-
[show abstract]
[hide abstract]
ABSTRACT: The uptake kinetics of 27 emerging pollutants on the polar C18 Chemcatcher have been investigated. This investigation determined the sampling rates of 20 compounds, including 16 endocrine disruptors and 4 pharmaceuticals, which were used as overall pollution indicators. Calibrations were completed in a 50-L flow-through microcosm with continuous renewal of tap water spiked with approximately 3 μg/L of each pollutant and with sampling times at 1, 3, 6 and 12h and 1, 3, 7, 14, 21 and 28 days. Exponential regressions for the accumulation kinetics were plotted to confirm the maximum linear uptake times for each molecule using the half time of equilibrium (t(1/2)) criteria. Of the compounds tested, 17 were accumulated linearly for up to 14 or 21 days with an R(2) above 0.98 for linear correlations. The evaluation of the release kinetics of a C18 Chemcatcher spiked with 20 deuterated compounds identified 3 potential performance reference compounds (PRCs) with exponential desorption rates showing relatively good isotropic exchange.
Journal of chromatography. A 03/2012; 1237:37-45. · 4.19 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The next challenge of wastewater treatment is to reliably remove micropollutants at the microgram per litre range. During the present work more than 100 substances were analysed through on-site mass balances over 19 municipal wastewater treatment lines. The most relevant substances according to their occurrence in raw wastewater, in treated wastewater and in sludge were identified, and their fate in wastewater treatment processes was assessed. About half of priority substances of WFD were found at concentrations higher than 0.1 μg/L in wastewater. For 26 substances, potential non-compliance with Environmental Quality Standard of Water Framework Directive has been identified in treated wastewater, depending on river flow. Main concerns are for Cd, DEHP, diuron, alkylphenols, and chloroform. Emerging substances of particular concern are by-products, organic chemicals (e.g. triclosan, benzothiazole) and pharmaceuticals (e.g. ketoprofen, diclofenac, sulfamethoxazole, carbamazepine). About 80% of the load of micropollutants was removed by conventional activated sludge plants, but about two-thirds of removed substances were mainly transferred to sludge.
Water Science & Technology 01/2012; 65(7):1179-89. · 1.12 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The next challenge of wastewater treatment is to reliably remove micro-pollutants at the microgram per litre range in order to meet reuse applications and contribute to reach the good status of the water bodies. A hundred priority and relevant emerging substances were measured to evaluate at full-scale the removal efficiencies of seven advanced treatment lines (one membrane bioreactor process and six tertiary treatment lines) that were designed for reuse applications. To reliably compare the processes, specific procedures for micro-pollutants were applied for sampling, analysis and calculation of removal efficiencies. The membrane bioreactor process allowed to upgrade the removal efficiencies of about 20% of the substances measured, especially those that were partially degraded during conventional processes. Conventional tertiary processes like high rate clarification, sand filtration and polishing pond achieved significant removal for some micro-pollutants, especially for adsorbable substances. Advanced tertiary processes, like ozonation, activated carbon and reverse osmosis were all very efficient to complete the removal of polar pesticides and pharmaceuticals; metals and less polar substances were better retained by reverse osmosis.
Water Science & Technology 01/2011; 63(11):2486-97. · 1.12 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The next challenge of wastewater treatment is to reliably remove micro-pollutants at the microgram per litre range in order to meet the environmental quality standards set by new regulations like the Water Framework Directive. The present work assessed the efficiency of different types of primary, secondary and tertiary processes for the removal of more than 100 priority substances and other relevant emerging pollutants through on-site mass balances over 19 municipal wastewater treatment lines. Secondary biological processes proved to be in average 30% more efficient than primary settling processes. The activated sludge (AS) process led to a significant reduction of pollution loads (more than 50% removal for 70% of the substances detected). Biofilm processes led to equivalent removal efficiencies compared to AS, except for some pharmaceuticals. The membrane bioreactor (MBR) process allowed to upgrade removal efficiencies of some substances only partially degraded during conventional AS processes. Preliminary tertiary processes like tertiary settling and sand filtration could achieve significant removal for adsorbable substances. Advanced tertiary processes, like ozonation, activated carbon and reverse osmosis were all very efficient (close to 100%) to complete the removal of polar pesticides and pharmaceuticals; less polar substances being better retained by reverse osmosis.
