Article

Continuous-wave 1.55 microm diode-pumped surface emitting semiconductor laser for broadband multiplex spectroscopy.

Laboratoire de Photophysique Moléculaire, CNRS, Université de Paris-Sud, Orsay Cedex, France.
Optics Letters (Impact Factor: 3.18). 07/2007; 32(11):1387-9. DOI: 10.1364/OL.32.001387
Source: PubMed

ABSTRACT A room-temperature-operating vertical external cavity surface emitting laser is applied around 1550 nm to intracavity laser absorption spectroscopy analyzed by time-resolved Fourier-transform interferometry. At an equivalent path length of 15 km, the high-resolution spectrum of the semiconductor disk laser emission covers 17 nm simultaneously. A noise-equivalent absorption coefficient at 1 s averaging equal to 1.5 x 10(-10) cm(-1)Hz(-1/2) per spectral element is reported for 65 km, the longest path length employed.

0 Bookmarks
 · 
95 Views
  • [Show abstract] [Hide abstract]
    ABSTRACT: We firstly investigate the dynamics of vertical-cavity surface-emitting lasers (VCSELs) subject to sinusoidally modulated current using numerical simulations. For a few-hundred MHz frequency of injection current, the VCSELs emit a single pulse or a package of pulses when the injection current fluctuates around the threshold current. By varying the amplitude of the modulation, we show that the width of the bistability hysteresis loop can be suppressed and replaced by smooth single or multiple switching. For a few GHz frequency of injection current, the polarization modes of VCSELs exhibit a period-doubling transition to chaotic behavior. Then by modulating the VCSELs pump current by one of the outputs of a Rössler oscillator, we generate dynamical behaviors found in VCSELs subject to a sinusoidally modulated current. This new way of modulation of semiconductor lasers would bring a general benefit in the physical equipment, and reduce their cost.
    European Physical Journal Plus 05/2012; 127:46. · 1.48 Impact Factor
  • Source
    [Show abstract] [Hide abstract]
    ABSTRACT: processing, biology and medicine, spectroscopy, imaging, entertainment, and many others. A number of properties enable the application of lasers in these diverse areas, each application requiring a particular combination of these properties. Some of the most important laser properties are laser emission wavelength; output optical power; method of laser excitation, whether by optical pumping or electrical current injection; laser power consumption and efficiency; high-speed modulation or short pulse generation ability; wavelength tunability; output beam quality; device size; and so on. Thus, optical fiber communication (2), a major application that enables modern Internet, commonly requires lasers with emission wavelengths in the 1.55mm low- loss band of glass fibers and with single-transverse mode output beams for coupling into single-mode optical fibers. Typically, a given laser type excels in some of these properties, while exhibiting shortcomings in others. For example, by using different material compositions and structures, the most widely used semiconductor diode laser (3-12) can cover a wide range of wavelengths from the ultraviolet (UV) to the mid-IR, can be advantageously driven by diode current injection, and is very compact and efficient. However, the good beam quality, that is, single-transverse mode near- circular beam operation, can be typically achieved in semiconductor lasers only for output powers below 1 W. Much higher power levels are achievable from semicon- ductor lasers only with large aspect ratio highly multimoded poor quality optical beams. On the other hand, the solid-state lasers (13, 14), including fiber lasers (15), can emit hundreds of watts of output power with excellent beam quality, however, their emission wavelengths are restricted to discrete values of electronic transitions in ions, such as the classic 1064 nm wavelength of the Nd:YAG laser, making them
    Semiconductor Disk Lasers: Physics and Technology, 07/2010: pages 1 - 71; , ISBN: 9783527630394
  • Source
    [Show abstract] [Hide abstract]
    ABSTRACT: In the recent past we have studied the granulated silica method as a versatile and cost effective way of fiber preform production. We have used the sol-gel technology combined with a laser-assisted remelting step to produce high homogeneity rare earth or transition metal-activated microsized particles for the fiber core. For the fiber cladding pure or index-raised granulated silica has been employed. Silica glass tubes, appropriately filled with these granular materials, are then drawn to fibers, eventually after an optional quality enhancing vitrification step. The process offers a high degree of compositional flexibility with respect to dopants; it further facilitates to achieve high concentrations even in cases when several dopants are used and allows for the implementation of fiber microstructures. By this "rapid preform production" technique, that is also ideally suited for the preparation of microstructured optical fibers, several fibers have been produced and three of them will be presented here.
    International Journal of Modern Physics B 04/2014; 28(12). · 0.46 Impact Factor

Full-text (2 Sources)

Download
35 Downloads
Available from
May 21, 2014