) sputtering, XPS spectra indicated that the degrees of carbon deposition were different for different metallic surfaces. Moreover, for some metals (e.g., Al, W, Ta, Ti, and Mo), the intensity of the O 1s photoelectron increased significantly during C(60)(+) sputtering, even though the instrument was under ultrahigh vacuum (<5 × 10(-7) Pa). This result indicated that the rate of oxygen uptake was greater than the rate of C(60)(+) sputtering. This behavior was not observed with the commonly used Ar(+) sputtering. To measure the oxygen uptake kinetics, pure oxygen was leaked into the chamber to maintain a 5 × 10(-6) Pa oxygen environment. The C(60)(+)-sputtered surface had a clearly increased rate of oxygen uptake than the Ar(+)-sputtered surface, even for moderately reactive metals such as Fe and Ni. For relatively nonreactive metals such as Cu and Au, a small amount of carbon was implanted and no oxygen uptake was observed. High-resolution XPS spectra revealed the formation of metal carbides on these reactive metals, and the carbon deposition and enhanced uptake of oxygen correlated to the carbide formation. Because oxygen enhances the secondary ion yield through surface passivation, the enhanced oxygen uptake due to C(60)(+) sputtering could be beneficial for SIMS analysis. To examine this hypothesis, C(60)(+) and Ar(+) were used as primary ions, and it was found that the intensity enhancement (because of the oxygen flooding at 5 × 10(-6) Pa) was much higher with C(60)(+) than with Ar(+). Therefore, oxygen flooding during C(60)(+) sputtering has a great potential for enhancing the detection limit due to the enhanced oxygen uptake.
Analytical Chemistry 03/2012; 84(7):3355-61. · 5.86 Impact Factor
-
Yun-Wen You,
Hsun-Yun Chang,
Wei-Chun Lin,
Che-Hung Kuo,
Szu-Hsian Lee,
Wei-Lun Kao,
Guo-Ji Yen,
Chi-Jen Chang,
Chi-Ping Liu,
Chih-Chieh Huang,
Hua-Yang Liao,
Jing-Jong Shyue
[show abstract]
[hide abstract]
ABSTRACT: Dynamic secondary ion mass spectrometry (D-SIMS) analysis of poly(ethylene terephthalate) (PET) and poly(methyl methacrylate) (PMMA) was conducted using a quadrupole mass analyzer with various combinations of continuous C(60)(+) and Ar(+) ion sputtering. Individually, the Ar(+) beam failed to generate fragments above m/z 200, and the C(60)(+) beam generated molecular fragments of m/z ~1000. By combining the two beams, the auxiliary Ar(+) beam, which is proposed to suppress carbon deposition due to C(60)(+) bombardment and/or remove graphitized polymer, the sputtering range of the C(60)(+) beam is extended. Another advantage of this technique is that the high sputtering rate and associated high molecular ion intensity of the C(60)(+) beam generate adequate high-mass fragments that mask the damage from the Ar(+) beam. As a result, fragments at m/z ~900 can be clearly observed. As a depth-profiling tool, the single C(60)(+) beam cannot reach a steady state for either PET or PMMA at high ion fluence, and the intensity of the molecular fragments produced by the beam decreases with increasing C(60)(+) fluence. As a result, the single C(60)(+) beam is suitable for profiling surface layers with limited thickness. With C(60)(+)-Ar(+) co-sputtering, although the initial drop in intensity is more significant than with single C(60)(+) ionization because of the damage introduced by the auxiliary Ar(+), the intensity levels indicate that a more steady-state process can be achieved. In addition, the secondary ion intensity at high fluence is higher with co-sputtering. As a result, the sputtered depth is enhanced with co-sputtering and the technique is suitable for profiling thick layers. Furthermore, co-sputtering yields a smoother surface than single C(60)(+) sputtering.
Rapid Communications in Mass Spectrometry 10/2011; 25(19):2897-904. · 2.79 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: It has been shown that the application of self-assembled monolayers (SAMs) to semiconductors or metals may enhance the efficiency of optoelectronic devices by changing the surface properties and tuning the work functions at their interfaces. In this work, binary SAMs with various ratios of 3-aminopropyltrimethoxysilane (APTMS) and 3-mercaptopropyltrimethoxysilane (MPTMS) were used to modify the surface of Si to fine-tune the work function of Si to an arbitrary energy level. As an electron-donor, amine SAM (from APTMS) produced outward dipole moments, which led to a lower work function. Conversely, electron-accepting thiol SAM (from MPTMS) increased the work function. It was found that the work function of Si changed linearly with the chemical composition and increased with the concentration of thiol SAMs. Because dipoles of opposite directions cancelled each other out, homogeneously mixing them leads to a net dipole moment (hence the additional surface potential) between the extremes defined by each dipole and changes linearly with the chemical composition. As a result, the work function changed linearly with the chemical composition. Furthermore, the amine SAM possessed a stronger dipole than the thiol SAM. Therefore, the SAMs modified with APTMS showed a greater work function shift than did the SAMs modified with MPTMS.