Water Science & Technology 01/2011; 63(1):57-65. · 1.12 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: This study aims at evaluating occurrence and treatment efficiency of five estrogenic hormones and ten beta blockers in wastewater treatment plants (WWTP). The use of consistent sampling procedures, analytical techniques and data processing enabled to achieve an accurate comparison of the performances of the different treatment processes. First, the occurrence of molecules was evaluated in fourteen rural and urban WWTP located in France. Free and total estrogens were analyzed showing that more than 84% of estrogens in the dissolved phase of influent samples are in the free form. In effluent samples, comparable mean values but higher variation are underlined (RSD from 13 to 54% depending on the estrogen, compared to 11-21% for influents). Most of the target molecules are quantified in 30 influent and 31 effluent samples. Similar occurrence frequencies are obtained for influents from rural (6 WWTP) and urban areas (8 WWTP), except for betaxolol which is only quantified in urban wastewaters. Removal efficiencies of 8 biological treatments were studied: suspended growth biomass (activated sludge) and attached growth systems (biofilter, rotating biological contactor, reed-bed filter, trickling filter). Biological treatments are efficient to remove estrogens from the dissolved phase, with removal rate around 90%. For beta blockers, acebutolol and nadolol are efficiently removed (mean removal rate of 80%), whereas sotalol and propranolol are hardly impacted by biological treatments (removal rate below 20%). Finally, 9 tertiary treatment processes were evaluated. Ozonation, reverse osmosis and activated carbon filtration prove a high removal efficiency for beta blockers (above 80%). On the contrary, high speed chemical settler, sand filtration, silex filtration, microfiltration and UV present generally removal rates below 30% for all beta blockers. The polishing pond studied presents variable removal performances depending on the molecules (up to 75% for propranolol). The role of the hydraulic retention time on the removal efficiencies is confirmed.
Science of The Total Environment 09/2010; 408(19):4257-69. · 3.29 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: We created a database in order to quantitatively assess the occurrence and removal efficiency of pharmaceuticals and personal care products (PPCPs) in wastewater treatment plants (WWTPs). From 117 scientific publications, we compiled 6641 data covering 184 PPCPs. Data included the concentrations of PPCPs in WWTP influents and effluents, their removal efficiency and their loads to the aquatic environment. The first outputs of our database allowed to identify the most investigated PPCPs in WWTPs and the most persistent ones, and to obtain reliable and quantitative values on their concentrations, frequency of detection and removal efficiency in WWTPs. We were also able to compare various processes and pointed out activated sludge with nitrogen treatment and membrane bioreactor as the most efficient ones.
Environmental pollution (Barking, Essex: 1987) 03/2009; 157(5):1721-6. · 3.43 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: We created a database in order to quantitatively assess the occurrence and removal efficiency of PPCPs in WWTPs. From 113 scientific publications, we compiled 5887 data on the concentrations and loads of PPCPs in WWTP influents and effluents, and on their removal efficiency. The first outputs of our database include: (1) a list of the most frequently studied molecules, their frequency of detection, their mean concentration and removal in liquid influent and effluent; (2) a comparison of the removal efficiency for different WWTP processes; (3) a study of the influence of the operating conditions (sludge and hydraulic retention times).
Water Science & Technology 02/2008; 57(1):49-56. · 1.12 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: There is a need for a better characterization of sludges from wastewater treatment plants which are destined to be spread on agricultural lands. Inorganic pollutants are regularly controlled but organic pollutants have received few attention up to now. On this paper, we have been interested on the analysis of the 16 polycyclic aromatic hydrocarbons (PAHs) listed in the US Environmental Protection Agency (US EPA) priority list and more particularly of the six PAHs listed in the European community list (fluoranthene, benzo[b and k]fluoranthene, benzo[a]pyrene, benzo[ghi]perylene, indeno[1,2,3-cd]pyrene). The analysis step consists on liquid chromatography with both fluorescence and UV detections as described in the EPA Method 8310. As for the extraction step, several techniques such as supercritical fluid extraction, pressurized liquid extraction, focused microwave extraction in open vessels, Soxhlet and ultrasonic extractions are compared after optimization of the experimental conditions (solvent nature and quantity, temperature, pressure, duration, ... ) and validation with certified sludges. When optimized, these five extraction techniques are as much efficient with similar relative standard deviation. Whatever the extraction techniques used, the whole analysis protocol permits to quantify PAHs in the range of 0.09 to 0.9 mg/kg of dried sludges.
Journal of Chromatography 06/2003; 995(1-2):87-97. · 4.53 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: A selective clean-up procedure using immunoaffinity solid-phase extraction was applied for the trace-level determination of polycyclic aromatic hydrocarbons (PAHs) in urban waste water and sewage sludges used for soil amendment. Anti-pyrene antibodies have been immobilized on a silica-based sorbent and the cross-reactivity of the antibodies towards structurally related compounds were allowed to extract the whole class of priority PAHs. The selectivity of the antibodies provided clean extracts from sludges and, therefore, the identification and quantification were shown to be easier using either liquid chromatography (LC) with UV diode array and fluorescence detection in series or gas chromatography-mass spectrometry (GC-MS), although some loss of up to 50% was observed for the clean-up. The identification of the PAHs by matching of UV and MS spectra was greatly improved. The procedure, including immunoclean-up and LC coupled to diode array and fluorescence detection, was validated using certified reference materials with native PAHs of concentrations in the range of 0.57-2.16 mg/kg (dry sludges).
