Magnetic shielding properties of NbTi/Nb/Cu multilayer composite tubes

Nippon Steel Corp., Kawasaki
IEEE Transactions on Applied Superconductivity (Impact Factor: 1.32). 04/1993; DOI: 10.1109/77.233699
Source: IEEE Xplore

ABSTRACT Magnetic shielding properties have been investigated using Hall
plates at 4.2 K in a parallel magnetic field up to 4 T for
superconducting cylinders with and without a bottom, which are
multilayer composites consisting of NbTi, Nb, and Cu. These composite
cylinders were fabricated by deep drawing a multilayer composite sheet
made by cladding and rolling. It was found that a sample of five
concentrically stacked cup-shaped cylinders, with a thickness of 1 mm,
an inside diameter of 20-40 mm, and a length of 45 mm, can reduce the
external magnetic field of 3 T to less than 10 G

1 Follower
  • [Show abstract] [Hide abstract]
    ABSTRACT: Magnetic shielding from alternating magnetic field by a NbTi/Nb/Cu superconducting multilayer composite cylinder was investigated at liquid-helium temperatures. The specimen employed in this study was a slender seamless cylinder about 15 mm in diameter and having an aspect ratio of 6. The frequency of the alternating magnetic field was in the range of 40–500 Hz, and the maximum amplitude was 1000 G rms at 40 and 50 Hz owing to the capacity of the ac generator. The magnetic shielding efficiency of this cylinder, defined as the ratio of the magnetic field strength with and without the cylinder, was found to be of the order of 10−4. It was also found that the magnetic shielding effect depends upon the frequency investigated in this study. These shielding effects were mainly due to the shielding current originating from the superconductivity, which turned out to give superior shielding effect than that of a Cu cylinder.
    Journal of Applied Physics 05/1994; 75:6966-6968. DOI:10.1063/1.356767 · 2.19 Impact Factor
  • Source
    [Show abstract] [Hide abstract]
    ABSTRACT: The design of a cryogenic sensing element for superconducting DC current transformers working up to 100 kA at 4.2 K is proposed. Limitations of μ-metal magnetic characteristics at cryogenic conditions are overcome by a soft Ni 81-Mo 5-Fe magnetic alloy (referred to as cryogenic permalloy). An optimized geometrical design allows cores saturation due to mechanical constraints to be avoided. The effectiveness of the design is demonstrated through electromagnetic simulations exploiting measurement results from the characterization of cryogenic permalloy samples. Moreover, a preliminary lab-scale cryogenic DCCT prototype for a nominal current of 20 kA is implemented and characterized. A typical precision of the transducer below ±0.05% is achieved along with nonlinearity better than ±0.05%.
    Journal of Instrumentation 02/2014; 9(03). DOI:10.1088/1748-0221/9/03/P03011 · 1.53 Impact Factor
  • [Show abstract] [Hide abstract]
    ABSTRACT: The correlation between the microstructure and critical current density (Jc) of NbTi/Nb/Cu multilayer superconducting sheet has been studied. Two types of Ti precipitates have been found in the NbTi layers of the sheet. One type is elongated in the rolling direction with a major axis of about 240 nm and a minor axis of about 160 nm, and is precipitated at the grain boundaries. The other is fine, 20–30 nm in length, a few nanometers in thickness and is precipitated in crystal grains and at grain boundaries. The sum of the critical current densities calculated from the size and volume fraction of the two types of Ti precipitates and the Jc attributed to the dislocation pinning agree well with the measured Jc of the specimens. The Jc of transverse specimens subjected to the parallel 5 T magnetic field was about 1.2×103 A/mm2, and the Jc of longitudinal specimens subjected to the parallel 5 T magnetic field was 40% lower. The Jc of specimens subjected to the perpendicular magnetic field was about 40% of that of the specimens subjected to a parallel magnetic field. The dependence of Jc on the rolling and magnetic field directions can be qualitatively explained by the shape of Ti precipitates elongated in the rolling direction.
    Cryogenics 03/1998; 38(3):309–317. DOI:10.1016/S0011-2275(97)00160-4 · 0.94 Impact Factor