Physical Chemistry Chemical Physics 09/2011; 13(33):15122-6. · 3.57 Impact Factor
-
Wei-Chun Lin,
Chi-Ping Liu,
Che-Hung Kuo,
Hsun-Yun Chang,
Chi-Jen Chang,
Tung-Han Hsieh,
Szu-Hsian Lee, Yun-Wen You,
Wei-Lun Kao,
Guo-Ji Yen,
Chih-Chieh Huang,
Jing-Jong Shyue
[show abstract]
[hide abstract]
ABSTRACT: Cluster ion sputtering has been proven to be an effective technique for depth profiling of organic materials. In particular, C(60)(+) ion beams are widely used to profile soft matter. The limitation of carbon deposition associated with C(60)(+) sputtering can be alleviated by concurrently using a low-energy Ar(+) beam. In this work, the role of this auxiliary atomic ion beam was examined by using an apparatus that could analyze the sputtered materials and the remaining target simultaneously using secondary ion mass spectrometry (SIMS) and X-ray photoelectron spectrometry (XPS), respectively. It was found that the auxiliary 0.2 kV Ar(+) stream was capable of slowly removing the carbon deposition and suppresses the carbon from implantation. As a result, a more steady sputtering condition was achieved more quickly with co-sputtering than by using C(60)(+) alone. Additionally, the Ar(+) beam was found to interfere with the C(60)(+) beam and may lower the overall sputtering rate and secondary ion intensity in some cases. Therefore, the current of this auxiliary ion beam needs to be carefully optimized for successful depth profiling.
The Analyst 03/2011; 136(5):941-6. · 4.23 Impact Factor
-
Szu-Hsian Lee,
Wei-Chun Lin,
Chi-Jen Chang,
Chih-Chieh Huang,
Chi-Ping Liu,
Che-Hung Kuo,
Hsun-Yun Chang, Yun-Wen You,
Wei-Lun Kao,
Guo-Ji Yen,
Ding-Yuan Kuo,
Yu-Ting Kuo,
Meng-Hung Tsai,
Jing-Jong Shyue
[show abstract]
[hide abstract]
ABSTRACT: This study demonstrated that the work function (Φ) of Au substrates can be fine-tuned by using series ratios of binary self-assembled monolayers (SAMs). By using pure amine- and carboxylic acid-bearing alkanethiol SAM on gold substrates, Φ of Au changed from 5.10 to 5.16 and 5.83, respectively, as determined by ultra-violet photoelectron spectrometry (UPS). The shift in Φ due to the use of different functional groups was rationalized by considering the dipole moments of the molecules anchored on the Au surface. A series of binary SAMs were fabricated by mixing carboxylic acid- and amine-terminated alkanethiols in the deposition solution. By mixing these functional groups in SAMs, a linear correlation between Φ with respect to chemical composition (hence the effective dipole moment on the Au surface) was observed. It was found that arbitrary Φ between extremes (5.16 and 5.83) controlled by respective functional groups can be obtained by changing the chemical composition of SAMs. The Scanning Kelvin Probe (SKP) was also used to measure the contact potential difference (CPD) between SAMs and referencing Au on a patterned substrate prepared by photo-lithography. It was found that the CPD of SAMs with different chemical compositions correlates to their Φ. However, the magnitude of the CPD was smaller than the difference in Φ measured by UPS that was possibly due to the adsorption of contaminants in air.
Physical Chemistry Chemical Physics 03/2011; 13(10):4335-9. · 3.57 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: Self-assembled monolayer (SAM)-modified nano-materials are a new technology to deliver drug molecules. While the majority of these depend on covalently immobilizing molecules on the surface, it is proposed that electrostatic interactions may be used to deliver drugs. By tuning the surface potential of solid substrates with SAMs, drug molecules could be either absorbed on or desorbed from substrates through the difference in electrostatic interactions around the selected iso-electric point (IEP). In this work, the surface of silicon substrates was tailored with various ratios of 3-aminopropyltrimethoxysilane (APTMS) and 3-mercaptopropyltrimethoxysilane (MPTMS), which form amine- and thiol-bearing SAMs, respectively. The ratio of the functional groups on the silicon surface was quantified by X-ray photoelectron spectrometry (XPS); in general, the deposition kinetics of APTMS were found to be faster than those of MPTMS. Furthermore, for solutions with high MPTMS concentrations, the relative deposition rate of APTMS increased dramatically due to the acid-base reaction in the solution and subsequent electrostatic interactions between the molecules and the substrate. The zeta potential in aqueous electrolytes was determined with an electro-kinetic analyzer. By depositing SAMs of binary functional groups in varied ratios, the surface potential and IEP of silicon substrates could be fine-tuned. For <50% amine concentration in SAMs, the IEP changed linearly with the chemical composition from <2 to 7.18. For higher amine concentrations, the IEP slowly increased with concentration to 7.94 because the formation of hydrogen-bonding suppressed the subsequent protonation of amines.