Journal of Chromatography 11/1999; 859(1):29-39. · 4.53 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: There is a need for a better characterization of sludges from wastewater treatment plants which are destined to be spread on agricultural land. Inorganic pollutants are regularly controlled, but organic pollutants have received little attention up to now. The main problem for trace analysis of organic pollutants comes from the complexity of the various matrices of sludges, which depends on their origins. Therefore, methods described for soils and sediments cannot be directly applied to sludges which contain high amount of lipids. This paper provides a method for trace-determination of polycyclic aromatic hydrocarbons in the range of mg/kg of dried sludge including an extraction step, and an analysis step by liquid chromatography with fluorescence detection for sensitive quantification and UV-diode-array detection for confirmation. The extraction step was optimized by a selection of the solvent used for both Soxhlet and supercritical-fluid extraction and by setting the experimental conditions (temperature, pressure, modifier, etc.) used for SFE. Extraction recoveries were found similar and quantitative for the two procedures. However supercritical-fluid extraction appears to be a good alternative to Soxhlet extraction because of the consumption of less time and solvent. Detection limits were obtained in the range of 0.1-1 mg/kg of dried sludges, with possible confirmation by UV spectra. The whole method (extraction/quantification/confirmation) was validated using sludges which have been certified by the Community Bureau of Reference from Brussels (CRM No. 088). Application to the determination of PAHs in urban sludges is presented.
Journal of Chromatography 11/1998; 823(1-2):219-30. · 4.53 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: The parameters governing solid-phase microextraction (SPME) are investigated, with emphasis on the determination of the partition coefficients, K, and their use to predict the selection of a fibre, depending on the respective characteristics of the fibres and the analytes. Film thickness and stability of the compounds can interfere with the determination of K values. The time profile curves were determined for twelve pesticides having a wide range of water solubilities and polarities and using four fibres (polydimethylsiloxane, polydimethylsiloxane-divinylbenzene, Carbowax-divinylbenzene and polyacrylate). Although the affinity order was different for the four coatings, no correlation was found between the respective characteristics of the fibres and solutes. The two fibres containing divinylbenzene were shown to have the highest affinities and the polydimethylsiloxane had the lowest affinity. The polyacrylate fibre which is the more polar commercial fibre did not provide the highest affinities for the more polar and water-soluble analytes. The important parameters for quantitative analysis have been evaluated. The calibration curves were similar when one analyte of interest was present on its own in a drinking water sample, or when eleven other pesticides were present at the same concentration or when much higher concentrations of other analytes were present in the sample. Linearity was obtained over a wide range of concentrations in drinking water samples. Detection limits are in agreement with European regulatory levels in drinking water for most of the analytes using solid-phase microextraction-gas chromatography-nitrogen-phosphorus detection (SPME-GC-NPD). In contaminated surface water samples, the chromatograms are relatively clean and most of the compounds can be detected at levels lower than 0.5 microgram/l.
Journal of Chromatography 01/1998; 795(1):27-42. · 4.53 Impact Factor
-
[show abstract]
[hide abstract]
ABSTRACT: This study aims at evaluating occurrence and treatment efficiency of five estrogenic hormones and ten beta blockers in wastewater treatment plants (WWTP). The use of consistent sampling procedures, analytical techniques and data processing enabled to achieve an accurate comparison of the performances of the different treatment processes. First, the occurrence of molecules was evaluated in fourteen rural and urban WWTP located in France. Free and total estrogens were analyzed showing that more than 84% of estrogens in the dissolved phase of influent samples are in the free form. In effluent samples, comparable mean values but higher variation are underlined (RSD from 13 to 54% depending on the estrogen, compared to 11–21% for influents). Most of the target molecules are quantified in 30 influent and 31 effluent samples. Similar occurrence frequencies are obtained for influents from rural (6 WWTP) and urban areas (8 WWTP), except for betaxolol which is only quantified in urban wastewaters. Removal efficiencies of 8 biological treatments were studied: suspended growth biomass (activated sludge) and attached growth systems (biofilter, rotating biological contactor, reed-bed filter, trickling filter). Biological treatments are efficient to remove estrogens from the dissolved phase, with removal rate around 90%. For beta blockers, acebutolol and nadolol are efficiently removed (mean removal rate of 80%), whereas sotalol and propranolol are hardly impacted by biological treatments (removal rate below 20%). Finally, 9 tertiary treatment processes were evaluated. Ozonation, reverse osmosis and activated carbon filtration prove a high removal efficiency for beta blockers (above 80%). On the contrary, high speed chemical settler, sand filtration, silex filtration, microfiltration and UV present generally removal rates below 30% for all beta blockers. The polishing pond studied presents variable removal performances depending on the molecules (up to 75% for propranolol). The role of the hydraulic retention time on the removal efficiencies is confirmed.
Science of The Total Environment.
-
[show abstract]
[hide abstract]
ABSTRACT: We created a database in order to quantitatively assess the occurrence and removal efficiency of pharmaceuticals and personal care products (PPCPs) in wastewater treatment plants (WWTPs). From 117 scientific publications, we compiled 6641 data covering 184 PPCPs. Data included the concentrations of PPCPs in WWTP influents and effluents, their removal efficiency and their loads to the aquatic environment. The first outputs of our database allowed to identify the most investigated PPCPs in WWTPs and the most persistent ones, and to obtain reliable and quantitative values on their concentrations, frequency of detection and removal efficiency in WWTPs. We were also able to compare various processes and pointed out activated sludge with nitrogen treatment and membrane bioreactor as the most efficient ones.
Environmental Pollution.