Physical Chemistry Chemical Physics 03/2011; 13(9):3649-53. · 3.57 Impact Factor
-
Bang-Ying Yu,
Che-Hung Kuo,
Wei-Ben Wang,
Guo-Ji Yen,
Shin-ichi Iida,
Sun-Zen Chen,
Wei-Chun Lin,
Szu-Hsian Lee,
Wei-Lun Kao,
Chia-Yi Liu,
Hsun-Yun Chang, Yun-Wen You,
Chi-Jen Chang,
Chi-Ping Liu,
Jwo-Huei Jou,
Jing-Jong Shyue
[show abstract]
[hide abstract]
ABSTRACT: The nanostructure of the light emissive layer (EL) of polymer light emitting diodes (PLEDs) was investigated using force modulation microscopy (FMM) and scanning time-of-flight secondary ion mass spectrometry (ToF-SIMS) excited with focused Bi(3)(2+) primary beam. Three-dimensional nanostructures were reconstructed from high resolution ToF-SIMS images acquired with different C(60)(+) sputtering times. The observed nanostructure is related to the efficiency of the PLED. In poly(9-vinyl-carbazole) (PVK) based EL, a high processing temperature (60 °C) yielded less nanoscale phase separation than a low processing temperature (30 °C). This nanostructure can be further suppressed by replacing the host polymer with poly[oxy(3-(9H-9-carbazol-9-ilmethyl-2-methyltrimethylene)] (SL74) and poly[3-(carbazol-9-ylmethyl)-3-methyloxetane] (RS12), which have similar chemical structures and energy levels as PVK. The device efficiency increases when the phase separation inside the EL is suppressed. While the spontaneous formation of a bicontinuous nanostructure inside the active layer is known to provide a path for charge carrier transportation and to be the key to highly efficient polymeric solar cells, these nanostructures are less efficient for trapping the carrier inside the EL and thus lower the power conversion efficiency of the PLED devices.
The Analyst 10/2010; 136(4):716-23. · 4.23 Impact Factor
-
Bang-Ying Yu,
Chia-Yi Liu,
Wei-Chun Lin,
Wei-Ben Wang,
I-Ming Lai,
Sun-Zen Chen,
Szu-Hsian Lee,
Che-Hung Kuo,
Wei-Lun Kao, Yun-Wen You,
Chi-Ping Liu,
Hsun-Yun Chang,
Jwo-Huei Jou,
Jing-Jong Shyue
[show abstract]
[hide abstract]
ABSTRACT: By using 10 kV C(60)(+) and 200 V Ar(+) ion co-sputtering, a crater was created on the light-emitting layer of phosphorescent polymer light-emitting diodes, which consisted of a poly(9-vinyl carbazole) (PVK) host doped with a 24 wt % iridium(III)bis[(4,6-difluorophenyl)pyridinato-N,C(2)] (FIrpic) guest. A force modulation microscope (FMM) was used to analyze the nanostructure at the flat slope near the edge of the crater. The three-dimensional distribution of PVK and FIrpic was determined based on the difference in their mechanical properties from FMM. It was found that significant phase separation occurred when the luminance layer was spin coated at 30 degrees C, and the phase-separated nanostructure provides a route for electron transportation using the guest-enriched phase. This does not generate excitons on the host, which would produce photons less effectively. On the other hand, a more homogeneous distribution of molecules was observed when the layer was spin coated at 60 degrees C. As a result, a 30% enhancement in device performance was observed.
ACS Nano 05/2010; 4(5):2547-54. · 10.77 Impact Factor
-
Bang-Ying Yu,
Wei-Chun Lin,
Wei-Ben Wang,
Shin-Ichi Iida,
Sun-Zen Chen,
Chia-Yi Liu,
Che-Hung Kuo,
Szu-Hsian Lee,
Wei-Lun Kao,
Guo-Ji Yen, Yun-Wen You,
Chi-Ping Liu,
Jwo-Huei Jou,
Jing-Jong Shyue
[show abstract]
[hide abstract]
ABSTRACT: Solution processable fullerene and copolymer bulk heterojunctions are widely used as the active layers of solar cells. In this work, scanning time-of-flight secondary ion mass spectrometry (ToF-SIMS) is used to examine the distribution of [6,6]phenyl-C61-butyric acid methyl ester (PCBM) and regio-regular poly(3-hexylthiophene) (rrP3HT) that forms the bulk heterojunction. The planar phase separation of P3HT:PCBM is observed by ToF-SIMS imaging. The depth profile of the fragment distribution that reflects the molecular distribution is achieved by low energy Cs(+) ion sputtering. The depth profile clearly shows a vertical phase separation of P3HT:PCBM before annealing, and hence, the inverted device architecture is beneficial. After annealing, the phase segregation is suppressed, and the device efficiency is dramatically enhanced with a normal device structure. The 3D image is obtained by stacking the 2D ToF-SIMS images acquired at different sputtering times, and 50 nm features are clearly differentiated. The whole imaging process requires less than 2 h, making it both rapid and versatile.
ACS Nano 02/2010; 4(2):833-40. · 10.77 Impact Factor
